Eiki Projector Lc Hdt1000 User Manual

							
1

Remote Control
POINT buttons
KEYSTONE button
Press the KEYSTONE button on the remote control to switch 
the Standard (for Vertical/Horizontal) /Corner correction 
adjustment. The Standard or Corner correction adjustment 
dialog box appears. Use the Point ed 7 8 buttons to 
correct the Standard or Corner distortion. The Standard or 
Corner correction adjustment can be stored (see pages 45, 
52).
✔Note:
• The white arrows indicate that there is no 
correction.
•  A red arrow indicates the direction of correction.
•  An arrow disappears at the maximum correction.
•  If you press and hold the KEYSTONE button for
  more than 3 seconds while the Standard or Corner 
correction dialog box is being displayed, the 
Standard or Corner correction adjustment will be 
released.
•  The Corner pattern can be set to Off, Red, White or 
Blue in the Corner pattern function. See "Keystone" 
on pages 45, 52.
•  The adjustable range is limited depending on the 
input signal. 
•  Standard and Corner correction functions cannot 
be adjusted at the same time. If one of the 
functions is adjusted, and then the other one will 
be reset automatically. 
Reduce the top left corner part 
with the Point  8d  buttons. 
Reduce the top right corner 
part with the Point 7d buttons.  
Reduce the bottom left corner 
part with the Point 8e buttons. 
Reduce the bottom right 
corner part with the Point 7e buttons.  
Press the KEYSTONE button on the remote control to switch 
Corner correction adjustment, press the SELECT button on 
the remote control to select the corner you want to adjust. 
Reduce the right part with 
Point 8 button.  
Reduce the upper width 
with the Point e button. 
Reduce  the  left  part  with 
Point 7 button.  
Reduce the lower width 
with the Point d button.  
Press the SELECT button 
Press the SELECT button 
Press the SELECT button 
Press the SELECT button 
KeystoneKeystone
The top left corner adjustment as an example:
Press the Point 
d button
Press the Point 8 button
Keystone Correction
Standard
Corner correction
Keystone
Basic Operation 
						

							


The input source changes each time you press the INPUT button on the side control as follows:
 Input 1→Input 2→ ...
Before using the INPUT button on the side control or the remote control, you must select a correct input source 
by On-Screen Menu and the latest input source will be displayed.
Press the INPUT 1, INPUT 2, INPUT 3 or  INPUT 4 button on the remote control. The input source appears on 
the screen as you press each button. Select the connected input source.
INPUT 1 button
Input 1
RGB (PC analog)
RGB (Scart)
RGB(PC digital)
INPUT  buttonInput 
RGB
y,Pb/Cb,Pr/Cr
Video
Side Control
INPUT button
Direct Operation
Remote Control Operation
Side Control
INPUT 1/2/3/4 
buttons
Remote Control
S-videoRGB(AV HDCP)
HDMI
Input Selection
✔Note:
  • “Input  3”  and/or “Input  4”  are  selectable  only  when  interface board(s) are connected to either or both of the slots. 
						

							


WHEN SELECTING INPUT  (5 BNC INPUT JACKS )
INPUT MENU
When your computer is connected to the INPUT 1 
(ANALOG) terminal, select RGB (PC analog).
RGB(PC analog)
✔Note:
• Input  source  changes  if  the  INPUT  1  button  on  the  remote 
control is pressed.
When connecting the computer output [5 BNC Type (Green, 
Blue, Red, Horiz. Sync, and Vert. Sync.)] from the computer 
to G, B, R, H/HV, and V jacks:
When your computer is connected to the INPUT 2 (5 
BNC INPUT JACKS) terminal, select RGB.
RGB 
1


Press the MENU button to display the On-Screen 
Menu. Use the Point ed buttons to select Input and 
then press the Point 8 or the SELECT button. 
Use the Point ed buttons to select the desired input 
and then press the Point 8 button to access the 
submenu items. 
Use the Point ed buttons to select the desired 
source and then press the SELECT button.
INPUT  MENU
Computer Input Source Selection
Menu Operation
Input Selection
WHEN SELECTING INPUT 1 
  (COMPUTER INPUT TERMINALS )
✔Note: • “Input 3” and/or “Input 4” are selectable only when interface board(s) are connected to either or both of the slots. 
						

