Digital Projection Titan 1080p 3d, Dual 3d, Titan 1080p 3d, Dual 3d Ultra Contrast, Titan Dual Fastframe User Manual

							
Rev B September 2010 Page 5.27
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 5. Userware

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview.

Notes
  The Connect page is available 
only on the Standalone version 
of the Userware.
 The Userware can be used to 
control only one projector at a 
time, and only one instance can 
be running at one time.
  The 
Connect page can be 
used to switch control between 
multiple projectors.
  More than one computer can be 
used to control more than one 
projector on the same network.
Connect page
To see the Connect page, click on Connect.
Refresh
Click on Refresh to search the network for projectors.
  Any projectors previously connected, that are now no longer onli ne, will be 
marked Unreachable.
Connect
To connect to a projector, click on one of the LAN IP addresses in the list, then 
click on Connect.
or Double click on a LAN IP address.
Any projector previously connected will be disconnected, and the Userware will 
connect to the new projector.
 The 
LAN IP address of the projector that is connected will be highlighted.
 Projector Connected will be shown at the top left of all pages, together with the 
projector’s Serial No and Model.
Disconnect
To disconnect from the projector, click on Disconnect
 Projector Disconnected will be shown at the top left.
•
•
•
• 
						

							
Page 5.28  Rev B September 2010
5. Userware Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section	4, 	Overview. 
						

							
Rev B September 2010 Page 6.1
6. Maintenance
Contents
Changing the lamp module ..............................................................................................................6.2
Changing	the	air	filters ......................................................................................................................6.2
Cleaning ................................................................................................................................................6.3
Projector ..........................................................................................................................................6.3
Lens ................................................................................................................................................6.3 
						

							
Page 6.2  Rev B September 2010
6. Maintenance  Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

Changing	the	air	filters
The air filters should be changed only by qualified and authorised service 
personnel.
Contact your Digital Projection Dealer.
•
•
Changing the lamp module
The lamp module should be changed only by qualified and authorised service 
personnel.
Contact your Digital Projection Dealer.
•
•
Notes
	 The	lamp	and	filters	in	this	
projector should be changed 
ONLY	by	authorised	and	
qualified	service	personnel.
  Always allow the lamp to cool 
for 5 minutes before: 
- disconnecting the power 
- moving the projector.
  At the end of life, the lamp 
will not strike, and the Lamp 
Indicator on the control panel 
will show red. (Typical lamp life 
is 2000 hours)
 Do not use the lamp for more 
than 2000 hours, as this may 
cause serious lamp failure, 
damage the lamp module 
and cause extra cost on 
replacement. 
 HID lamps produce high 
intensity light. Do not look 
directly at the light coming 
from the lamp housing or the 
lens.
  The filters should be changed 
at the same time as the lamp is 
changed.
 The air filters should be 
changed regularly:
  - In a clean environment such 
as an office, change after 2000 
hours, at the same time as the 
lamp is changed.
  - In a dusty or smoky 
environment such as a theatre 
or public area, more frequent 
changes may be necessary. 
						

							
Rev B September 2010 Page 6.3
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual  6. Maintenance

Notes
 Always allow the lamp to cool 
for 5 minutes before:
 - disconnecting the power 
- moving the projector.
 Never use strong detergents 
or solvents such as alcohol 
or thinners to clean the 
projector and lens.
Cleaning
Turn the projector off before cleaning.
Projector
Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild 
detergent.
Lens
Use a blower or lens paper to clean the lens, taking care not to scratch the glass. 
						

							
Page 6.4  Rev B September 2010
6. Maintenance  Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 
						

							
Rev B September 2010 Page 7.1
7. Appendix
Contents
Troubleshooting ..................................................................................................................................7.2
Specifications ......................................................................................................................................7.4
Part numbers ....................................................................................................................................7.4
Optical .............................................................................................................................................7.4
Electrical ..........................................................................................................................................7.5
Physical ...........................................................................................................................................7.5
Lens Data ........................................................................................................................................7.6
Dimensions ..........................................................................................................................................7.8
Input modes supported .....................................................................................................................7.9
Input connections .............................................................................................................................7.10
1. RGB1 input .................................................................................................................................7.10
2. RGB2 input .................................................................................................................................7.10
3. DVI-D Single input ........................................................................................................................7.11
4. SDI input ....................................................................................................................................7.12
5. Composite video input .................................................................................................................7.12
6. S-Video input ..............................................................................................................................7.12
7. Component video input ................................................................................................................7.12
8. DVI-D Single/Dual/Twin input .......................................................................................................7.13
Control connections ........................................................................................................................7.14
Wired Remote control connection .....................................................................................................7.14
LAN connection ..............................................................................................................................7.14
Crossed cable ..............................................................................................................................7.14
3D sync .........................................................................................................................................7.15
Serial control input ..........................................................................................................................7.15
Null-modem cable .........................................................................................................................7.15
Serial port settings ........................................................................................................................7.15
Remote communications protocol ...............................................................................................7.16
Introduction ....................................................................................................................................7.16
Message Structure ..........................................................................................................................7.16
Operation Messages .....................................................................................................................7.17
Enhanced Messages .....................................................................................................................7.18
Operation Command examples ........................................................................................................7.19
Power  (0102) .............................................................................................................................7.19
Source  (3702) ............................................................................................................................7.20
Brightness (E502) ........................................................................................................................7.21
Contrast (E602) ...........................................................................................................................7.22
Shutter  (CF02) ...........................................................................................................................7.23
Quick Reference chart .....................................................................................................................7.24 
						

