Digital Projection Titan 1080p 3d, Dual 3d, Titan 1080p 3d, Dual 3d Ultra Contrast, Titan Dual Fastframe User Manual

							
Rev B September 2010 Page 4.29
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 4. Controlling the projector

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section	4, 	Overview.

Notes
 None of the Geometry controls 
are available for Input 8.
 
Geometry Menu 
  Resolution
 Input Detection should 
normally be set to Automatic. 
However, if the incoming video 
signal is non-standard, the 
projector may not be able to 
select an appropriate input 
mode.
  In this case, 
Input Detection 
should be set to Manual or 
Custom.
 Input Standard is available 
only if Input Detection is set to 
Manual.
Resolution
Press  and   to select Resolution.
  Press 
 to open the Resolution submenu.
Input Detection
 Press  and   to select from:
Automatic Allows the projector to automatically detect an appropriate 
input mode for the signal.
Manual 
Allows the user to select an appropriate input mode from a list 
of common standards.
Custom 
Allows the user to completely customise the settings to suit the 
incoming video signal.
When Input Detection is set to Manual:
Press  and   to select Input Standard.
Press  and   to select from:
720p
XGA
XGA+
SXGA-
SXGA
SXGA+
1080p
UXGA
WUXGA
VGA
NTSC
PAL
SVGA
•
•
•
•
Geometry menu continued 
						

							
Page 4.30  Rev B September 2010
4. Controlling the projector Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

When Input Detection is set to Custom:
Press  and   to select one of the adjustment sliders.
  Press 
 and   to adjust the slider to match the resolution of the incoming 
video signal.
Blanking
Blanking curtains can be applied to each edge of the picture.
Press  and   to select Blanking.
  Press 
 to open the Blanking submenu.
Blanking On/Off
 Press  and   to select from:
On
Off
Blanking adjust
Press  and   to select the edge to be blanked.
  Press 
 and   to adjust the slider (0 to 200).
•
•
•
•
Notes
  None of the Geometry controls 
are available for Input 8.
  The adjustment sliders are 
available only if Input Detection 
is set to Custom.
 Total H Samples is available 
for RGB1 and RGB2 inputs 
only.
 V	Offset is available for DVI 
input only.
 
Geometry Menu 
  Blanking
 The blanking curtains will not 
applied until Blanking is turned 
On.
 The  On	Screen	Display	will 
move to the centre of the DMD 
when Blanking is turned On.
 Set to zero for no blanking, eg 
the top edge in this example.
Geometry menu continued 
						

							
Rev B September 2010 Page 4.31
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 4. Controlling the projector

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section	4, 	Overview.

Notes
  When using the menus, press 
OSD	
 or  to hide or 
reveal the On-Screen-Display.
 
Colour Menu
 Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 Read these notes on Colour 
and Global Colourimetry 
before making any settings in 
the Colour menus.
  Note that any changes made 
in the Global Colourimetry 
menu (see Setup Menu, later 
in this section) will affect ALL 
inputs, modes and presets for 
which Global Mode has been 
selected in the Colour menu.
Colour menu
 To return to the main menu, press  up to three times.
 From the main menu:
Press  and   until Colour is highlighted.
Press  to open the Colour menu. The blue highlight moves to the first item in 
the menu.
•
  Notes on Colour and Global Colourimetry
Global Colourimetry menu (see later in this section, in Setup menu)
After a calibration check on the projector or venue, a set of Global colour settings 
can be made in the Global Colourimetry menu. These settings are then available 
to be copied at any time using the Colour Mode setting in the Colour menu, or 
used as a starting point using the Trim feature in the Colour menu.
Colour menu (see this section).
The settings made in the Colour menu will be automatically saved in the Mode 
History, or can be manually saved to one of the Input Presets (see Input modes 
and settings earlier in this section).
The selections available in Colour Mode in the Colour menu are:
Global  Copies the settings made in the Global Colourimetry menu
Temperature  Set the colour temperature using the slider
User   Set the Red, Green and Blue Lift and Gain using the sliders
Peak  Preset high brightness setting
Video, Film,
Graphic  Applies the factory set P7 settings
ColorMAX User  Applies the User gamma settings made externally using the 
DP Userware on a personal computer 
						

							
Page 4.32  Rev B September 2010
4. Controlling the projector Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Notes
 Read the notes on Colour and 
Global Colourimetry earlier 
in this section before making 
any settings in the Colour 
menus.
  Note that any changes made 
in the Global Colourimetry 
menu (see Setup Menu, later 
in this section) will affect ALL 
inputs, modes and presets for 
which Global Mode has been 
selected in the Colour menu.
 The Colour Temperature 
slider is available  only if 
Temperature Mode is selected.
 The RGB Lift and Gain sliders 
are available  only if User Mode 
is selected.
 The Component Type 
selection is available for RGB1 
and Component inputs only.
Colour Mode
Press  and   to select Colour Mode.
  Press 
 and   to select from:
Global
Temperature
User
Peak
Video
Film
Graphic
ColorMAX User 1
ColorMAX User 2
Colour Temperature
Press  and   to select Temperature.
  Press 
 and   to adjust the slider (3,000K to 10,000K. in 100 steps).
RGB Lift
Press  and   to select the parameter to be adjusted.
  Press 
 and   to adjust the slider.
RGB Gain
Press  and   to select the parameter to be adjusted.
  Press 
 and   to adjust the slider.
Component Type
Press  and   to select Component Type.
  Press 
 and   to select from:
RGB
YPrPb
•
•
•
•
•
Colour menu continued 
						

							
Rev B September 2010 Page 4.33
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 4. Controlling the projector

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section	4, 	Overview.