							
4

Input Selection
When the video input signal is connected 
to the Y, Pb/Cb, Pr/Cr jacks, select Y, Pb/
Cb, Pr/Cr.
When the video input signal is connected 
to the VIDEO jack, select Video.
When connecting to video equipment, select the type of 
Video source in the Source Select Menu. 
Video
y, Pb/Cb, Pr/Cr
When connecting to video equipment, select the type of 
Video source in the Source Select Menu. 
INPUT 1 MENU
HDMI
RGB(Scart)
When scart video equipment is connected to the INPUT 1 
(ANALOG) terminal, select RGB (Scart).
When the video signal is connected to the HDMI terminal, 
select HDMI.
INPUT  MENU
1


Press the MENU button to display the On-Screen 
Menu. Use the Point ed buttons to select Input and 
then press the Point 8 or the SELECT button. 
Use the Point ed buttons to select the desired input 
and then press the Point 8 button to access the 
submenu items. 
Use the Point ed buttons to select the desired 
source and then press the SELECT button.
Menu Operation
WHEN SELECTING INPUT 1 (COMPUTER INPUT 
TERMINALS )
WHEN SELECTING INPUT  (5 BNC INPUT JACKS )
✔Note:• When the video input signal is connected to the Y-Pb/Cb-Pr/Cr jacks, Y,Pb/Cb,Pr/Cr takes precedence of RGB.• Y,Pb/Cb,Pr/Cr input can accept the component signal and the analog RGB signal. When analog RGB signal is not recognized in Y,Pb/Cb,Pr/Cr input source, set to RGB input manually.
RGB(AV HDCP)
If the HDCP-compatible signal source is connected to the 
INPUT 1 (DIGITAL) terminal, select RGB (AV HDCP).
When the video input signal is connected to 
the S-VIDEO jack, select S-Video.
S-Video
Video Input Source Selection
RGB(PC digital)
When your computer is connected to INPU T 1 (DIGITAL) 
terminal, select RGB (PC digital). 
						

							
5

Computer Input
PC System Menu
PC System Menu
1

PC system can also be selected manually.
Selected system is displayed.
Press the MENU button to display the on-screen menu. 
Use the Point ed buttons to select Input and then 
press the Point 8 or the SELECT button. 
Use the Point ed buttons to select System and then 
press the Point 8 or the SELECT button.
Use the Point ed buttons to select the desired system 
and then press the SELECT button.
Systems in this dialog box can be selected.
Customized Mode (1-10) set in the PC adjust menu (pp.37, 38).
This projector automatically tunes to various types of computers with its Multi-scan system and Auto PC 
adjustment. If a computer is selected as a signal source, this projector\
 automatically detects the signal format 
and tunes to project a proper image without any additional settings. (Signal formats provided in this projector 
are shown on pages 88-90)
One of the following messages may appear when:
When the projector cannot recognize the 
connected signal conforming to the provided 
PC Systems, Auto is displayed on the System 
Menu box and the Auto PC adjustment function 
works to display proper images. If the image is 
not projected properly, a manual adjustment is 
required (pp.37, 38).
There is no signal input from the computer. 
Check the connection between your computer 
and the projector. (See “Troubleshooting” on 
pp.79-81.)
Auto
-----
The preset system is manually adjusted in the PC 
adjust menu. The adjusted data can be stored in 
Mode 1-10 (pp.37, 38).
Mode 1
PC Systems provided in this projector is chosen.  
The projector chooses a proper system provided 
in the projector and displays it.  
SVGA 1
*Mode 1 and SVGA 1 are examples.  
Computer System Selection
Automatic Multi-Scan System
Selecting Computer System Manually
One of the following messages may appear when: 
						

							
6

Computer Input
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Position H and Position V 
to conform to your computer. 
To store the adjusted parameters.The adjusted parameters from the Auto PC Adjustment can be stored in the projector. Once the parameters are stored, the setting can be done just by selecting Mode in PC System Menu (p.35). See “Manual PC Adjustment” on pages 37, 38.
✔Note:
 •  Fine  sync, Total  dots,  Position  H  and  Position  V    of  certain 
computers cannot be fully adjusted with the Auto PC Adjustment 
function.  When  the  image  is  not  provided  properly  with  this 
operation, manual adjustments are required. (pp.37, 38)
  • The  Auto  PC  adjustment  cannot  be  operated  when  480i,  575i, 
480p,  575p,  720p,  1035i,  1080i  or  1080p  is  selected  in  the  PC 
System  Menu  (p.35),  or  when  the  signal  is  coming  from  the 
HDMI/DVI-D terminal.
  •  Depending  on  the  condition  of  signals  and  the  type  and  length 
of cables, the signals may not be properly viewed.
The Auto PC adjustment function can be operated directly 
by pressing the AUTO PC button on the remote control.
AUTO PC button
Remote Control
Press the MENU button to display the On-Screen 
Menu. Use the Point ed buttons to select PC adjust 
and then press the Point 8 or the SELECT button.
1
Use the Point ed buttons to select Auto PC adj. and 
then press the SELECT button.
Use the Point ed buttons to select “Auto PC adj.” and press the SELECT button.Please wait... appears while the Auto PC adjustment is in process.
Auto PC Adjustment
Direct Operation
Menu Operation
Auto PC adj. 
						

