Eiki Projector Lc Hdt1000 User Manual

11

Part Names and Functions
Terminals and Connectors
r R/C JACK
  When using the wired remote control, connect the 
wired remote control to this jack with a remote 
control cable (supplied).
e USB CONNECTOR (series B)
  USB connector is to used to service the projector.
y S-VIDEO JACK
  Connects the S-VIDEO output signal from video 
equipment to this jack (p.21).
q 
SERIAL PORT IN TERMINAL
  If you control the projector from a computer, you 
must connect a cable (not supplied) from your 
computer to...

1

r FOCUS button
  Adjust
s the focus. (p.28)
e 
ZOOM button
  Zoom
s in and out the images. (p.28)
q ON/STAND-B y button
  Turn
s the projector on or off. (pp.24,25)
!0 
INPUT button
    Select
s an input source Input 1, Input 2, Input 3 or 
Input 4. (pp.32-34)
u 
AUTO PC ADJ. button
  Automatically adjust
s the computer image to its 
optimum setting. (pp.28, 36)
y 
POINT buttons
  -  Select an item or adjust the value in the On-
Screen MENU. (p.26)
   -  Pan the image in DIGITAL ZOOM + mode....

1

Indicators
e WARNING TEMP. indicator
  This indicator flashes red when internal projector 
temperature is too high. (pp.78, 85-87)
q 
POWER indicator
  This indicator lights green when the projector 
is ready to be turned on in standby mode. And 
it flashes green in Power Management mode. 
(pp.62, 85-87)
w 
LAMP Indicator
  This indicator is dim when the projector is turned 
on. And bright when the projector is in stand-by 
mode. (pp.85-87)
Part Names and Functions
r WARNING FILTER indicator
 –...

Remote Control
Part Names and Functions
!6 LIGHT button
  Lights the buttons on the remote control for about 10 seconds.
t MENU button
  Opens or closes the On-Screen MENU. (pp.26, 27)
y POINT ed 7 8 buttons
   –  Select an item or adjust the value in the ON-SCREEN MENU. (p.26)
   –Pan the image in DIGITAL ZOOM +/– mode. (p.44)
u LENS SHIFT button
  Selects the LENS SHIFT function. (p.29)
@0 FOCUS buttons
  Adjusts the focus. (p.29)
i ZOOM buttons
  Zoom in and out the images. (p.29)
!0 FREEZE button...

Remote Control Battery Installation
123
Open the battery 
compartment lid.
Install new batteries into 
the compartment.
Replace the 
compartment lid.
Two AAA size batteriesFor correct polarity (+ and –), be sure battery terminals are in contact with pins in the compartment.
To ensure safe operation, please observe the following precautions :
  l Use two (2) AAA or LR03 type alkaline batteries.
  l  Always replace batteries in sets.
  l  Do not use a new battery with a used battery.
  l  Avoid contact...

16

When controlling several projectors from each remote control at the same time, you can assign a remote 
control code (Code 1 - Code 8) to individual projectors and remote con\
trols to prevent remote control 
interference. Assign the same code the you specified for the projector to the remote control. See “Remote 
Control” on page 61 for assigning a remote control code to the projector. Follow the procedures below to select 
the assigned code. 
Remote Control Codes
Part Names and Functions
Press and...

17

Installation
Lens Installation
Before setting up the projector, install Projection Lens on the projector.
  Before installation, check where the projector is used and prepare a suitable lens. For the specifications of 
Projection Lens, contact sales dealer where you purchased the projector.
- Do not use the optional lens below for this projector.  Otherwise damages may result.
   LENS MODEL NO.  :  AH-101, AH-10
- Lens installation and replacement should be performed by the...

1

Installation
Picture Level and Pitch Adjustment
ADJUSTABLE
FEET
REAR ADJUSTABLE
FEET (Refer to p.10)
Projection lens can be moved from side to side and up and down with the motor-driven lens shift function.  This 
function makes the positioning of images easy on the screen. The amount of lens shift range varies depending 
on the lens. The shift ranges shown below apply to the AH-22051 lens. (See page 28)
Lens Shift Adjustment
When the lens is shifted to top.
The display position can be 
shifted...

19

Installation
Terminals of Projector
The projector has two replaceable Interface board slots. The projector's functions can be extended by installing 
the optional interface boards into the terminal slots. 2 vacant slots (Input 3 and 4) are provided in your 
purchasing the projector.  For the Optional Interface Boards, contact sales dealer where you purchased the 
projector.
Pull out the interface board.
Remove 2 Screws from an interface board.1
2
Tighten screws to secure the interface board....

0

Connecting to Computer
VGA 
Cable 
Monitor Output 
Desktop typeLaptop type
Terminals of
the projector
Monitor Output 
DVI-D Cable BNC Cable 
Monitor Output 
Unplug  the  power  cords  of  both  the 
projector  and  external  equipment  from 
the AC outlet before connecting cables.
Cables used for connection 
• DVI-D cable       • Serial cross cable
• DVI/HDMI cable      • USB cable
• VGA Cable (D-sub 15 pin) *
 ( *One cable is supplied; Other cables are not supplied with this projector.)
• BNC...