Notes
  The Trim submenu is available  
only if Global Colour Mode is 
selected.
 
Colour Menu 
  Trim
 Read the notes on Colour and 
Global Colourimetry earlier 
in this section before making 
any settings in the Colour 
menus.
Trim
Press  and   to select Trim.
  Press 
 to open the Trim submenu.
t rim rGB Lift and Gain
Press  and   to select the parameter to be adjusted.
  Press 
 and   to adjust the slider (-128 to +127).
Global Colourimetry
 This is a shortcut to the Global Colourimetry submenu, described  later in this 
section, in Setup Menu.
Press  and   to select Global Colourimetry.
  Press 
 to open the Global Colourimetry submenu.
•
•
•
Colour menu continued 
						

							
Page 4.34  Rev B September 2010
4. Controlling the projector Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Notes
  When using the menus, press 
OSD	
 or  to hide or 
reveal the On-Screen-Display.
 
Setup Menu
Setup menu
 To return to the main menu, press  up to three times.
 From the main menu:
Press  and   until Setup is highlighted.
Press  to open the Setup menu. The blue highlight moves to the first item in 
the menu.
• 
						

							
Rev B September 2010 Page 4.35
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 4. Controlling the projector

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section	4, 	Overview.

Projector Setup
Press  and   to select Projector.
  Press 
 to open the Projector submenu.
Orientation
Press  and   to select Orientation.
  Press 
 and   to select from:
Desktop Front
Desktop Rear
Ceiling Front
Ceiling Rear
Control panel Backlight
Press  and   to select Backlight.
  Press 
 and   to select from:
On
Off
•
•
•
Setup menu, continuedNotes
 
Setup Menu 
  Projector Setup
 A Component Video Sync 
setting was available in earlier 
models, but for the Component 
input only.
  In later models, the sync type is 
detected automatically. 
						

							
Page 4.36  Rev B September 2010
4. Controlling the projector Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Notes
 Keystone adjustment can be 
found in both the Geometry and 
Projector Setup menus.
 The Keystone adjustment is 
NOT available for Input 8.
  The range of adjustment will 
be dependent on the input 
resolution.
 Some computer graphics cards 
do not recognise the EDID 
Extension block.
  If you are having problems 
booting a computer connected 
to the projector:
turn the computer OFF
set DVI EDID Extension Block 
to Disable
turn the computer back ON 
again 
•
•
•
Keystone
Used to correct for distortion caused by the projector being mounted higher or lower 
than the screen.
Press  and   to select Keystone.
  Press 
 and   to adjust the slider.
DVI EDID Extension Block
Press  and   to select DVI EDID Extension Block.
  Press 
 and   to select from:
Enable
Disable
•
•
Setup menu, projector Setup continued 
						

							
Rev B September 2010 Page 4.37
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 4. Controlling the projector

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section	4, 	Overview.

Test Patterns
Press  and   to select Test Patterns.
  Press 
 to open the Test Patterns submenu.
  Press 
 and   to select from:
Off
Alignment Grid
Screen Layout     (shows outlines of various aspect ratios)
Chequerboard
Colour Bars
0% Field      (black)
ColorMAX Calibration
100% Field (Corrected White)  (white, affected by colour settings)
100% Field (Peak White) 
(white, unaffected by colour settings)
•
Notes
 
Setup Menu 
  Projector Setup
 
    Test Pattern
 The only test pattern available 
for Input 8 is:
 100% Field (Corrected White).
Setup menu, projector Setup continued 
						

							
Page 4.38  Rev B September 2010
4. Controlling the projector Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Setup menu, projector Setup continued
FastFrame
Used to reduce the artifacts and image blur typically associated with rapidly moving 
images, by increasing the time the display is blanked between frames (dark time).
From the Projector Setup menu, press  and   to select FastFrame.
Press  to open the FastFrame submenu.
FastFrame On/Off
Press  and   to select Fastfame.
  Press 
 and   to select from:
On
Off
Dark t ime
 Press  and   to select Dark Time.
  Press 
 and   to adjust the slider.
•
•
•
•
Notes
 
Setup Menu 
  Projector Setup
 
    FastFrame
 If FastFrame is turned on, then 
turning on 3D Enable will turn it 
off.
  When 
3D Enable is on, it is not 
possible to turn on FastFrame.
 The optimum dark time setting 
for a 60Hz frame rate is 
approximately 8 to 10mS.