Digital Projection Titan 1080p 3d, Dual 3d, Titan 1080p 3d, Dual 3d Ultra Contrast, Titan Dual Fastframe User Manual

							
Rev B September 2010 Page 4.39
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 4. Controlling the projector

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section	4, 	Overview.

Notes
 
Setup Menu 
  Projector Setup
 
    Edge Blend
 
Setup Menu 
  Projector Setup
 
    Edge Blend
 
      Active Edges
Edge Blend
Used to improve the appearance of multi-projector displays, by blending overlapping 
edges to present a seamless image.
Examples
From the Projector Setup menu, press  and   to select Edge Blend
Press  to open the Edge Blend Setup submenu.
Active Edges
Press  and   to select Active Edges.
  Press 
 to open the Active Edges submenu.
 Press  and   to select the edges to be blended.
For each edge, press  and   to select from:
On
Off
•
•
•
•
Setup menu, projector Setup continued
Four projectors, two active edges eachTwo projectors, one active edge each 
						

							
Page 4.40  Rev B September 2010
4. Controlling the projector Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Notes
  The actual blend will be 
smoother than that shown here.
 Edges that have not been 
selected as Active, will be 
greyed out.
 To see the effect of the 
adjustment, turn the Overlap 
Markers ON..
 Input 8 is pixel-mapped directly 
to the DMDs, so the image may 
be smaller than full-screen.
 Input 8 DVI 3D Resolution 
should normally be set to 
Automatic. However, if the 
incoming video signal is non-
standard, the projector may not 
be able to select an appropriate 
input size.
  In this case, set the resolution 
to one of the settings provided. 
(Settings larger than the DMD 
will not available, depending on 
model.)
 This setting will have no effect 
on Inputs 1–7.
Overlap markers
The markers show the extent of the overlap, and can be used as an alignment guide 
when adjusting the position of the images.
Press  and   to select Overlap Markers.
Press  and   to select from:
On
Off
Overlap adjust
Used to determine the size of the overlap.
 Press  and   to select the edge to be blended.
  For each edge, press 
 and   to adjust the slider (0 to 511).
Input 8 DVI 3D resolution
Press  and   to select Input 8 DVI 3D Resolution.
  Press 
 and   to select from:
Automatic
HD2     1280 x 720
SXGA  1280 x 1024
SX+    1400 x 1050
1080p  1920 x 1080
UXGA  1600 x 1200
WUXGA  1920 x 1200
•
•
•
•
Setup menu, projector Setup, Edge Blend continued 
						

							
Rev B September 2010 Page 4.41
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 4. Controlling the projector

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section	4, 	Overview.

Black Level Uplift
As it is not possible for any projector to produce an absolute black, any ‘black’  areas 
in the overlapped edges may appear slightly less dark than those in the rest of the 
image.
Black Level Uplift can be used to counteract this effect, by raising the black level 
of the rest of the image. The amount of uplift required will be either x2 or x4, 
depending on how many images are overlapped, as shown in the examples below .
Examples
 From the Edge Blend menu, press  and   to select Black Level Uplift.
Press  to open the Black Level Uplift Setup submenu.
Uplift Adjustment
Used to determine the amount of uplift.
 Press  and   to select x2 Region Uplift or x4 Region Uplift.
For each region, press  and   to adjust the slider (0 to 340).
•
•
•
Setup menu, projector Setup, Edge Blend continuedNotes
 
Setup Menu 
  Projector Setup
 
    Edge Blend
 
      Black Level Uplift Setup
 This adjustment affects the 
amount of Black Level Uplift, 
not the size of the region.
Four projectors, with four x2 uplift 
regions and four x4 uplift regions
Two projectors, with two x2 uplift 
regions
x2x2x4x4
x4x4
x2
x2
x2x2
no uplift
no uplift 
						

							
Page 4.42  Rev B September 2010
4. Controlling the projector Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Notes
  The size of the border 
varies due to manufacturing 
tolerances, so Non-
Addressable Border should 
always be set to Manual.
  Working on one projector at a 
time, display a test pattern of 
0% Field (black), set all four 
border adjustments to zero, 
then increase the size of each, 
until the border disappears.
Non-Addressable Border
Around the edge of the DMD is a border of non-addressable ‘always off ’ pixels. 
Although ‘always off’, a small amount of stray light from these pixels can cause a 
faint border around the projector image.
A small black level adjustment can be applied to remove this border.
Press  and   to select Non-Addressable Border.
  Press 
 and   to select from:
Automatic
Manual  (recommended)
Border Adjustment
Press  and   to select the edge that is to be adjusted.
  For each edge, press 
 and   to adjust the slider (0 to 255).
•
•
Setup menu, projector Setup, Edge Blend continued 
						

							
Rev B September 2010 Page 4.43
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 4. Controlling the projector

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section	4, 	Overview.

Notes
 
Setup Menu 
  Global Colourimetry
 Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 Read these notes on Colour 
and Global Colourimetry 
before making any settings in 
the Colour menus.
  Note that any changes made in 
the Global Colourimetry menu 
will affect ALL inputs, modes 
and presets for which Global 
Mode has been selected in 
the Colour menu (see Colour 
Menu, earlier in this section).
Global Colourimetry
Press  and   to select Global Colourimetry.
Press  to open the Global Colourimetry submenu.
•
•
Setup menu continued
  Notes on Colour and Global Colourimetry
Global Colourimetry menu (see this section)
After a calibration check on the projector or venue, a set of Global colour settings 
can be made in the Global Colourimetry menu. These settings are then available 
to be copied at any time using the Colour Mode setting in the Colour menu, or 
used as a starting point using the Trim feature in the Colour menu.
Colour menu (see earlier in this section).
The settings made in the Colour menu will be automatically saved in the Mode 
History, or can be manually saved to one of the Input Presets (see Input modes 
and settings earlier in this section).
The selections available in Colour Mode in the Colour menu are:
Global  Copies the settings made in the Global Colourimetry menu
Temperature  Set the colour temperature using the slider
User   Set the Red, Green and Blue Lift and Gain using the sliders
Peak  Preset high brightness setting
Video, Film,
Graphic  Applies the factory set P7 settings
ColorMAX User  Applies the User gamma settings made externally using the 
DP Userware on a personal computer 
						

