Dukane Imagepro 8776-W Lcd Projector Users Manual

							
41

2. Equipment connection and network setting
2.5.11 Network Restart
Restarts the projector’s network connection.
ItemDescription
RestartRestarts the projector’s network connection in order to activate new configuration settings.
• Restarting requires you to re-log on in order to further control or 
configure the projector via a web browser.
NOTE
2.5.12 Logoff
When logoff is clicked, the logon screen is displayed (21 : Fig. 2.5.a).
2.5.10 Projector Status
Displays and configures the current projector status.
ItemDescription
Error StatusDisplays the current error status
Lamp TimeDisplays the usage time for the current lamp.
Filter TimeDisplays the usage time for the current filter.
Power StatusDisplays the current power status.
Input StatusDisplays the current input signal source.
Blank On/OffDisplays the current Blank On/Off status.
MuteDisplays the current Mute On/Off status.
FreezeDisplays the current Freeze On/Off status.
2.5 Configuring and controlling the projector via a web browser (Continued) 
						

							
42

Open browser when it is possible to communicate with projector. Corresponding 
browser is Internet Explorer 5.5 or later.
Specify http://(projector IP address)/ to start.
For example, http://192.168.1.10/
(Input this URL when IP address is not changed.)
After start up, enter your ID and password, and click [Logon]. Following window 
appears as shown in fig. 2.6.a. 
You can use your Web browser to remote control the projector once the projector 
is properly configured and connected to your PC via the wireless LAN card or via 
wired LAN.
2.6 Utilize Web Remote Control
• Do not attempt to control the projector with the projector's remote 
control and via your Web browser at the same time. Attempt to do so may 
causes a projector operational error.
NOTE
Fig. 2.6.a Utility selection window for Web Remote Control
2. Equipment connection and network setting 
						

							
43

2.6 Utilize Web Remote Control (Continued)
Click “Remote Control” in this window to display Web Remote Control as shown in 
fig.2.6.b.
The same operation as the 
bundled remote control will done.
UP/LEFT/RIGHT/DOWN 
corresponds to ▲/◄/►/▼ 
respectively.
Each mode will be activated by 
clicking these buttons.
• LIVE MODE
• THUMBNAIL
• SLIDE SHOW
• DIRECTORY
Fig. 2.6.b Web Remote Control
• Web Remote Control does not support repeat function when it is kept 
clicking.
• Since automatic repeat function is not available, click the button necessary 
times to reach your demand.
• If you click the button continuously, some command will not be transferred. 
Wait for a while, and Click again. 
• When the power button is pushed, a message comes up to confirm the operation.  
If you wish to turn it off, push OK, otherwise push CANCEL.
• PAGE DOWN and PAGE UP buttons on web remote control can not be used as 
mouse emulation function of the projector. 
NOTE
2. Equipment connection and network setting 
						

							
44

3. How to use Projector software – Basics -
This section explains how to use the “MIU Live Viewer”.
3.1 How to use “MIU Live Viewer”
3.1.1. Install “MIU Live Viewer”
In order to use the projector with a PC for Live Mode, you will first need to install 
the accompanying software on all the PCs you will be using.
 
• OS:    Windows 2000 Professional Service Pack4, 
 Windows XP Home Edition/Professional
• Graphic Interface:    DirectX 6.1a or higher; Video RAM 4MB or higher 
 (8MB recommended)
• CPU:  Pentium III (600MHz or higher recommended)
• Display: VGA 640x480 or higher (XGA 1024x768 recommended) 65,536
  simultaneous colors or higher
• Set your PC’s resolution to XGA or less.
• In some cases, Screen will not be displayed correctly like no displays larger 
than XGA portion.
• Images might not been transmitted, caused by OS version or the driver 
software for Network Adaptor. 
It is highly recommended that OS and the driver should be updated to the latest. 
NOTE
Minimum PC Hardware and Software Requirements
• Memory:    64MB or higher (128MB or higher if using Windows XP)
• Available Hard Disk Space:   10MB or higher
• Web browser:   Internet Explorer® (5.5 or higher)
• CD-ROM drive
• PC with PC card slot (PCMCIA Type-II) interface and IEEE802.11g wireless 
LAN PC card or PC with USB Interface and IEEE802.11g wireless LAN USB 
adaptor.
• Not required for PCs with built-in 802.11g wireless LAN.
• Depending on the type of wireless LAN card and PC you are using, the 
projector may not be able to communicate properly with your PC, even if the 
PC you are using is equipped with built-in wireless LAN functionality .
Should communication problems occur, please procure a Wi-Fi certified 
wireless LAN card.
NOTE
3. How to use Projector software – Basics - 
						

							
45

3. How to use Projector software – Basics -
3.1.2. Software Installation Procedure
1) Turn on the PC.
2) Shut down all applications.
3)  Insert the accompanying CD-ROM into the 
PC's CD-ROM drive.
4)  After a moment, the Welcome to MIU Utilities 
Setup dialog will appear as shown on the right. 
Press Next.
If the Welcome to MIU Utilities Setup dialog doesn't appear, proceed as 
follows:
(1) Click on the Start button on the toolbar and select Run.
(2) Enter E:\software\setup.exe and then press OK.
NOTE
If your CD-ROM drive is not drive E on your PC, you will need to 
replace E with the correct drive letter assigned to your CD-ROM 
drive.
5)   The License Agreement dialog appears. If you 
accept it, press the “Yes”.
6)  The Choose Destination Location dialog 
appears. Press Next.
• The C:\Program Files\MIU_Utility folder will be created and the 
program will be installed into that folder.
• If you wish to install to a different folder, click Browse and select another folder.
NOTE
7)   Confirm the program folder name.
  If MIU_Utility is okay, press Next to continue.
   If not, enter the desired folder name and then 
press Next.
3.1 How to use “MIU Live Viewer” (Continued)
If software has been already installed, Uninstallation will be done. Click the cancel 
button, then uninstallation will be canceled. If you uninstalled the software by mis-
operation, please re-install the software from first procedure. 
						