							
Page 7.2  Rev B September 2010
7. Appendix  Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

Troubleshooting
problem possible solutions
The projector will not power up.Check that the mains plug is plugged in and that the mains supply is swi\
tched on.
Check any external fuses or breakers.
The projector shuts down after it has been in use for some time.The projector may be overheating. Check that the air inlets and outlets are clear of any obstruction. Check that the air filter is clean, and if it is dirty , fit a new one.
See section 1. Introduction, Getting to know the projector
No image is displayed.Check the lamp indicators on the control panel. If both indicators are red, then both lamps are faulty.
See section 5. Maintenance, Changing the lamp
Check that the input source is switched on and connected to the projector correctly.
Check that the correct image source is selected.
See section 4. Controlling the projector, Using the control keys and Input menu
Check that the brightness and contrast settings are set correctly.
See section 4. Controlling the projector, Picture menu
The projector may be overheating. Check that the air inlets and outlets are clear of any obstruction. Check that the air filter is clean, and if it is dirty, fit a new one.
The	image	does	not	fit	the	screen	
correctly.Check that the correct lens is being used for the combination of screen size and projection distance, and that the zoom is adjusted correctly.
See section 2. Installation, Choosing a lens
Check the image size settings.
See section 4. Controlling the projector, Picture or Geometry menus
Uneven image quality.Check that the projector is parallel to the screen.
Check that the screen is flat, and securely mounted.
Low image brightness.Check that the FastFrame Dark Time is not set too high.
See section 4. Controlling the projector, Setup menu
Poor colour depth reproduction.Colour depth is 8 bits using Single or Dual DVI inputs. If using  Twin DVI inputs for greater colour depth, check that both source cables are connected correctly .
If using 3D mode, check the settings of the Dark Time and Sync Delay controls.
See section 4. Controlling the projector, Setup menu 
						

							
Rev B September 2010 Page 7.3
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual  7. Appendix

problem possible solutions
Severe	flicker	or	motion	artifactsIf not using a 3D signal, check that 3D Enable is turned Off,
See section 4. Controlling the projector, Setup menu
3D images swappedCheck that Left/Right swap is selected correctly in the 3D server .
Check the Frame Dominance and Sync Delay settings in the 3D menu.
Check the Sync Source setting in the 3D menu.
See Section 4. Controlling the projector, Setup menu.
3D image ghostingCheck the Dark Time and Sync Delay settings in the 3D menu.
See Section 4. Controlling the projector, Setup menu.
No	OSD	(on-screen-display)	visible	
Check the OSD On button on the remote control or keypad has been pressed.
The OSD does not work when Input 8 is selected.
See Section 4. Controlling the projector, Controlling the projector when Input 8 is being used.
Projector does not respond to control commands from a computer.Check that the LAN or serial cable is connected correctly.
See this section 7. Appendix, Connections
If using a LAN, check that the address setting is made correctly .
See section 4. Controlling the projector, Network menu
If using a serial cable, check that the baud rate is set correctly.
See this section 7. Appendix, Connections
Check that the correct control codes are being used.
See Serial communications protocol (available from Digital Projection)
Projector does not respond to control 
commands from the remote control.
If you are using a cable, check that the cable is connected properly at both ends, 
that the cable is not damaged and that the cable is no longer than 50m (150ft).
If you are not using a cable, check that the infra red windows at the front and rear of the projector are not obstructed. Check that the cable is disconnected from the projector, as this disables the infra red. Check that the batteries are in good condition.
Check that the address setting on the remote control is set either to zero, or to the same as the projector.
See section 4. Controlling the projector, Communication menu
In the event that this troubleshooting guide has not solved the problem,\
 then contact your Digital Projection dealer or service centre. 
						

							
Page 7.4  Rev B September 2010
7. Appendix  Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual

Specifications
Part numbers
Projector
1080p 3D  109-583
1080p 3D Ultra Contrast  109-322
1080p Dual 3D  109-323
1080p Dual 3D Ultra Contrast  109-324
1080p Dual Fast Frame  109-362
Rigging frame  107-956
Power cable 10A, Europe  102-163
Power cable 13A, North America  102-165
Power cable 10A, United Kingdom  102-180
Remote control  105-023
4x AAA batteries  105-922
3D Sync cable  109-697
Lens clamp  111-256
User manual on CD  105-923
Important Information  108-467
Lenses High Brightness High Contrast
0.67 : 1 fixed lens  105-607 107-195
1.12 : 1 fixed lens (3 - 15m)  105-608 105-608
1.12 : 1 fixed lens (1.2 - 2m)  105-609 105-609
1.16 - 1.49 : 1 zoom lens  109 236 109-359
1.39 - 1.87 : 1 zoom lens  105-610 107-196
1.87 - 2.56 : 1 zoom lens  105-611 107-197
2.56 - 4.16 : 1 zoom lens  105-612 107-198
4.16 - 6.96 : 1 zoom lens  105-613 107-199
6.92 - 10.36 : 1 zoom lens  109-235 109-358
Optical
Digital Light Processor  3 x 0.95” Texas Instruments DMD™, resolution 1920 x 1080 pixels
Contrast Ratio
1080p 3D, Dual 3D  2000:1 full field (±10%)
1080p 3D, Dual 3D Ultra Contrast  5000:1 full field (±10%)
1080p Dual Fastframe  2000:1 full field (±10%)
Pixel	fill	factor   87%
Lamp life (typical)  2000 hours per lamp