Digital Projection Projector HIGHlite Laser II 3D Series User Manual

page 63
Operating Guide
USING THE PROJECTOR
3D menu continued from previous page
Frame rate multiplication in 3D images
When displaying a low frame rate 3D video, the projector 
multiplies the frame rate to obtain a flicker-free image. For 
example, a 60Hz frame rate is doubled to 120 Hz, or a 48 Hz 
frame rate is tripled to 144 Hz.
Frame rate multiplication is an automatic process. It occurs in 
the background and cannot be modified by the user.
NotesL1R1L2
R2
L1
L1
R1R2
L2 L3
R2
R1
L3
L2IN
OUT
x2...

page 64
Operating Guide
USING THE PROJECTOR
Laser menu
• Power Mode
• Eco will automatically set the laser power to 80%.
• Normal will set the power to 100%.
• Set to Custom if you wish to adjust the power manually.
• Power Level
This setting is only available if Power Mode is set to Custom.
Choose a value between 20 and 100, ranging from 20% to 100% laser power.
NotesLaser
PowerLevel
Power
Mode
————
Normal  
Digital Projection HIGHlite Laser II 3D Series 
Rev A August 2016  

page 65
Operating Guide
USING THE PROJECTOR
Setup menu
• Orientation 
Choose from Front Tabletop, Front Ceiling, Rear Tabletop, Rear Ceiling and 
Auto-front.
• Cooling Condition 
Choose from Table, Ceiling, Freetilt and Auto.
• High Altitude 
Choose from On and Auto.
• Screen Setting 
Choose from 16:10, 16:9 and 4:3.
• ColorMax 
Set up user-defined color gamut values.
• Power On/Off 
Access the submenu to set up automatic projector power on and power off.
• Clock Adjust 
Access the submenu to set current...

page 66
Operating Guide
USING THE PROJECTOR
Setup menu continued from previous page
• Auto Source 
If this setting is On, the projector will automatically search for an active input source.
• Infrared Remote 
Set to Off if you wish to disable the remote control.
• IR Code 
The projector and the remote control need a matching IR code: a two-digit number 
between 00 and 99.
The default IR code is 00. This is also a master code, which, if assigned to a remote, 
will work regardless of the value assigned to...

page 67
Operating Guide
USING THE PROJECTOR
Color menu continued from previous page
ColorMax Setting
ColorMax Setting permits seven point 
color matching of red, green, blue, 
yellow, cyan, magenta and white.
You can enter your own gamut values 
here, or edit values you have imported 
using the Projector Controller 
software.
Defining your own colorspace with 
individual x and y coordinates for each 
color enables you to match not only the 
whites but each individual color as well.
Highlight the submenu...

page 68
Operating Guide
USING THE PROJECTOR
Setup menu continued from previous page
Power On/Off
• Auto Power Off
Set this to On if you want the projector to go into STANDBY mode when no input 
source is detected for 20 minutes.
• Auto Power On
Set this to On if you want the projector to start up immediately when the mains is 
connected.
Set this to Off if you want the projector to go into STANDBY mode when the mains 
is connected. In this case, the projector will not start up until the POWER button is...

page 69
Operating Guide
USING THE PROJECTOR
Setup menu continued from previous page
Clock Adjust
Use this menu to set date (in dd:MM:yyyy format), time (in HH:mm format) and time 
zone.
The date and time set here will affect any schedule created within the Power On/Off 
menu.
Notes
ClockAdjust
Time(HH:mm)
Time Zone
Date
(dd:MM:yyyy)
14:00
UTC0
20:11:2015
Notes  
Digital Projection HIGHlite Laser II 3D Series 
Rev A August 2016  

page 70
Operating Guide
USING THE PROJECTOR
Setup menu continued from previous page
OSD Settings
• Language sets the OSD language.
• Menu Position determines where the OSD should appear ont he screen when 
activated.
• Menu Transparency sets OSD transparency between 0% (no transparency), 25%, 
50% and 75%.
• Time Out determines how long the OSD should remain on screen if no buttons are 
pressed. Choose Always On to disable this feature.
• Message Box determines whether projector status messages should...

page 71
Operating Guide
USING THE PROJECTOR
Network menu
• Network Mode
Choose between Projector Control and Ser vice.
• Standby Power
If this setting is On, the LAN socket remains active when the projector is in STANDBY 
mode. If the setting is Off, the LAN socket is disabled when the projector is in 
STANDBY mode.
• DHCP, IP, Subnet Mask, Gateway, DNS
Set DHCP to On if the IP address is to be assigned by a DHCP server, or Off if it is to 
be set here.
If DHCP is On, it will not be possible to edit IP...

page 72
Operating Guide
USING THE PROJECTOR
PIP menu
• PIP
Turn PIP on and off.
• Source
Select an input source for the PIP image.
Any combinations are possible between main and PIP input source, as long as the 
two inputs are not from the same group:
Group 1Group 2
HDMI 1HDMI 2
DVIVGA
DisplayPortCOMP
HDBaseT3G-SDI
• Position
Set the location of the PIP image on the screen. Choose from Top-Left, Top-Right, 
Bottom-Left, Bottom-Right and PBP.
Notes
 Some settings may be unavailable 
depending on other...