Dukane Imagepro 8776-W Lcd Projector Users Manual

							
9

PICTURE Menu
PICTURE Menu
ItemDescription
BRIGHTNESSUsing the buttons ▲/▼ adjusts the brightness. :    Light ó Dark
CONTRASTUsing the buttons ▲/▼ adjusts the contrast. :    Strong ó Weak
GAMMA
Using the buttons ▲/▼ switches the GAMMA mode.
 # DEFAULT ó# CUSTOM ó # DEFAULT ó # CUSTOM ó #3 DEFAULT 
#5 CUSTOM ó #5 DEFAULT ó #4 CUSTOM ó #4 DEFAULT ó #3 CUSTOM
To adjust CUSTOM
Selecting a mode of CUSTOM and then pressing the button ► or the ENTER button displays a dialog to aid you in adjusting the mode. This function is useful when you want to change the brightness of particular tones.
Choose an item using the buttons ◄/►, and  adjust the level using the buttons ▲/▼. 
You can display a test pattern for checking the effect of your adjustment by pressing the ENTER button. Each time you press the ENTER button, the pattern changes as below.
  No pattern ð Gray scale of 9 steps 
                 Ramp  Gray scale of 5 steps
The eight equalizing bars correspond to eight tone levels of the test 
pattern  except  the  darkest  in  the  left  end.  If  you  want  to  adjust  the 

nd  tone  from  left  end  on  the  test  pattern  (Gray  scale  of  9  steps), 
use  the  equalizing  adjustment  bar  “ ”.  The  darkest  tone  at  the  left 
end  of  the  test  pattern  cannot  be  controlled  with  any  of  equalizing 
adjustment bar.
• When this function is performed, a certain extra such as a line 
may appear.
With  the  PICTURE  menu,  the  items  shown  in  the  table 
below can be performed. 
Select an item using the cursor buttons ▲/▼ on the 
projector or remote control, and press the cursor button ► 
on the projector or remote control, or the ENTER button 
on the remote control to execute the item. Then perform it 
referring to the following table. 
1
+0
2
+0
3
+0
4
+0
5
+0
6
+0
7
+0
8
+0GAMMA [CUSTOM 1]
ENTER :
/07=4)$?
+/#)5672
2+%674+0276
126+105%405*#42055
$4+)*60559×%1064#569×
%1.149×6+069×
%1.146/2/+&&.
)#//#&(#7.6
5.%6
/+7#5;/07/;//14;5#8 
						

							
30

ItemDescription
COLOR TEMP
Using the buttons ▲/▼ switches the mode of color temperature.
To adjust CUSTOM
Selecting the CUSTOM and then pressing the button ► or the ENTER button displays a dialog to aid you in adjusting the OFFSET and/or GAIN of the CUSTOM mode.
OFFSET adjustments change the color intensity on the whole tones of the test pattern.
GAIN adjustments mainly affect color intensity on the brighter tones of the test pattern.
Choose an item using the buttons ◄/►, and adjust the level using the buttons ▲/▼. 
You can display a test pattern for checking the effect of your adjustment by pressing the ENTER button.  Each time you press the ENTER button, the pattern changes as below.
  No pattern ð Gray scale of 9 steps 
                 Ramp  Gray scale of 5 steps
• When this function is performed, a certain extra such as a line 
may appear.
COLOR
Using the buttons ▲/▼ adjusts the strength of whole color.
Strong ó Weak
• This item can be selected only for a video signal, s-video or component video signal.
TINT
Using the buttons ▲/▼ adjusts the tint.
Greenish ó Reddish
• This item can be selected only for a video signal, s-video or component video signal.
SHARPNESS
Using the buttons ▲/▼ adjusts the sharpness.
Strong ó Weak• There may be some noise and/or the screen may flicker for a 
moment when an adjustment is made. This is not a malfunction.
PICTURE Menu
PICTURE Menu (continued)
R 
+0 
G 
+0 
B 
+0 COLOR TEMP [CUSTOM-1]
ENTER : OFFSET R 
+0 
G 
+0 
B 
+0 
GAIN 
HIGH DEFAULT � HIGH CUSTOM � MID DEFAULT � MID CUSTOM 
LOW DEFAULT � LOW CUSTOM � Hi-BRIGHT-1 DEFAULT � Hi-BRIGHT-1 CUSTOM  
Hi-BRIGHT-2 DEFAULT � Hi-BRIGHT-2 CUSTOM   
						

