Digital Projection Titan 1080p 3d, Dual 3d, Titan 1080p 3d, Dual 3d Ultra Contrast, Titan Dual Fastframe User Manual

							
Rev B September 2010 Page 4.59
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 4. Controlling the projector

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section	4, 	Overview.

Lens Setup
Press  and   to select Lens.
  Press 
 to open the Lens submenu.
Centre Lens
Press  and   to select Centre Lens.
  Press 
 to centre the lens.
Calibrate Focus
Press  and   to select Calibrate Focus.
  Press 
.
The focus mechanism will operate for about a minute, whilst the minimum and 
maximum travel distances are determined.
Calibrate Zoom
Press  and   to select Calibrate Zoom.
  Press 
.
The zoom mechanism will operate for about a minute, whilst the minimum and 
maximum travel distances are determined.
•
•
•
•
Setup menu, continuedNotes
  Each time a new lens is 
fitted	to	the	projector,	the	
calibration procedure must 
be carried out.
  Note that two shortcuts are 
available using the remote 
control:
 Calibrate Focus:  
 Calibrate Zoom:   
						

							
Page 4.60  Rev B September 2010
4. Controlling the projector Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Notes
 Restore Defaults will restore 
all settings to factory 
defaults. All ISF settings will 
be lost (see next page).
  If you are not sure this is 
what you want to do, then 
either:
 make a record of all settings 
first 
 
or 
select No, then press .
 Following a restore to factory 
defaults, the projector will 
perform a self-test and enter 
Standby mode.
  This process will take up to 10 
seconds. During this time the 
projector will not respond to any 
commands.
  When complete, all settings will 
be restored to factory condition 
and all user settings will be 
removed except for downloaded 
colour and gamma parameters.
Restore Defaults
Press  and   to select Restore Defaults.
  Press 
.
  The following message will be displayed.
  Press 
 and   to select from:
Yes
 Press  
 to confirm your that you really wish to restore all default settings.
All settings will be restored to factory defaults.
or  No
Press   or   to exit without making the change.
•
•
Setup menu, continued 
						

							
Rev B September 2010 Page 4.61
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 4. Controlling the projector

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section	4, 	Overview.

Notes
  When using the menus, press 
OSD	
 or  to hide or 
reveal the On-Screen-Display.
 
Information Menu
 If Distributed By is visible, then 
the installer is  iSf	Certified, 
and the Save and Delete 
Preset options will not be 
available. Contact the installer 
for more information.
 
Information Menu 
  Projector Information
 Lightning projectors have only 
one lamp. 
 
Titan projectors may have one 
or two lamps.
 
Information Menu 
  Source Information
Information menu
 To return to the main menu, press  up to three times.
 From the main menu:
Press  and   until Information is highlighted.
Press  to open the Information menu. The blue highlight moves to the first 
item in the menu.
Projector Information
Press  and   to select Projector Information.
  Press 
 to open the Projector Information submenu.
Source Information
Press  and   to select Source Information.
  Press 
 to open the Source Information submenu.
•
•
•
Input
Picture
Geometry
Colour
Setup
Information
Input:DVI
Standard:720p 60
FrequencyV:60HzH:45.0KHz
SOURCEINFORMATION 
						

							
Page 4.62  Rev B September 2010
4. Controlling the projector Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.
Digital Projection Information
Press  and   to select Digital Projection.
  Press 
 to see the DP Information screen.
•
Information menu continuedNotes
  When using the menus, press 
OSD	
 or  to hide or 
reveal the On-Screen-Display.
 