							
46

3.1 How to use “MIU Live Viewer” (Continued)
Fig. 3.1.3.a “MIU Live Viewer” Window
3.1.3 Explanation of  “MIU Live Viewer”
Double click “LiveViewer.exe” to start up. Fig. 3.1.3.a appears on your screen.
w
r
q
e
s
y
u
t
aoi
3. How to use Projector software – Basics -
8)  The Hardware Installation dialog appears. 
Press Continue Anyway.
9)  After a moment, installation will complete and 
the Setup Complete dialog will appear as 
shown on the right. Click Finish.
   This completes the software installation. Then 
your PC automatically restarts.
 (1)   To confirm that the software as been 
properly installed, press the Start button on 
the toolbar, select All Programs and then 
select the MIU Utility folder.
 (2)   MIU Live Viewer will appear in that folder if 
the installation was successful. 
						

							
47

3. How to use Projector software – Basics -
[“MIU Live Viewer” window: Fig. 3.1.3.a]
1)  “File” button 
Display file menu.
2)  “Help” button 
Display “MIU Live Viewer” information.
3)  Stop button 
Disconnect projector connection.
4)  Capture start button 
Start real time display. 
5)  Minimize button 
Close “MIU Live Viewer” window and display “MIU Live Viewer” as icon on the 
task tray.
6)  “Option” button 
Display Option window.
7)  “Refresh” button 
Refresh the current PC network setting.
8)  “Exit” button 
Terminate “MIU Live Viewer”.
9)  “Find” button 
Search connectable projectors.
10)   “One-Click” button 
Connect projector and PC without network setting of the PC.
11)  “Enable Device” 
Display network-connectable projector list.
3.1 How to use “MIU MIU Live Viewer” (Continued)
• When Multi PC mode is not selected, if there is no other PC 
connected, the last image will be held on screen until getting out of Live Mode 
or turning the projector off. 
Thanks to the feature, the PC can be used to prepare the next presentation file 
or others without showing it on screen if the communication to the projector is 
turned off. 
NOTE
• Pictures are not displayed correctly when the start/stop buttons are 
clicked repeatedly.
NOTE 
						

							
48

3. How to use Projector software – Basics -
3.1 How to use “MIU Live Viewer” (Continued)
1)  CPU Share 
Set up any capturing performance on the PC screen by using control bar
Low (At the far left): Set this position when many CPU resources are required 
by applications other than “MIU Live Viewer”. This setting is not 
good for displaying frequently changed patterns due to decrease in 
screen refresh rate by “MIU Live Viewer” performance degrading.
High (At the far right): Set this position when “MIU Live Viewer” requires many 
CPU resources. Screen refresh rate increases when “MIU Live 
Viewer” is used, but decreases the speed of other application 
speed.
2)  MultiPC Mode 
Select connected PC quantity from 1PC to 4PCs.
3)  Cursor Emulation 
Enabling this function “ON”, display cursor (pointer) prepared by this projector 
when cursor is not displayed on output screen. Take out check mark to make it 
“OFF” when PC and projector both cursors are displayed.
[“Options” window]
[“General” tab, Fig. 3.1.3.b]
Fig.3.1.3.b “Options”, “General” tab 
						

							
49

3. How to use Projector software – Basics -
1)  JPEG Quality 
When “MIU Live Viewer” is used, it captures PC screen image. Then that is 
compressed as JPEG and sent to projector. By control bar in this tab, you can 
set compression rate.
Low (At the far left, Low picture quality): Make JEPG compression rate high. 
Screen refresh interval becomes shorter due to low volume 
transferred data, but picture quality decreases.
High (At the far right, High picture quality): Make JEPG compression rate 
low. Screen refresh interval becomes longer due to high volume 
transferred data, but picture quality increases.
[JPEG tab]
Fig. 3.1.3.c “Options”, “JPEG” tab
3.1 How to use “MIU Live Viewer” (Continued)
[Icon in task tray]
To display “MIU Live Viewer” icon in task tray, click “Minimize” button in “MIU Live 
Viewer” window. The icon with yellow thunder mark shows that communication is 
connected, and it with red cross mark shows that it is disconnected. (Fig. 3.1.3.d 
shows while communication is disconnected.)
Fig. 3.1.3.d Icon in task tray
Double click “MIU Live Viewer” icon in task tray to display “MIU Live Viewer” 
window.  
						

							
50

3. How to use Projector software – Basics -
This section explains basic of how to use “MIU Live Viewer” functions.
• Before start up the MIU Live Viewer, you have to set the projector into LIVE 
MODE by either of following way.
1) from Web Remote Control
    (1) Select LIVE MODE
2)  from OSD Menu
    (1) Set the port into MIU menu by remote control or Keypad.
    (2)   Open the OSD Menu by pressing ▲/◄/►/▼ Keypad button on the projector 
or Menu button on remote control.
    (3)   Select the LIVE MODE in MIU Menu, and press the ► button on Keypad on 
the projector or Enter button on remote control.
3.1.4 Utilize “MIU Live Viewer” – Basic -
• After setting to the projector into LIVE MODE.
1)  Start “MIU Live Viewer”. If “MIU Live Viewer” installation is not completed, 
install it referring to 3.1.1 Install “MIU Live Viewer”.
Fig. 3.1.4.a Screen after “MIU Live Viewer” starting up
/07=4)$?
2+%674
5.%6

+/#)
5672+0276
126+10/+7#5;/07
5%40
.+8/1&2%.5524506#6+105672G5*16+0(14/#6+10548+%