							
Page 4.44  Rev B September 2010
4. Controlling the projector Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Notes
 Read the notes on Colour and 
Global Colourimetry earlier 
in this section before making 
any settings in the Colour 
menus.
  Note that any changes made in 
the Global Colourimetry menu 
will affect ALL inputs, modes 
and presets for which Global 
Mode has been selected in 
the Colour menu (see Colour 
Menu, earlier in this section).
 The Colour Temperature 
slider is available  only if 
Temperature Mode is selected.
 The RGB Lift and Gain sliders 
are available  only if User Mode 
is selected.
Colour Mode
Press  and   to select Colour Mode.
  Press 
 and   to select from:
Temperature
User
Peak
Video
Film
Graphic
ColorMAX User 1
ColorMAX User 2
Colour t emperature
Press  and   to select Temperature.
  Press 
 and   to adjust the slider (3,000K to 10,000K. in 100 steps).
rGB Lift
Press  and   to select the parameter to be adjusted.
  Press 
 and   to adjust the slider.
rGB Gain
Press  and   to select the parameter to be adjusted.
  Press 
 and   to adjust the slider.
•
•
•
•
Setup menu, Global Colourimetry continued 
						

							
Rev B September 2010 Page 4.45
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 4. Controlling the projector

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section	4, 	Overview.

Lamp Setup
Press  and   to select Lamp.
  Press 
 to open the Lamp submenu.
The middle row shows the current lamp setting.
Change Lamp Setting
Press  and   to select Change Lamp Setting.
Press  to open the Lamp Setting control box.
single lamp models
dual lamp models
•
•
Setup menu, continuedNotes
 
Setup Menu 
  Lamp
 Lightning projectors have only 
one lamp. 
 
Titan projectors may have one 
or two lamps.
continued 
						

							
Page 4.46  Rev B September 2010
4. Controlling the projector Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Lamp power
Press  and   to select the Lamp Power setting.
  Press 
 and   to adjust the Lamp Power from:
  80 to 100%  in 1% steps
Lamp Mode
Press  and   to select Lamp Mode.
  Press 
 and   to select from:
single lamp modes
Lamp 1  lamp 1 only
Lamp 2  lamp 2 only
Alternate  on power up, selects the lamp with the least hours used
dual lamp mode
Lamps 1 and 2  both lamps
After setting the Power and Mode, press  and   to select from
OK
 Press  
 to apply the new settings.
or 
Cancel
  Press  
 or   to exit without applying the new settings.
The indicators on the control panel will show as follows:
Lamp 1 off = OFF
  flashing red  = LAMP ERROR 
green = ON (100%) amber = (80 - 99%)
 flashing green  = LAMP WARM-UP    flashing amber  = COOL-DOWN
Lamp 2 off = OFF
 flashing red  = LAMP ERROR green = ON (100%) amber = (80 - 99%)
 flashing green  = LAMP WARM-UP    flashing amber  = COOL-DOWN
•
•
•
Setup menu, Lamp Setup continuedNotes
 Lamp Mode applies to t itan 
projectors only:
 For Dual lamp models in single 
lamp mode:
  - if the running lamp fails, the 
other lamp will automatically be 
switched on.
 The Lamp 2 and Alternate 
settings apply to Dual lamp 
models only.
 The selected lamp mode:
  - will not be applied until 
OK is 
selected
  - will be applied gradually over a 
period of 30 seconds
  - will not be applied until the end 
of any warm-up or cool-down 
period that has already started.
 The Lamp 2 indicator applies 
only to Titan Dual models. 
 
Lightning projectors have only 
one lamp. 
						

							
Rev B September 2010 Page 4.47
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 4. Controlling the projector

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section	4, 	Overview.

Notes
 
Setup Menu 
  On Screen Display
 The  On	Screen	Display will 
move to the centre of the DMD 
when Blanking is turned On.
  (see 
Geometry menu, earlier in 
this section).
 If a menu is opened, and no 
other key is pressed within the 
period set in the  OSD	Timeout 
menu, then the menus will 
disappear. When the   key 
is pressed again, the menus will 
reopen at the same point they 
were last viewed.
On	Screen	Display
Press  and   to select On Screen Display.
  Press 
 to open the On Screen Display submenu.
OSD position
Press  and   to select OSD Position
  Press 
 and   to select from:
Upper Left
Upper Centre
Upper Right
Middle Left
Middle Centre
Middle Right
Lower Left
Lower Centre
Lower Right
OSD Size
Press  and   to select OSD Size.
  Press 
 and   to select from:
Large
Small
OSD t imeout
Press  and   to select the length of the On Screen Display Timeout.
  Press 
 and   to select from:
  0 to 255  in 1 second steps 
(when set to zero, the OSD never times out)
•
•
•
•
Setup menu continued 
						

							
Page 4.48  Rev B September 2010
4. Controlling the projector Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Password
Entry to the password protected area is available to authorised service personel 
only.
Press  and   to select Password.
  Press 
 to open the Password control box.
Press  and   to select each digit in turn.
  Press 
 and   to adjust the digit from:
0 to 9
 then move to the next digit.
  Use 
 and   to select from
OK
 Press  
 to enter the password controlled area.
or  Cancel
Press   or   to exit without applying the password.
•
•
NotesSetup menu continued