Digital Projection Titan 1080p 3d, Dual 3d, Titan 1080p 3d, Dual 3d Ultra Contrast, Titan Dual Fastframe User Manual

							
Rev B September 2010 Page 5.7
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 5. Userware

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Input Presets
recall
To recall a set of modal and lens* settings that have been saved:
Click on Preset, and select one of the Presets A - S, from the drop down menu.
Click on Recall.
  The projector will switch to the saved input source, and redetect  the input mode 
before applying the saved modal and lens* settings.
Save
To save the current input source, mode, modal and lens* settings:
Click on Preset, and select one of the Presets A - S, from the drop down menu.
Click on Save.
  The settings will be saved to the selected preset.
•
•
•
•
Notes
  For more information about 
input modes and input presets, 
see Overview, in section 
4. Controlling the Projector
.
  A preset can be applied only to 
the same mode for which it was 
created. If the detected input 
mode does not match, then 
settings from the mode history 
or mode library will be applied 
instead.
  For more information about 
input modes, see Overview, 
in section  4. Controlling the 
Projector.
 The lens settings, ie Focus 
position, Zoom position and 
Shift, are included only for the 
first ten presets.
 Presets can also be deleted: 
see Input menu, in section 
4. Controlling the Projector
.
Show page continued
Preset 
						

							
Page 5.8  Rev B September 2010
5. Userware Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Orientation
Click on Orientation to select from the drop down menu.
Input
Click on Input to select from the drop down menu.
Test Pattern
Click on Test Pattern to select from the drop down menu.
Aspect Ratio
Click on Aspect Ratio to select from the drop down menu.
•
•
•
•
Notes
  For more information about 
input modes, see Overview, 
in section  4. Controlling the 
Projector.
 Input 8 and 3D may not be 
present on some models
 The signal from input 8 will 
be displayed in 3D, only if 3D 
Enable is set to on: see 3D 
Menu, later in this section.
 For more information about 
test patterns, see Setup menu, 
in section  4. Controlling the 
Projector.
 For more information about 
aspect ratios, see Picture 
menu and Geometry menu, 
in section  4. Controlling the 
Projector.
Show page continued
Orientation
Input
Test 
PatternAspect 
Ratio 
						

							
Rev B September 2010 Page 5.9
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 5. Userware

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Notes
 Each time a new lens is 
fitted	to	the	projector,	
the calibration procedure 
must be carried out. See 
Setup menu, in Section 4. 
Controlling the projector.
Lens page
To see the Lens page, click on Lens.
Lens controls
Click on the buttons to Move, Focus and Zoom the lens.
Click on  to centre the lens.
Shutter	Open	/	Closed
Click on  Open	Shutter to open the shutter.
Click on Close Shutter to close the shutter.
Calibrate Focus
Click on Calibrate Focus to calibrate the lens focus mechanism.
Calibrate Zoom
Click on Calibrate Zoom to calibrate the lens zoom mechanism.
•
•
•
•
•
•
•
Lens 
controls 
						

							
Page 5.10  Rev B September 2010
5. Userware Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Notes
  For more information about 
Edge Blend, see Setup menu, 
in Section 4. Controlling the 
projector.
Edge Blend page
To see the Edge Blend page, click on Blend.
markers	On	/	Off
Click on  markers	On to display the overlap markers.
Click on markers	Off	to remove the overlap markers.
Active Edges
Click on Top, Bottom, Left or Right to enable or disable the blend for each 
edge.
Input 8 DVI 3D Resolution
Click on Input 8 DVI 3D Resolution to select from the drop down menu.
Overlap	w idth
Use the sliders to adjust the  Overlap	width for each edge.
•
•
•
•
•
• 
						

							
Rev B September 2010 Page 5.11
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 5. Userware

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Notes
  For more information about 
Black Level Uplift, see 
Setup menu, in Section 4. 
Controlling the projector.
 Non-Addressable Border 
should always be set to 
Manual.
Black Level Uplift page
To see this page, click on Black Level Uplift on the Edge Blend page.
x2, x4 Region Uplift
Use the sliders to adjust the amount of Uplift for each region.
Non-Addressable Border
Click on Non-Addressable Border to select from the drop down menu.
Use the sliders to adjust the size of the Non-Addressable Border for each 
edge.
Back to Edge Blend
Click on Back to Edge Blend to return to the Edge Blend page.
•
•
•
•
•
Border 
controls
Edge Blend page continued 
						

							
Page 5.12  Rev B September 2010
5. Userware Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Notes
 Changing the Colour Space 
on this page manually 
overrides the colour space 
for analogue component 
inputs, which may result in an 
incorrectly displayed image.
  The Component selection is 
available for the Component 
input only.
 For more information about 
phase, see Picture menu and 
Geometry menu, in section 
4. Controlling the Projector
.
  The Phase slider is available for 
RGB1 and RGB2 inputs only.
 For more information about 
Gamma, see Picture menu, 
in section  4. Controlling the 
Projector.
 User download of Gamma 
correction tables is not yet 
available.
 The Parametric slider is 
available only when Parametric 
is selected in Gamma 
Correction.
Image page
To see the Image page, click on Image.
Colour Space
Click on Colour Space to select from the drop down menu.
Component
Click on Component to select from the drop down menu.
Phase slider
Use the slider to adjust the Phase.
Gamma
Click on Gamma Correction to select from the drop down menu:
Parametric slider
Use the slider to adjust the Gamma manually.
•
•
•
•
•
•
Component
Phase 
slider
Colour 
Space
Parametric 
slider
Gamma 
Correction 
						

