Digital Projection Projector HIGHlite Laser II 3D Series User Manual

page 23
Connection Guide
SIGNAL INPUTS
Signal Inputs
Digital inputs and outputs
1 HDBaseT
Receives digital signal from HDBaseT-compliant devices.
2 3G-SDI in
3 3G-SDI out
Connect a 3G-SDI cable to distribute the 3G-SDI signal to another projec\
tor.
4 HDMI I
HDMI 1.4a input. Connect an HDMI cable to the connector.
5 HDMI II
HDMI 1.4a input. Connect an HDMI cable to the connector.
6 DisplayPort
DisplayPort 1.1a input. Connect a DisplayPort cable to the connector.
Supports sources up to 1920x1200...

page 24
Connection Guide
SIGNAL INPUTS
Analog inputs and outputs
1 Component
RGBHV, RGsB or RGBS
•  Set Color Space in the Color menu to Auto or  RGB-Video.
YPbPr or YCbCr
Set Color Space in the Color menu to Auto, YPbPr or YCbCr.
2 VGA
This input receives analog signals from a computer. When using this input, it is best to use a fully wired VGA cable to connect the 
source to the projector. This will allow the source to determine the projector’s capabilities via DDC and show an optimized image. 
Such...

page 25
Connection Guide
SIGNAL INPUTS
EDID on the HDMI, DisplayPort and VGA inputs
If you are using a computer graphics card or another source that obeys the EDID protocol, the source will automatically configure itself to suit 
the projector.
Otherwise refer to the documentation supplied with the source to manuall\
y set the resolution to the DMD™ resolution of the projector or the 
nearest suitable setting. Switch off the source, connect to the projector, then switch the source back on again.
Using...

page 26
Connection Guide
SIGNAL INPUTS
3D connections
3D sources up to 60Hz requiring frame doubling and left/right interleaving
1. Connect to either of the following inputs on the connection panel:
• HDMI 1
• HDMI 2
• HDBaseT
2. Set 3D Format in the 3D menu to match the format of the incoming signal. Choose from Auto, Side by Side (Half) and 
Top and Bottom.
The Frame Packing format is automatically detected by the projector.
Frame sequential 3D sources up to 120Hz
• Connect to the DisplayPort input....

page 27
Connection Guide
SIGNAL INPUTS
3D Sync
3D Sync in
Sync input signal – normally only required for Sequential 3D 
sources.
• Connect the 3D sync from your graphics card or server.
3D Sync out
Sync output signal. This may be affected by the Sync Offset 
setting in the 3D Control menu.
Connect this to your IR emitter or ZScreen.
Notes
 For a complete listing of pin 
configurations for all signal and 
control connectors, see  Appendix 
E: Wiring Details in the Reference 
Guide .
 The projector can be...

page 28
Connection Guide
CONTROL CONNECTIONS
Control Connections
1 LAN
• All of the projector’s features can be controlled via a 
LAN connection, using commands described in the 
Protocol Guide.
• Use a crossed LAN cable to connect directly to a 
computer, or an uncrossed cable to connect to a 
network hub.
This connection is also used by the HDbBaseT input.
2 Trigger 1 & Trigger 2
The Trigger outputs are activated by one of the three 
following conditions, as set in the Setup menu:
• Screen trigger: can...

page 29
Connection Guide
CONTROL CONNECTIONS
LAN connection examples
The projector’s features can be controlled via a LAN connection, using Digital Project\
ion’s Projector Controller application or a terminal-
emulation program.
Notes
 Projector Controller is available for 
download, free of charge, from the 
Digital Projection website.
Projector
Computer
Crossed 
LAN cable
Computer
Projector
Projector
Un-crossed LAN cables
Hub or LAN
1
1LAN 
Digital Projection HIGHlite Laser II 3D Series 
Rev A August...

page 30
Connection Guide
CONTROL CONNECTIONS
RS232 connection exampleNotes
1
1RS232
Projector
Computer
Straight-through 
cable 
Digital Projection HIGHlite Laser II 3D Series 
Rev A August 2016  

OPERATING GUIDE4 
Rev A August 2016 
HIGHlite Laser II 3D Series
High Brightness Digital Video Projector  

Operating Guide
IN THIS GUIDE
IN THIS GUIDE
Using The Menus ........................................................................\
.......................33
Opening the OSD ......................................................................................................33
Opening a menu ........................................................................................................33
Exiting menus and closing the OSD...