Digital Projection Titan 1080p 3d, Dual 3d, Titan 1080p 3d, Dual 3d Ultra Contrast, Titan Dual Fastframe User Manual

							
Rev B September 2010 Page 7.5
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual  7. Appendix

Brightness
1080p 3D  4500 ANSI lumens  ±10%
1080p 3D Ultra Contrast  2500 ANSI lumens  ±10%
1080p Dual 3D  9000 ANSI lumens  ±10% in dual lamp mode
1080p Dual 3D Ultra Contrast  4500 ANSI lumens  ±10% in dual lamp mode
1080p Dual FastFrame  9000 ANSI lumens  ±10% in dual lamp mode
Colour temperature  Native: 7500°K (±1000°K), White balance adjustment: 3000°K - 10000°K
Electrical
Inputs  RGB1, RGB2, DVI-Single, SDI, Composite Video, S-Video, Component 
DVI-Single/Dual/Twin
Pixel clock  up to 165MHz
Control inputs  1 x 3D
  1 x LAN
  1 x wifi LAN
  1 x RS232 serial: 19200 baud, 8 bits, 1 stop bit, no parity
  1 x remote control
Indicators  Input, 3D sync Power, Shutter, Error, IR, Lamp 1, Lamp 2
Mains supply
Single  580W, 100-240VAC ±10%, 48-62Hz (single phase)
Dual  910W, 100-240VAC ±10%, 48-62Hz (single phase)
International Regulations Meets FCC Class A  requirements 
Meets EMC Directives (EN 55022, EN 55024, EN 55103) 
Meets Low Voltage Directive (EN60950)
Physical
Operating	Temperature  0 to 40°C
Storage Temperature  -10 to 50°C
Thermal Dissipation
Single  1770 BTU/hr
Dual  2777 BTU/hr
Operating	humidity   20%  to 80% non-condensing
Weight  approximately 31 kg (68 lbs)
FCC WIFI ID
R68WIPORT
 Specifications are subject to change without notice. 
						

							
Page 7.6  Rev B September 2010
7. Appendix  Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

Lens Data
Optical105-607 ~ 107-195105-608105-609109-236 ~ 109-359105-610 ~ 107-196
throw ratio 0.67	:	1	fixed1.12	:	1	fixed1.12	:	1	fixed1.16	-	1.49	:1	zoom 1.39	-	1.87	:	1	zoom
full DMD image width0.67 : 1
1.64 - 4.78m
(5.4 - 15.7ft)
1.12 : 1 
2.68 - 13.39m
(8.8 - 43.9ft)
1.12 : 1
1.07 - 1.79m
(3.5 - 5.9ft)
1.16 : 1
2.59 - 12.93m
(8.5 - 42.4ft)
1.49 : 1
2.01 - 10.07m
(6.6 - 33ft)
1.39 : 1
2.88 - 17.27m
(9.4 - 56.7ft)
1.87 : 1
2.14 - 12.83m
(7 - 42.1ft)
throw distance0.67 : 1
1.1 - 3.2m
(3.6 - 10.5ft)
1.12 : 1 
3 - 15m
(9.8 - 49.2ft)
1.12 : 1
1.2 - 2m
(3.9 - 6.6ft)
1.16 : 1
3 - 15m
(9.8 - 49.2ft)
1.49 : 1
3 - 15m
(9.8 - 49.2ft)
1.39 : 1
4 - 24m
(13.1 - 78.7ft)
1.87 : 1
4 - 24m
(13.1 - 78.7ft)
lens shift vertical *
pixels (vs DMD height)
± 108
(±  0.1H)
+ 756, - 540
(+ 0.7,  0.5H)
+ 756, - 540
(+ 0.7,  0.5H)
± 540
(±  0.5H)
+ 756, - 540
(+ 0.7,  0.5H)
lens shift horizontal *
pixels (vs DMD width)
± 192
(±  0.1W)
± 345
(±  0.18W)
± 345
(±  0.18W)
± 345
(±  0.18W)
± 345
(±  0.18W)
ApertureF/2.5F/2.5F/2.5F/2.5F/2.5
Max object field size26.1mm
(1.03”)
34.6mm
(1.36”)
34.6mm
(1.36”)
31.4 mm
(1.24”)
34.6 mm
(1.36”)
Effective focal length14.6mm
(0.58”)
23.55mm
(0.93”)
23.55mm
(0.93”)
24.18 - 31.06 mm
(0.95 - 1.22 in)
28.94 - 38.95mm
(1.14 - 1.53 in)
Distortion88%
Mechanical
Lens extension** 
(±2%)
204 mm
(8.0 in)
268 mm
(10.6 in)
268 mm
(10.6 in)
226 mm
(8.9 in)
194 mm
(7.6 in)
Length361 mm
(14.2 in)
422 mm
(16.6 in)
422 mm
(16.6 in)
378 mm
(14.9 in)
345 mm
(13.6 in)
Maximum diameter163
(6.4 in)
169 mm
(6.7 in)
169 mm
(6.7 in)
139 mm
(5.5 in)
139 mm
(5.5 in)
Weight
±0.05 kg (±0.1lb)
5.40 kg
(11.9 lb)
5.85 kg
(12.9 lb)
5.85 kg
(12.9 lb)
to be confirmed6.10 kg
(13.4 lb)
lens extension, measured from 
front of corner post* Actual available lens shift is reduced when the lens is to be sh ifted 
in two directions combined (see Shifting the image, in section 
2. Installation
).
**  Lens extension is the distance from the outer end of the lens to the 
front of the projector. It is important for calculating throw distance 
accurately (see Useful lens calculations, in section 2. Installation). 
						

