Dukane Imagepro 8776-W Lcd Projector Users Manual

							


2. Equipment connection and network setting
Refer to the following for configuring or controlling the projector via a web browser.
Example: If the IP address of the projector is set to 192.168.1.10:
1)  Enter 
[http://192.168.1.10/] into the address 
bar of the web browser and the screen 
in Fig. 2.5.a will be displayed.
2)  Enter your ID and password and click 
[Logon].
If the logon is successful either the Fig.2.5.b or Fig.2.5.c screen will be displayed.
3)  Click the desired operation or configuration item on the main menu located on 
the left-hand side of the screen (Fig. 2.5.b or Fig. 2.5.c).
Fig. 2.5.b "Logon with administrator ID"Fig. 2.5.c "Logon with user ID"
Fig. 2.5.a "Logon Menu"
2.5 Configuring and controlling the projector via a web browser (Continued) 
						

							


2. Equipment connection and network setting
2.5.1 Network Information
All screen images displayed in this manual are 
screens of a logon using an administrator ID.
Any administrator only functions will not be 
displayed when using a user ID. Refer to the 
descriptions in each table.
Displays the projector’s current network configuration settings.
ItemDescription
DHCPDisplays the DHCP configuration settings.
IP AddressDisplays the current IP address.
Subnet MaskDisplays the Subnet Mask.
Default GatewayDisplays the Default Gateway.
MAC EthernetDisplays the Ethernet MAC address.
MAC WirelessDisplays the Wireless LAN MAC address.
Firmware DateDisplays the network firmware time stamp. This information is only displayed when logged on using an administrator ID.
Firmware VersionDisplays the network firmware version number. This information is only displayed when logged on using an administrator ID.
Wireless CH
Displays wireless LAN default channel. (Not Supported)
SD Card StatusDisplays SD card slot status. (Not Supported)
Wireless Speed
Displays wireless LAN connection speed. (Not Supported)
USB StatusDisplays USB-A port status. (Not Supported)
USB PowerDisplays USB-A port supplying power or not. (Not Supported)
• When you select wireless mode "AD-HOC", speed 
value is not true until the projector connect wireless LAN.
NOTE
2.5 Configuring and controlling the projector via a web browser (Continued) 
						

							


2. Equipment connection and network setting
2.5.2 Network Settings
Displays and configures network settings.
ItemDescription
NETWORK MODESelect Network mode "wired" or "wireless".
IP ConfigurationConfigures network settings.
DHCP ONEnables DHCP.
DHCP OFFDisables DHCP.
IP AddressConfigures the IP address when DHCP is disabled.
Subnet MaskConfigures the Subnet Mask when DHCP is disabled.
Default GatewayConfigures the Default Gateway when DHCP is disabled.
Projector NameConfigures the Projector name.
SysLocation (SNMP)Configures the location to be referred to when using SNMP.
SysContact (SNMP)Configures the contact information to be referred to when using SNMP.
DNS Server AddressConfigures the DNS Server address.
2.5 Configuring and controlling the projector via a web browser (Continued) 
						

							
24

Click the [Apply] button to save the settings.
• The new configuration settings are activated after restarting the 
network connection. When the configuration settings are changed, you must 
restart the network connection. You can restart the network connection by 
clicking [Network Restart] on the main menu.
• If you connect the projector to an existing network, consult a network 
administrator before setting server addresses.
NOTE
2. Equipment connection and network setting
2.5.2 Network Settings (Continued)
WEP Key
Input WEP key, which has same length defined by WEP. When "64bit" or "128bit" is selected, input 10 characters or 26 characters respectively. Only numbers from "0" to "9" and alphabets from "a" to "f" can be used.
WPA Passphrase
Input WPA Passphrase. Available number of input characters is 8 to 63. Only alphabets, numbers and following symbols can be used. 
!"#$%&'()*+,-./[¥]^_`{|}~
SSIDSet SSID. Maximum number of input characters is 32. Only alphabets, numbers and following symbols can be used. !"#$%&'()*+,-./[¥]^_`{|}~
ItemDescription