Information Menu 
  DP Contact Information 
						

							
Rev B September 2010 Page 5.1
5. Userware
continued
Contents
Introduction ..........................................................................................................................................5.4
Applet version...................................................................................................................................5.4
Disconnect ....................................................................................................................................5.4
Reconnect.....................................................................................................................................5.4
Standalone version ...........................................................................................................................5.5
Disconnect ....................................................................................................................................5.5
Reconnect.....................................................................................................................................5.5
Show page ............................................................................................................................................5.6
On / Off ............................................................................................................................................5.6
Shutter Open / Closed .......................................................................................................................5.6
Freeze / Un-Freeze ...........................................................................................................................5.6
Picture sliders ...................................................................................................................................5.6
Input Presets ....................................................................................................................................5.7
Recall ..........................................................................................................................................5.7
Save ............................................................................................................................................5.7
Orientation .......................................................................................................................................5.8
Input ................................................................................................................................................5.8
Test Pattern ......................................................................................................................................5.8
Aspect Ratio .....................................................................................................................................5.8
Lens page .............................................................................................................................................5.9
Lens controls ....................................................................................................................................5.9
Shutter Open / Closed .......................................................................................................................5.9
Calibrate Focus ................................................................................................................................5.9
Calibrate Zoom .................................................................................................................................5.9
Edge Blend page ...............................................................................................................................5.10
Markers On / Off .............................................................................................................................5.10
Active Edges ..................................................................................................................................5.10
Input 8 DVI 3D Resolution ...............................................................................................................5.10
Overlap Width.................................................................................................................................5.10
Black Level Uplift page .....................................................................................................................5.11
x2, x4 Region Uplift ..........................................................................................................................5.11
Non-Addressable Border ..................................................................................................................5.11
Back to Edge Blend..........................................................................................................................5.11 
						

							
Page 5.2  Rev B September 2010
5. Userware Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Image page .........................................................................................................................................5.12
Colour Space .................................................................................................................................5.12
Component ....................................................................................................................................5.12
Phase slider ...................................................................................................................................5.12
Gamma ..........................................................................................................................................5.12
Parametric slider .............................................................................................................................5.12
Convergence controls .....................................................................................................................5.13
Horizontal Convergence ..................................................................................................................5.13
Vertical Convergence ......................................................................................................................5.13
Close .............................................................................................................................................5.13
Screen page .......................................................................................................................................5.14
Blanking On / Off ............................................................................................................................5.14
Blanking adjust ...............................................................................................................................5.14
Keystone adjust ..............................................................................................................................5.14
Position adjust ................................................................................................................................5.14
MCGD page ........................................................................................................................................5.15
The MCGD measurement procedure ................................................................................................5.15
MCGD edit boxes ...........................................................................................................................5.16
Write to Projector ............................................................................................................................5.16
Read from Projector ........................................................................................................................5.16
Save File ........................................................................................................................................5.16
Open File .......................................................................................................................................5.16
TCGD page .........................................................................................................................................5.17
TCGD values ..................................................................................................................................5.17
Update Graph .................................................................................................................................5.18
Save File ........................................................................................................................................5.18
Open File .......................................................................................................................................5.18
Write User 1, User 2 ........................................................................................................................5.18
Read User 1, User 2 .......................................................................................................................5.18
3D page ...............................................................................................................................................5.19
3D Enable ......................................................................................................................................5.19
Dark Time ......................................................................................................................................5.19
Sync Delay .....................................................................................................................................5.19
Frame Dominance ..........................................................................................................................5.19
3D Sync Source ..............................................................................................................................5.19
Create 3D Preset ............................................................................................................................5.20
Recall 3D Preset .............................................................................................................................5.20
continued 
						

							
Rev B September 2010 Page 5.3
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 5. Userware

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Global Colour page ..........................................................................................................................5.21
Global Colour Mode ........................................................................................................................5.21
Modal Colour page ...........................................................................................................................5.22
Modal Colour Mode .........................................................................................................................5.22
Lift and Gain sliders ........................................................................................................................5.23
Temperature slider ..........................................................................................................................5.23
Information page ...............................................................................................................................5.24
Projector Information .......................................................................................................................5.24
Digital Projection .............................................................................................................................5.24
FastFrame page ................................................................................................................................5.25
FastFrame Enable ..........................................................................................................................5.25
Dark Time ......................................................................................................................................5.25
System page ......................................................................................................................................5.26
OSD ..............................................................................................................................................5.26
Backlight ........................................................................................................................................5.26
DMD controls .................................................................................................................................5.26
Lamp mode ....................................................................................................................................5.26
Lamp Power slider ..........................................................................................................................5.26
Connect page .....................................................................................................................................5.27
Refresh ..........................................................................................................................................5.27
Connect .........................................................................................................................................5.27
Disconnect .....................................................................................................................................5.27 
						