							
Rev B September 2010 Page 7.7
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual  7. Appendix

Optical105-611 ~ 107-197105-612 ~ 107-198105-613 ~ 107-199109-235 ~ 109-358
throw ratio1.87	-	2.56	:	1	zoom2.56	-	4.16	:	1	zoom4.16	-	6.96	:	1	zoom6.92	-	10.36	:	1	zoom
full DMD image width1.87 : 1
2.14 - 12.83m
(7 - 42.1ft)
2.56 : 1
1.56 - 9.38m
(5.1 - 30.8ft)
2.56 : 1
3.55 - 17.58m
(11.6 - 57.7ft)
4.16 : 1
2.19 - 10.82m
(7.2 - 35.5ft)
4.16 : 1
2.88 - 19.23m
(9.4 - 63.1ft)
6.96 : 1
1.72 - 11.49m
(5.6 - 37.7ft)
6.92 : 1
1.73 - 11.56m
(5.7 - 37.9ft)
10.36 : 1
1.16 - 7.72m
(3.8 - 25.3ft)
throw distance1.87 : 1
4 - 24m
(13.1 - 78.7ft)
2.56 : 1
4 - 24m
(13.1 - 78.7ft))
2.56 : 1
9.1 - 45m
(29.9 - 147.6ft)
4.16 : 1
9.1 - 45m
(29.9 - 147.6ft)
4.16 : 1
12 - 80m
(39.4 - 262.5ft)
6.96 : 1
12 - 80m
(39.4 - 262.5ft)
6.92 : 1
12 - 80m
(39.4 - 262.5ft)
10.36 : 1
12 - 80m
(39.4 - 262.5ft)
lens shift vertical *
pixels (vs DMD height)
+ 756, - 540
(+ 0.7,  0.5H)
+ 756, - 540
(+ 0.7,  0.5H)
+ 756, - 540
(+ 0.7,  0.5H)
+ 756, - 540
(+ 0.7,  0.5H)
lens shift horizontal *
pixels (vs DMD width)
± 345
(±  0.18W)
± 345
(±  0.18W)
± 345
(±  0.18W)
± 345
(±  0.18W)
ApertureF/2.5F/2.5F/2.5F/2.5
Max object field size34.6 mm
(1.36”)
34.6 mm
(1.36”)
34.6 mm
(1.36”)
34.6 mm
(1.36”)
Effective focal length39.0 - 53.43mm
(1.54 - 2.1 in)
52.4 - 85.3mm
(2.06 - 3.36 in)
84.86 - 142.03mm
(3.34 - 5.59 in)
141.2 - 211.4
(5.56 - 8.32 in)
Distortion88%
Mechanical
Lens extension**
(±2%)
159 mm
(6.3 in)
145 mm
(5.7 in)
129 mm
(5.1 in)
179 mm
(7.0 in)
Length311 mm
(12.2 in)
304 mm
(12.0 in)
271 mm
(10.7 in)
340 mm
(13.4 in)
Maximum diameter139 mm
(5.5 in)
139 mm
(5.5 in)
139 mm
(5.5 in)
139 mm
(5.5 in)
Weight5.15 kg
(11.3 lb)
5.25 kg
(11.6 lb)
4.70 kg
(10.3 lb)
to be confirmed
* Actual available lens shift is reduced when the lens is to be sh ifted 
in two directions combined (see Shifting the image, in section 
2. Installation
).
**  Lens extension is the distance from the outer end of the lens to the 
front of the projector. It is important for calculating throw distance 
accurately (see Useful lens calculations, in section 2. Installation).
lens extension, measured from 
front of corner post 
						