							
Rev B September 2010 Page 5.13
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 5. Userware

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Notes
  The Convergence controls 
open in a new window, to allow 
you to visit the Show page, in 
order to display a Test Pattern.
Convergence controls
To see these controls, click on Convergence on the Image page.
The Convergence controls open in a new window.
horizontal	Convergence
Use the sliders to adjust the position of the Blue and Green components of the 
image relative to the Red component.
Vertical Convergence
Use the sliders to adjust the position of the Blue and Green components of the 
image relative to the Red component.
Close
Click on Close to close the Convergence controls window.
•
•
•
•
Image page continued 
						

							
Page 5.14  Rev B September 2010
5. Userware Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Notes
  The blanking curtains will not 
applied until Blanking is turned 
On.
 For more information about 
blanking, see Geometry menu, 
in section  4. Controlling the 
Projector.
 For more information about 
keystone adjustment, see 
Geometry menu, in section 
4. Controlling the Projector
.
Screen page
To see the Screen page, click on Screen.
Blanking	On	/	Off
Click on Enable to turn the blanking On  or Off .
Blanking adjust
Use the sliders to adjust the Top, Bottom, Left and Right blanking curtains.
Keystone adjust
Use the slider to adjust the Keystone setting.
Position adjust
Use the sliders to adjust the  horizontal and Vertical position of the image.
•
•
•
•
• 
						

							
Rev B September 2010 Page 5.15
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 5. Userware

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Notes
 Read the notes on MCGD, 
TCGD and ColorMAX below, 
before making any MCGD 
settings.
MCGD page
MCGD - Measured Colour Gamut Data - can be used to correct for a number of 
environmental variables, for example:
two or more different projectors
lamp age
different lenses
ambient light
screen characteristics
The MCGD measurement procedure
1   On the Show page, select the ColorMAX test pattern.
2  Using a photo-spectrometer, measure the following values:
  White  x y
3  On the System page, switch off the Green and Blue DMDs.
4  Using a photo-spectrometer, measure the following values:
  Red    x y
5  Repeat for the Green and Blue x and y values.
6  Enter all the values into the MCGD page, as described on the next page.
  Notes on MCGD, TCGD and ColorMAX User settings
TCGD (see the next section)
The parameters entered on the TCGD page establish the target settings that the 
projector needs to aim for, in order to give a specified colour gamut.
MCGD (see this section)
The parameters entered on the MCGD page establish the starting settings, from 
which the projector will calculate what adjustments are necessary to achieve the 
color gamut specified on the TCGD page.
Only one set of MCGD data can be stored on the projector, but many more can be 
stored on a computer, and retrieved using the MCGD page controls.
ColorMAX User settings
Only two sets of color gamut parameters can be stored on the projector -  
ColorMAX User 1 and ColorMAX User 2 - but many more can be stored on a 
computer, and retrieved using the TCGD page controls. 
						

							
Page 5.16  Rev B September 2010
5. Userware Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

To see the MCGD page, click on MCGD .
On first entering the MCGD screen, the MCGD values will show those currently 
loaded into the projector.
MCGD edit boxes
Click on each box in turn, and enter the measured x and y values for each 
colour.
Write to Projector
Click on Write to Projector to save the values in the edit boxes to the projector.
Read from Projector
Click on Read from Projector to copy the values from the projector into the edit 
boxes.
As the MCGD values are edited, the values in the white box remain unaltered.
Save File
Click on Save to save the values in the edit boxes to an  mCgD	file on the 
computer.
 When prompted, enter a filename or browse to an existing file that is to be 
overwritten.
Open	file
To retrieve a set of saved MCGD values from the computer, click on Open.
  When prompted, enter a filename or browse to the file that is to b e opened.
•
•
•
•
•
•
Notes
 Read the notes on MCGD, 
TCGD and ColorMAX earlier 
in this section before making 
any MCGD settings.
  1. New MCGD values will not 
be downloaded to the projector 
until the Write to Projector 
button is pressed.
  2. The values will not be used 
until the ColorMAX User 1 or 
ColorMAX User 2 is chosen 
in the Colour or Global 
Colourimetry menus.
  3. If one of the User settings is 
already in use, then it will be 
necessary to re-apply it before 
any change is seen.
 These values establish the 
starting settings, from which 
the projector will calculate what 
adjustments are necessary 
to achieve the color gamut 
specified on the TCGD page.
.
 MCGD files are named 
filename.mcgd.
MCGD page continued
MCGD 
edit 
boxes