							
7

Computer Input
Some computers employ special signal formats which may not be tuned by Multi-Scan system of this projector. 
Manual PC Adjustment enables you to precisely adjust several parameters to match those special signal formats. 
The projector has 10 independent memory areas to store those parameters manually adjusted. It allows you to 
recall the setting for a specific computer. 
Use  the  Point 7 8 buttons  to  adjust  the  value,  eliminating  a 
flicker from the image displayed (from 0 to 31).
Use the Point 7 8 buttons to adjust the number of total dots 
in one horizontal period to match your PC image.
Use  the  Point 7  8  buttons  to  adjust  the  horizontal  picture 
position.
Use  the  Point 7  8  buttons  to  adjust  the  vertical  picture 
position.
Press  the  SELECT  button  to  show  H-sync  freq.  and  V-sync 
freq. of  the connected computer.
Use  the  Point 7  8  buttons  to  adjust  the  clamp  level. When 
the image has dark bars, try this adjustment.
Use  the  Point 7  8  buttons  to  adjust  the  horizontal  area 
displayed by this projector.
Use  the  Point 7  8  buttons  to  adjusts  the  vertical  area 
displayed by this projector.
1

Press the MENU button to display the On-Screen Menu. 
Use the Point ed buttons to select PC adjust and then 
press the Point 8 or the SELECT button.
Use the Point ed buttons to select the desired item 
and then press the SELECT button to display the 
adjustment dialog box. Use the Point 7 8 buttons to 
adjust the setting value.
Manual PC Adjustment
Fine sync
Total dots
Position H
Position V
Current mode
Clamp
Display area H
Display area V 
						

							


Computer Input
✔Note
• Display area (H/V) cannot be selected when 480i, 575i, 480p, 
575p,  720p,  1035i  ,  1080i  or  1080p  is  selected  in  the  PC 
System Menu (p.35).
•  When  input  computer  signal  to  the  projector,  PC  adjust 
function will become available.
No parameters stored
This mode has stored parameters.
Values of Total dots, Position H, Position V, Display area H and Display area V.
Press the SELECT button 
to store the data.
Press the MENU button 
to close this dialog box.
Mode free 
Store 
To store the adjusted data, select Store and then press the 
Point 8 or the SELECT button. Move the highlight to one of the Modes 1 to 10 in which you want to store, and then press the SELECT button.
To clear the stored data, select Mode free and then press 
the Point 8 or the SELECT button. Move the highlight to the Mode that you want to clear and then press the SELECT button.
To reset the adjusted data, select Reset and press the SELECT button. A confirmation box appears and then select Yes. All adjustments will return to their previous figures.  
Press the SELECT button to clear the stored data.
Mode free
Store
Reset 
						

							
9

1

Normal picture level preset on the projector.
Picture level with improved halftone for graphics.
User  preset  picture  adjustment  in  the  Image  adjust  Menu. 
(pp.40-42)
Image select 
Press the MENU button to display the On-Screen 
Menu. Use the Point ed buttons to select Image 
select and then press the Point 8 or the SELECT 
button.
Use the Point ed buttons to select the desired item 
and then press the SELECT button.
Image Selection
Menu Operation
For viewing pictures in a bright room.
Computer Input
Dynamic
Standard
Real
Image 1–10 
						

							
40

Image Adjust MenuPress the MENU button to display the On-Screen 
Menu. Use the Point ed buttons to select Image 
adjust and then press the Point 8 or the SELECT 
button.
1
Use the Point ed buttons to select the desired item 
and then press the SELECT button to display the 
adjustment dialog box. Use the Point 7 8 buttons to 
adjust the setting value.
Press the Point 7 button to decrease the contrast; press the 
Point 8 button to increase the contrast (from 0 to 63).
Press the Point 7  button to decrease the brightness; press 
the Point 8 button to increase the brightness (from 0 to 63).
Use the Point 7 8 buttons 
to adjust the setting value.
Selected Image mode
Image Adjustment
Computer Input
The Color Management function can be used to adjust the LEVEL, 
PHASE, and GAMMA of the selected display colors (except for 
black, white, and gray) on the screen and replace these colors with 
other colors if required.
You can store up to eight (8) color management data.
1Select and highlight Color Management by using the Point 
ed buttons and press the SELECT button. The projected 
image freezes, and the COLOR MANAGEMENT POINTER 
appears.
Use the Point ed7 8 buttons to move the pointer to the 
spot where you want to adjust the color and then press the 
SELECT button. The COLOR SELECTION window appears, 
and the color in the center of the pointer is selected and you 
can adjust the color.
2
Use the Point ed7 8 buttons to adjust the LEVEL and 
PHASE of the color, and then press the SELECT button to 
confirm the setting. Then use the Point ed buttons to adjust 
the GAMMA for the color and press the SELECT button to 
accept the setting. After adjusting, press the SELECT button 
to go to the COLOR MANAGEMENT LIST.
3
Go to the COLOR MANAGEMENT LIST.
LIST
Return to the COLOR MANAGEMENT POINTER. (If you press 
the MENU button on the side control or the remote control , 
it returns to the COLOR MANAGEMENT POINTER and you 
will need to reselect and readjust the color.)
COLOR M.
COLOR MANAGEMENT POINTER
POINTER MODE
✔Note
When White  balance  Red,  Green  or  Blue  is  adjusted, 
Color temp. will change to Adj.
Contrast
Brightness
Color management
COLOR SELECTION MODE