							
Page 7.8  Rev B September 2010
7. Appendix  Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

Dimensions
All dimensions in mm 
unless otherwise stated 
						

							
Rev B September 2010 Page 7.9
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual  7. Appendix

Input modes supported
SignalResolutionRefresh Rate 
(	hz	)Total number of lines horizontal	
 Frequency 
(khz)
COmPOSiTE
S-ViDEO
CO mPONENT
RGB1
 
RGB2DVISDI 
**
SDTV480i720 x 4806052515.73üüüü
576i720 x 5765062515.63üüüü
HDTV 480p720 x 4806052531.51üü
576p720 x 5765062531.25üü
720p501280 x 7205075037.51üüü
720p601280 x 7206075045.00üüü
1080psf241920 x 108048112527.00üüü
1080p241920 x 108024112527.00üüü
1080i501920 x 108050112528.13üüü
1080p251920 x 108025112528.13üüü
1080i601920 x 108060112533.75üüü
1080p301920 x 108030112533.75üüü
1080p501920 x 108050112556.24ü *ü *
1080p601920 x 108060112567.48ü *ü *
COMPUTER480p640 x 4806052531.51üü
VGA72640 x 4807252037.86üü
VGA75640 x 4807550037.51üü
VGA85640 x 4808550943.27üü
WVGA60848 x 4806051731.02üü
SVGA56800 x 6005662535.16üü
SVGA60800 x 6006062837.89üü
SVGA72800 x 6007266648.08üü
SVGA75800 x 6007562546.88üü
SVGA85800 x 6008563153.68üü
XGA601024 x 7686080648.38üü
XGA701024 x 7687080656.50üü
XGA751024 x 7687580060.02üü
XGA851024 x 7688580868.68üü
XGA+751152 x 8647590067.52üü
WXGA601280 x 7686079847.78üü
WXGA601280 x 8006083149.70üü
WXGA601280 x 9606083149.70üü
WXGA601360 x 7686079847.72üü
WXGA+601440 x 9006093455.94üü
SXGA-601280 x 96060100060.02üü
SXGA-851280 x 96085101185.98üü
SXGA601280 x 102460106664.02üü
SXGA751280 x 102475107280.32üü
SXGA851280 x 102485107291.16üü
SXGA+601400 x 105060108965.32üü
SXGA+751400 x 105075109982.30üü
SXGA+851400 x 105085110593.90üü
UXGA601600 x 12006012575.02üü
VESA1080p1920 x 108060112067.16ü *ü *
* RGB colourspace only 
** SDI not present on earlier models 
						

							
Page 7.10  Rev B September 2010
7. Appendix  Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

Notes
 To select the sync format for 
RGB signals, see Setup Menu, 
in 4.Controlling the Projector.
Input connections
1. RGB1 input
5 x 75 ohm BNC
Used for computer, progressive video and analog HD video.
rgsB	 	 rgBS	 	rgBhV	 	 YPrPb
R      R   R   Pr/Cr
G + Sync  G   G   Y
B      B   B   Pb/Cb
      Sync   H Sync
          V Sync
2. RGB2 input
15 way D-type connector
1 R
2  G
3  B
4  unused 
5  Digital Ground (H Sync)
6  R Ground
7  B Ground
8  G Ground
9  +5v
10  Digital Ground (V Sync/DDC)
11  unused
12  SDA
13  H Sync
14  V Sync
15  SCL
pin view of female connector 
						

							
Rev B September 2010 Page 7.11
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual  7. Appendix

3. DVI-D Single input
24 way D-type connector
1 TMDS Data 2-
2  TMDS Data 2+
3  TMDS Data 2 Shield
4  unused
5  unused
6  DDC Clock
7  DDC Data
8  unused
9  TMDS Data 1-
10  TMDS Data 1+
11  TMDS Data 1 Shield
12  unused
13  unused
14  +5 V Power
15  Ground
16  Hot Plug Detect*
17  TMDS Data 0-
18  TMDS Data 0+
19  TMDS Data 0+
20  TMDS Data 0 Shield
21  unused
22  unused
23  TMDS Clock Shield
24  TMDS Clock+
*  Hot plug detect (HPD) is fully DVI compliant.  DVI sources detect the presence 
of a display device by providing +5V on pin 14 and looking for +5V on pin 16. 
Whenever the projector is operational, and 5V is present on pin 14, pin 16 will be 
held at +5V.
EDID is available even when the projector is switched off.
Operational means that the projector is powered up.  Non operational states are 
powered down and some self test and reprogramming modes.
High Definition Content Protection (HDCP) is supported on this input.
Notes
pin view of female connector 
						