Wireless Mode
ModeSelect "AD-HOC" or "Infrastructure".
CH  (Communication channel)
Select using channel between "1" and "11".
Speed  (Communication speed)Select communication speed.
EncryptionSelect data encryption method.
• Depending on the country where you are 
the channels may vary. In addition, depending on the 
country or region where you are may be required to use 
a wireless LAN card that confirm to the standards in the 
respective country or region.
NOTE
2.5 Configuring and controlling the projector via a web browser (Continued) 
						

							


2. Equipment connection and network setting
2.5.3 Port Settings
Displays and configures communication port settings.
Click the [Apply] button to save the settings.
• The new configuration settings are activated after restarting the 
network connection. The network connection must be restarted when the 
configuration settings are changed. The network connection can be restarted 
using [Network Restart] on the main menu.
NOTE
ItemDescription
Network Control Port1 (Port:23)Configures command control port 1 (Port:23).
Port openClick the [Enable] check box to use port 23.
AuthenticationClick the [Enable] check box when authentication is required for this port.
Network Control Port2 (Port:9715)Configures command control port 2 (Port:9715).
Port openClick the [Enable] check box to use port 9715.
AuthenticationClick the [Enable] check box when authentication is required for this port.
SNMP PortConfigures the SNMP port.
Port openClick the [Enable] check box to use SNMP.
Trap addressConfigures the destination of the SNMP Trap in IP format.
SMTP PortConfigures the SMTP port.
Port openClick the [Enable] check box to use the e-mail function.
2.5 Configuring and controlling the projector via a web browser (Continued) 
						

							


2. Equipment connection and network setting
2.5.4 Mail Settings
Displays and configures e-mail addressing settings.
Click the [Apply] button to save the settings.
• You can confirm whether the mail settings work correctly using the 
[Send Test Mail] button.
• If you connect the projector to an existing network, consult a network 
administrator before setting server addresses.
NOTE
ItemDescription
Send MailClick the [Enable] check box to use the e-mail function. Configure the conditions for sending email under [Alert Settings].
SMTP Server IP AddressConfigures the address of the mail server in IP format.
Sender E-mail addressConfigures the sender e-mail address.The length of the sender e-mail address can be up to 255 alphanumeric characters.
Recipient E-mail address
Configures the e-mail address of up to five recipients. You can also specify [TO] or [CC] for each address. The length of 
the recipient e-mail address can be up to 255 alphanumeric characters.
2.5 Configuring and controlling the projector via a web browser (Continued) 
						

							


2. Equipment connection and network setting
2.5.5 Alert Settings
Displays and configures failure & warning alerts.
ItemDescription
Cover ErrorConfigures Cover Error alert settings.
SNMP TrapClick the [Enable] check box to enable SNMP Trap alerts for this item.
Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
Mail SubjectConfigures the subject line of the e-mail to be sent.The length of the subject line can be up to 255 alphanumeric characters.
Mail TextConfigures the text of the e-mail to be sent.The length of the text can be up to 1024 alphanumeric characters.
Fan ErrorConfigures Fan Error alert settings.
SNMP TrapClick the [Enable] check box to enable SNMP Trap alerts for this item.
Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
Mail SubjectConfigures the subject line of the e-mail to be sent.The length of the subject line can be up to 255 alphanumeric characters.
Mail TextConfigures the text of the e- mail to be sent.The length of the text can be up to 1024 alphanumeric characters.
2.5 Configuring and controlling the projector via a web browser (Continued) 
						