							
3

PICTURE Menu
ItemDescription
MY MEMORY
Selecting a mode of MY MEMORY using the buttons ▲/▼ and then pressing the button ► or the ENTER button performs each function.LOAD 
ó LOAD ó LOAD3 ó LOAD4
SAVE4 óSAVE3 ó  SAVE
 ó  SAVE

This projector has 4 numbered memories for adjustment data.  
Performing the LOAD, LOAD, LOAD3 or LOAD4 loads the data on 
the memory whose number corresponds to the command’s number, and adjusts the picture automatically depending on the data. Performing the SAVE, SAVE, SAVE3 or SAVE4 saves the current adjustment data on the memory whose number corresponds to the command’s number. • The current adjustment data of the items in the PICTURE menu is stored.• There may be some noise and/or the screen may flicker for a 
moment when data is loaded to memory. This is not a malfunction.
When  the  current  settings  are  not  saved  to  memory  the  following dialog is displayed.
To load saved adjustment settings press the MY BUTTON button.When there are no saved adjustment settings the following dialog is displayed.
~Note~ 
You have to assign the MY MEMORY function to the MY BUTTON 
(43).
PICTURE Menu (continued)
6GORQTCT[EQPFKVKQP//14;4GECNNUCXGFRCTCOGVGTU3WKV
0QUCXGFFCVC 
						

							
3

IMAGE Menu
IMAGE Menu
ItemDescription
ASPECT
Using the buttons ▲/▼ switches the mode for aspect ratio. For an RGB and MIU signalNORMAL ó 4:3 ó 6:9 ó SMALL         
For a video signal, s-video signal or component video signal4:3 ó 6:9 ó 4:9 ó SMALL     
For a no signal4:3 (fixed)• The NORMAL mode keeps the original aspect ratio of the signal.
OVER SCAN
Using the buttons ▲/▼ adjusts the over-scan ratio.Large (It reduces picture) ó Small (It magnifies picture)• This item can be selected only for a video, s-video and component signal.• When this adjustment is too large, certain degradation may appear at the frame area of the picture. In such a case, please adjust small.
V POSITION
Using the buttons ▲/▼ adjusts the vertical position.Up ó Down• Over-adjusting the vertical position may cause noise to appear on the screen. If this occurs please reset the vertical position to the \
default setting. Pressing the RESET button when V POSITION is selected will reset the V POSITION to the default setting.For a video signal, s-video signal or component video signalThe adjustable range of V.POSITION depends on the OVERSCAN setting.It is not possible to adjust when the OVERSCAN is set to 0.
H POSITION
Using the buttons ▲/▼ adjusts the horizontal position.Left ó Right• Over-adjusting the horizontal position may cause noise to appear on the screen. If this occurs please reset the horizontal position to the default setting. Pressing the RESET button when H POSITION is selected will reset the H POSITION to the default setting.For a video signal, s-video signal or component video signalThe adjustable range of H.POSITION depends on the OVERSCAN setting.
It is not possible to adjust when the OVERSCAN is set to 0.
H PHASE
Using the buttons ▲/▼ adjusts the horizontal phase to eliminate flicker .
Right ó Left
• This item can be selected only for an RGB signal or a component video signal. 
With the IMAGE menu, items shown in the table below can 
be performed. 
Select an item using the cursor buttons ▲/▼ on the 
projector or remote control, and press the cursor button ► 
on the projector or remote control, or the ENTER button 
on the remote control to execute the item. Then perform it 
referring to the following table. 
/07=4)$?
+/#)
2+%674
5.%6
#761#&,756:%76
#52%61845%#0
*2*#5*5+
						

							
33

IMAGE Menu
ItemDescription
H SIZE
Using the buttons ▲/▼ adjusts the horizontal size.
Large ó Small
• This item can be selected only for an RGB signal.
• When this adjustment is excessive, the picture may not be 
displayed correctly. In such a case, please reset the adjustment by pressing the RESET button on the remote control during this operation.
AUTO ADJUST EXECUTE
Selecting this item performs the automatic adjustment feature.
For an RGB signalThe vertical position, the horizontal position, the horizontal phase and the horizontal size will be automatically set to default. And the aspect ratio will be automatically selected. Make sure that the application window is set to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting.
For a video signal or s-video signalThe video format best suited for the respective input signal will be selected automatically.This function is available only when the AUTO mode is selected to the VIDEO FORMAT item in the INPUT menu. For a component video signal, the signal type is identified automatically independently of this function.For a video signal, s-video signal or component video signalThe vertical position, horizontal position and aspect ratio will be 
automatically set to default.
For a component video signalThe horizontal phase will be automatically set to default.
• The automatic adjustment operation requires about 0 seconds. Also please note that it may not function correctly with some input.
IMAGE Menu (continued) 
						