							
Page 7.12  Rev B September 2010
7. Appendix  Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

4. SDI input
1 x 75 ohm BNC
SMPTE 292 / HD-SDI signals are very high speed digital signals which require 
better quality coaxial cable than conventional analogue video. The data rate is 1.5 
Gigabits per second.
In choosing cable length and connectors for any installation the frequency response 
loss in decibels should be proportional to 1Öf, from 1MHz, to 1.5GHz.  The following 
or similar cable specification should be used to ensure fault free communication 
between source and projector:
Belden 8281 cable or equivalent
5. Composite video input
1 x 75 ohm BNC
PAL or NTSC video
6. S-Video input
4 pin mini-DIN
1 Y Ground
2  C Ground
3  Luminance (Y)
4  Chrominance (C)
7. Component video input
4 x 75 ohm BNC
Used for standard definition interlaced signals only
rgsB	 	 rgBS	 	 YPrPb
R      R   Pr/Cr
G + Sync  G   Y + Sync
B      B   Pb/Cb
      Sync
Notes
 To select the sync format for 
RGB signals, see Setup Menu, 
in 4.Controlling the Projector.
  To select between RGB and 
YPrPb signals, see Colour 
Menu, in 4.Controlling the 
Projector.
pin view of female connector 
						

							
Rev B September 2010 Page 7.13
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual  7. Appendix

8. DVI-D Single/Dual/Twin input
24 way D-type connector
1 TMDS Data 2-
2  TMDS Data 2+
3  TMDS Data 2/4 Shield
4  TMDS Data 4-
5  TMDS Data 4+
6  DDC Clock
7  DDC Data
8  unused
9  TMDS Data 1-
10  TMDS Data 1+
11  TMDS Data 1/3 Shield
12  TMDS Data 3-
13  TMDS Data 3+
14  +5 V Power
15  Ground
16  Hot Plug Detect*
17  TMDS Data 0-
18  TMDS Data 0+
19  TMDS Data 0+
20  TMDS Data 0/5 Shield
21  TMDS Data 5 -
22  TMDS Data 5+
23  TMDS Clock Shield
24  TMDS Clock+
*  Hot plug detect (HPD) is fully DVI compliant.  DVI sources detect the presence 
of a display device by providing +5V on pin 14 and looking for +5V on pin 16. 
Whenever the projector is operational, and 5V is present on pin 14, pin 16 will be 
held at +5V.
EDID is available even when the projector is switched off.
Operational means that the projector is powered up.  Non operational states are 
powered down and some self test and reprogramming modes.
High Definition Content Protection (HDCP) is supported on this input.
Notes
 For important information about 
how Input 8 is used, see INPUT 
8 in the Notes column, and also 
Section	4,	Overview
.
  Input 8 may not be present on 
some models
pin view of female connector 
						

							
Page 7.14  Rev B September 2010
7. Appendix  Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

Control connections
Wired Remote control connection
3.5mm mini jack
Tip  Power
Ring  Signal
Sleeve  Ground
LAN connection
TCP Port number 
10001
Wireless 
802.11b/g 
10BaseT Unshielded Twisted Pair cable
The standard wire colours as as follows:
1 White / Orange stripe
2  Orange
3  White / Green stripe
4  Blue
5  White / Blue stripe
6  Green
7  White / Brown stripe
8  Brown
Crossed cable
(used to connect directly to a computer with no hub or network.) 
(Note that only the green and orange pairs are crossed)
1 White / Orange stripe    White / Green stripe 1
2  Orange      Green     2
3  White / Green stripe    White / Orange stripe 3
4  Blue        Blue     4
5  White / Blue stripe    White / Blue stripe 5
6  Green      Orange     6
7  White / Brown stripe    White / Brown stripe 7
8  Brown      Brown     8
Notes
 Note that plugging in the remote 
control cable will disable the 
infra-red.
 Use:
a straight cable to connect to a 
hub or network, or
a crossed cable as shown here 
to connect ONLY to a computer 
directly.
 Only one remote connection 
(RS232, LAN or Wireless LAN) 
should be used at any one time.
•
•top view of cable connector 
(clip is underneath)
Sleeve
Ring
Tip