							
28

2. Equipment connection and network setting
2.5.5 Alert Settings (Continued)
ItemDescription
Lamp ErrorConfigures Lamp Error alert settings.
SNMP TrapClick the [Enable] check box to enable SNMP Trap alerts for this item.
Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
Mail SubjectConfigures the subject line of the e-mail to be sent.The length of the subject line can be up to 255 alphanumeric characters.
Mail TextConfigures the text of the e-mail to be sent.The length of the text can be up to 1024 alphanumeric characters.
Temp ErrorConfigures Temp Error alert settings.
SNMP TrapClick the [Enable] check box to enable SNMP Trap alerts for this item.
Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
Mail SubjectConfigures the subject line of the e-mail to be sent.The length of the subject line can be up to 255 alphanumeric characters.
Mail TextConfigures the text of the e-mail to be sent.The length of the text can be up to 1024 alphanumeric characters.
Air Flow ErrorConfigures Air Flow Error alert settings.
SNMP TrapClick the [Enable] check box to enable SNMP Trap alerts for this item.
Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
Mail SubjectConfigures the subject line of the e-mail to be sent.The length of the subject line can be up to 255 alphanumeric characters.
Mail TextConfigures the text of the e-mail to be sent.The length of the text can be up to 1024 alphanumeric characters.
2.5 Configuring and controlling the projector via a web browser (Continued) 
						

							


2. Equipment connection and network setting
2.5.5 Alert Settings (Continued)
ItemDescription
Lamp Time ErrorConfigures Lamp Time Error alert settings.
SNMP TrapClick the [Enable] check box to enable SNMP Trap alerts for this item.
Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
Mail SubjectConfigures the subject line of the e-mail to be sent.The length of the subject line can be up to 255 alphanumeric characters.
Mail TextConfigures the text of the e-mail to be sent.The length of the text can be up to 1024 alphanumeric characters.
Cool ErrorConfigures Cool Error alert settings.
SNMP TrapClick the [Enable] check box to enable SNMP Trap alerts for this item.
Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
Mail SubjectConfigures the subject line of the e-mail to be sent.The length of the subject line can be up to 255 alphanumeric characters.
Mail TextConfigures the text of the e-mail to be sent.The length of the text can be up to 1024 alphanumeric characters.
Filter ErrorConfigures Filter Error alert settings.
SNMP TrapClick the [Enable] check box to enable SNMP Trap alerts for this item.
Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
Mail SubjectConfigures the subject line of the e-mail to be sent.The length of the subject line can be up to 255 alphanumeric characters.
Mail TextConfigures the text of the e-mail to be sent.The length of the text can be up to 1024 alphanumeric characters.
2.5 Configuring and controlling the projector via a web browser (Continued) 
						

							
30

2. Equipment connection and network setting
2.5.5 Alert Settings (Continued)
ItemDescription
Other ErrorConfigures Other Error alert settings.
SNMP TrapClick the [Enable] check box to enable SNMP Trap alerts for this item.
Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
Mail SubjectConfigures the subject line of the e-mail to be sent.The length of the subject line can be up to 255 alphanumeric characters.
Mail TextConfigures the text of the e-mail to be sent.The length of the text can be up to 1024 alphanumeric characters.
Schedule Execution ErrorConfigures Schedule Execution Error alert settings.
SNMP TrapClick the [Enable] check box to enable SNMP Trap alerts for this item.
Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
Mail SubjectConfigures the subject line of the e-mail to be sent.The length of the subject line can be up to 255 alphanumeric characters.
Mail TextConfigures the text of the e-mail to be sent.The length of the text can be up to 1024 alphanumeric characters.
Lamp Time AlarmConfigures Lamp Time Alarm alert settings.
Alarm TimeConfigures the lamp time to alert.
SNMP TrapClick the [Enable] check box to enable SNMP Trap alerts for this item.
Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
Mail SubjectConfigures the subject line of the e-mail to be sent.The length of the subject line can be up to 255 alphanumeric characters.
Mail TextConfigures the text of the e-mail to be sent.The length of the text can be up to 1024 alphanumeric characters.
2.5 Configuring and controlling the projector via a web browser (Continued)