							
34

INPUT Menu
INPUT Menu
ItemDescription
PROGRESSIVE
Using the buttons ▲/▼ switches the progress mode.
TV ó FILM ó TURN OFF
• This function is performed only for an interlaced signal of a VIDEO 
input, an S-VIDEO input or COMPONENT VIDEO input of 5 5i (480i) 
or 65i (576i) signal.
• When TV or FILM is selected, the screen image will be sharp. 
FILM adapts to the -3 Pull-Down conversion system. But these 
may cause a certain defect (for example, jagged line) of the picture for a quick moving object. In such a case, please select TURN OFF, even though the screen image may lose the sharpness.
VIDEO NR
Using the buttons ▲/▼ switches the noise reduction mode.
HIGH ó MID ó LOW• This function performs only at a VIDEO input, an S-VIDEO or 
COMPONENT VIDEO input of 55i(480i) or 65i(576i) signal. 
• When this function is excessive, it may cause a certain degradation of the picture. 
COLOR SPACE
Using the buttons ▲/▼ switches the mode for color space. 
AUTO ó RGB ó  SMPTE40 ó REC709 ó REC60      
• This item can be selected only for an RGB signal or a component video signal (except signals of SCART RGB from the component video port).
• The AUTO mode automatically selects the optimum mode. 
• The AUTO operation may not work well at some signals. In such a case, it might be good to select a suitable mode except AUTO.
With  the  INPUT  menu,  the  items  shown  in  the  table  below 
can be performed. 
Select an item using the cursor buttons ▲/▼ on the 
projector or remote control, and press the cursor button ► 
on the projector or remote control, or the ENTER button 
on the remote control to execute the item. Then perform it 
referring to the following table. 
/07=4)$?
+/#)5672
2+%674+0276
126+10/+7#5;/07
5%40
5.%6
8+&1(14/#6#761
%1.1452#%#761
(4#/.1%-4)$+0
451.76+10
%1/21006%1/21006
674010
241)455+8688+&104/+& 
						

							
35

ItemDescription
COMPONENT
Using the buttons ▲/▼ switches the function of COMPONENT VIDEO port. 
COMPONENT ó SCART RGB 
When the SCART RGB is selected, the COMPONENT VIDEO port function as a port for a SCART RGB signal input and VIDEO port function as a port for SCART RGB sync input. A SCART adapter and SCART cable realize a SCART RGB input to the projector. For details, contact your dealer.
VIDEO FORMAT
Set the video format for the s-video port and video port.
() Use th
e ◄/► buttons to select the input port.
(2) Using the buttons ▲/▼ switches the mode for video format.
AUTO  ó  NTSC  ó  PAL  ó  SECAM 
      N-PAL ó M-PAL ó NTSC4.43 
• This item is performed only for a video signal from the VIDEO port or the S-VIDEO port. 
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well for some signals. If the picture becomes unstable (ex. an irregular picture, a color lack), please select the mode depending on the input signal.
FRAME LOCK
Using the buttons ▲/▼ turns the frame lock function on/off. 
TURN ON ó TURN OFF
• This item performs only at a RGB signal with vertical frequency of 50 to 60 Hz.
• When the TURN ON is selected, a moving picture is displayed more smoothly.
• This function may cause a certain degradation of the picture. In such a case, please select the TURN OFF.
RGB IN
Set the RGB input signal type for the RGB port.
() Use th
e ◄/► buttons to select the RGB port to be set.RGB 
ó  RGB
(2) Use the ▲/▼ buttons to select the RGB input signal type.
SYNC ON G ON ó SYNC ON G OFF
• Selecting TURN ON turns on the SYNC ON G mode. The SYNC ON G mode allows reception of SYNC ON G.• In the SYNC ON G mode, the picture may be distorted with certain input signals. In such a case, remove the signal connector so that no signal is received and turn SYNC ON G off, and then reconnect the signal.
INPUT Menu
INPUT Menu (continued)
4)$+04)$
5;0%10)1((5;0%10)104)$
8+&1(14/#658+&1#761065%2#.5%#/065%/2#.02#.
8+&1 
						