							
Page 5.4  Rev B September 2010
5. Userware Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Notes
  To use the Titan Userware the 
java	runtime	Environment
 
software must be installed on 
your browser. This software can 
be downloaded, free of charge 
from www.java.com.
  The LAN IP Address of the 
projector can be found in the 
Network submenu of the Setup 
menu, as described in section 
4. Controlling the projector
.
  Whenever the projector is 
connected to mains power, 
whether in Running mode or 
Standby mode, the Applet 
version of the Userware will be 
available.
 The Applet version of the 
Userware can be used only to 
control the projector from which 
it was downloaded.
 The Userware can be used to 
control only one projector at a 
time, and only one instance can 
be running at one time.
  More than one computer can be 
used to control more than one 
projector on the same network.
Introduction
The Titan Userware provides an intuitive interface to enable control of many of the 
features of the projector from a personal computer, via a LAN connection.
There are two versions of the Userware: the Applet version, stored on the projector 
and the Standalone version, supplied on disk or from the Digital Projection website.
Applet version
To activate the Userware, simply point the browser at the projector by typing its 
LAN IP Address
 into the address bar, then press the Enter key.
The Applet version does not require installation on the personal computer, as it 
is in the form of a Java applet, downloaded automatically from the projector by 
the browser. The first time the applet is downloaded, you may see the following 
message:
Tick the box and click OK. In future, the Userware will load immediately.
The Userware interface is organised into a number of pages, as listed below:
Show  Lens    Blend   Image   Screen
MCGD  TCGD    3D   Global   Modal
info    FastFrame  System
Each page is described in full later in this section.
When the Userware is started, the Show page will display immediately. The Page 
buttons are always visible at the bottom of the display:
Disconnect
Navigate away from the projector to disconnect.
reconnect
To reconnect re-type the IP Address in the browser address box then press 
Return.
•
•
•
•
New Java applet download:
Tick the box only if you trust the source.
o  I trust this applet.         OK 
						

							
Rev B September 2010 Page 5.5
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 5. Userware

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Standalone version
To install the Userware, simply copy the file (from the CD, or downloaded from 
the Digital Projection website), to a folder on the computer.
Double click on the filename to start the software.
The Userware interface is organised into a number of pages, as listed below:
Show  Lens    Blend   Image   Screen
MCGD  TCGD    3D   Global   Modal
info    FastFrame  System   Connect
Each page is described in full later in this section.
When the Userware is started, the Show page will display immediately. The Page 
buttons are always visible at the bottom of the display:
Disconnect
To disconnect from the projector, go to the Connect page and click on 
Disconnect.
reconnect
To reconnect, go to the Connect page and click on Connect.
•
•
•
•
Notes
 To use the Titan Userware the 
java	runtime	Environment
 
software must be installed on 
your computer. This software 
can be downloaded, free of 
charge from www.java.com.
  The Userware can be used to 
control only one projector at a 
time, and only one instance can 
be running at one time.
  The 
Connect page can be 
used to switch control between 
multiple projectors. 
(see later in this section)
  More than one computer can be 
used to control more than one 
projector on the same network.
 The Connect page is described 
in more detail later in this 
section. 
						

							
Page 5.6  Rev B September 2010
5. Userware Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Show page
The Show page is the first to display when the browser connects to the projector .
To return to the Show page at any time, click on Show.
On	/	Off
Click On to switch the projector On.
Click Off to switch the projector into Standby mode.
Shutter	Open	/	Closed
Click on Shutter	Open to open the shutter.
Click on Shutter Close to close the shutter.
freeze	/	un-freeze
Click on freeze to freeze the display on the current frame.
Click on un-freeze to un-freeze the display.
Picture sliders
Use the sliders to adjust the Brightness, Contrast, Saturation, Hue and 
Sharpness of the display.
Click on the number above the slider to return to the default value.
•
•
•
•
•
•
•
•
•
Notes
 The  freeze function is NOT 
available for Input 8.
Picture 
sliders