Digital Projection Projector HIGHlite Laser II 3D Series User Manual

page 13
Installation and Quick-Start Guide
CHANGING THE LENS
Changing The Lens
The lens hood
There are two types of lens hood, short and long. 
The short lens hood is used with the following lenses:
Throw ratiosPart number
0.77 : 1 fixed lens110-808
1.16 : 1 fixed lens110-809
1.45 - 1.74 : 1 zoom lens110-803
1.74 - 2.17 : 1 zoom lens112-878
2.17 - 2.90 : 1 zoom lens113-852
2.90 - 4.34 : 1 zoom lens110-806
The long lens hood must be used with the following long throw lens:
Throw ratiosPart number
4.34 -...

page 14
Installation and Quick-Start Guide
CHANGING THE LENS
Inserting a new lens
1. Insert the lens into the lens aperture, making sure that the plug on the\
 zoom drive 
mechanism lines up with socket on the right of the lens aperture.
2. Rotate the lens clockwise until it clicks into place.
3. Secure the lens hood to the front of the projector with the screws.
Notes
 Before changing the lens, 
always make sure the projector 
is switched off and fully 
disconnected from its power 
supply.
 When...

page 15
Installation and Quick-Start Guide
CHANGING THE LENS
Removing the lens
1. Loosen the four screws securing the lens hood to the body of the project\
or. 
Remove the lens hood.
2. Push down the lens holder tab.
3. Rotate the lens anti-clockwise.
4. Pull the lens forward to remove it from the lens aperture.
Notes
 Before changing the lens, 
always make sure the projector 
is switched off and fully 
disconnected from its power 
supply.
 When changing the lens, avoid 
using excessive force as this may...

page 16
Installation and Quick-Start Guide
CHANGING THE FILTERS
Changing The Filters
1. Remove the two screws 1 holding the filter cover.
2. Remove the filter cover 2.
3. Remove the old filter 3.
4. Place the new filter in the slot. Make sure the air flow arrow 4 points toward the projector, as shown in the illustration.
5. Replace the filter cover and tighten the screws.
Notes
	 Before	changing	the	filters,	always make sure the projector 
is switched off and fully 
disconnected from its power 
supply....

page 17
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Operating The Projector
Switching the projector on
1. Ensure a lens is fitted. Connect the power cable between the mains supply and the projector. (See Connecting the power supply 
above.) Switch on at the switch next to the power connector.
2. The POWER indicator lights red to signal that the projector is in STANDBY mode. Press one of the following buttons:
• On the remote control, the ON button
• On the projector control panel, the...

page 18
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Selecting an input signal
1. Connect one or more image sources to the projector.
2. Select the input you want to display:
• Press one of the input buttons on the remote control.
• Alternatively, open the On-screen display (OSD) by pressing MENU. Highlight Input from the main menu, press ENTER/OK and then 
select an input signal using the UP  and DOWN  arrow buttons. Press ENTER/OK to confirm your choice.
Selecting a test pattern
To...

page 19
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Adjusting the lens
The lens can be adjusted using the Lens menu, or using the lens buttons on the remote control.
Lens menu
The Lens menu provides access to the Lens Control setting and the Lens Center command.
Lens Control allows Zoom, Focus and Shift adjustment using the arrow buttons. The setting operates in Zoom/Focus Adjustment and 
Shift Adjustment mode.
Press ENTER/SELECT to switch between the two modes.
Remote control
Use the...

Installation and Quick-Start Guide 
Digital Projection HIGHlite Laser II 3D Series  
This page is intentionally left blank.  

CONNECTION GUIDE4 
Rev A August 2016 
HIGHlite Laser II 3D Series
High Brightness Digital Video Projector  

Connection Guide
IN THIS GUIDE
IN THIS GUIDE
Signal Inputs ........................................................................\
...............................23
Digital inputs and outputs ........................................................................................23
Analog inputs and outputs .......................................................................................24
EDID on the HDMI, DisplayPort and VGA inputs ....................................................25
Using...