							
36

INPUT Menu
ItemDescription
RESOLUTION
*2The resolution for the RGB and RGB input signals can be set on 
this projector.
(1) In the INPUT menu select RESOLUTION using the ▲/▼ buttons and press the ► button.The RESOLUTION menu will be displayed.
()  In the RESOLUTION menu select the 
resolution you wish to display using the ▲/▼ buttons. Selecting AUTO will set a resolution appropriate to the input signal.
(3) Pressing the ► or Enter button when selecting a STANDARD resolution will automatically adjust the horizontal and vertical positions, clock phase and horizontal size and automatically select an aspect ratio. The INFORMATION dialog (45)  will be displayed.
(4) To set a custom resolution use the ▲/▼ buttons to select CUSTOM and the CUSTOM RESOLUTION BOX will be displayed. Set the horizontal (HORZ) and vertical (VERT) resolutions using the ▲/▼/◄/►
buttons. *
(5) To save the setting place the cursor on the right-most digit and press the ► button.The horizontal and vertical positions, clock phase and horizontal size will be automatically adjusted and an aspect ratio will be automatically selected. After the INFORMATION(45) dialog has 
displayed for about  0 seconds the screen will 
return to the RESOLUTION menu displaying the changed resolution.
(6) To revert back to the previous resolution without saving changes place the cursor on the left-most digit and press the ◄ button.The screen will then return to the RESOLUTION menu displaying the previous resolution.
INPUT Menu (continued)
451.76+10
56#0&
%7561/
#761ZZZ
Z
RESOLUTION MENU
INFORMATIONRGB80x 768@ 60
INFORMATIONRGB99x 744@ 60
451.76+10
56#0&
%7561/
#761ZZZ
Z
%7561/451.76+10
56

*14
						

							
37

SETUP Menu
SETUP Menu
ItemDescription
AUTO KEYSTONE EXECUTE
Selecting this item performs the Automatic keystone distortion correction. Projector automatically corrects vertical keystone distortion due to the (forward/backward) setup angle by itself.
• This function will be executed only once when selected in the Menu. When the slant of the projector is changed, executes this function again.
• When V:INVERT or H&V:INVERT is selected to the MIRROR item in the SETUP menu, if the projector screen is inclined or angled downward, this function may not work correctly.
• When the zoom adjustment is set to the TELE (telephoto focus), this correction may be excessive. This function should be used when the zoom adjustment is set to the WIDE (wide-angle focus) whenever possible.• When vertical degree is almost 0 degree, the automatic keystone distortion correction may not work.
• When vertical degree is over ±30 degree, the automatic keystone distortion correction may not work well.• This function will be unavailable when Transition Detector is on (50).
KEYSTONE
Using the buttons ▲/▼ corrects the keystone distortion.
Upper in the data ó Lower in the data
• The adjustable range of this function will vary with the type of input signal. At some signals, this function may not work well.
• This function will be unavailable when Transition Detector is on (50).
WHISPER
Using the buttons ▲/▼ turns off/on the whisper mode.
NORMAL ó WHISPER
• When the WHISPER is selected, acoustic noise and screen brightness are reduced.
With the SETUP menu, the items shown in the table below 
can be performed. 
Select an item using the cursor buttons ▲/▼ on the 
projector or remote control, and press the cursor button ► 
on the projector or remote control, or the ENTER button 
on the remote control to execute the item. Then perform it 
referring to the following table. 
/07=4)$?
+/#)5672
2+%674+0276
126+10/+7#5;/07
5%40
5.%6
9*+524014/#./+4414014/#.
-;5610
#761-;5610:%76
#7&+181.7/ 
						

							
38

SETUP Menu
SETUP Menu (continued)
ItemDescription
MIRROR
Using the buttons ▲/▼ switches the mode for mirror status.
NORMAL ó H:INVERT ó V:INVERT ó H&V:INVERT 
If Transition Detector is TURN ON and MIRROR status is changed, 
Transition Detector Alarm (50) will be displayed when projector is restarted after the power switch is turned off.
VOLUMEUsing the buttons ▲/▼ adjusts the volume.
High ó Low
AUDIO
Allocates the audio ports.
Choose a picture input port using the buttons ▲/▼ (1), then select the audio port to be interlocked with the input port using the buttons ◄/► (2). When off is selected, all audio ports do not work for the input port.
()  RGB ó RGB ó MIU ó COMPONENT ó S-VIDEO ó VIDEO
()   ó  ó 3 ó  ó M
M is abbreviation of MIU.
#7&+1
4)$/+7
37+64)$
58+&18+&1
%1/21006
/