Digital Projection Projector HIGHlite Laser II 3D Series User Manual

page 3
Installation and Quick-Start Guide
WHAT’S IN THE BOX?
What’s In The Box?Notes
 Make sure your box contains 
everything listed. If any pieces are 
missing, contact your dealer.
 Only one remote will be supplied 
with the projector. For more 
information, see  Remote Control 
further in this guide.
  You should save the original box 
and packing materials, in case you 
ever need to ship your projector.
 The projector is shipped without a 
lens.
 Do not use the short lens hood 
with the  4.34 - 6.76...

page 4
Installation and Quick-Start Guide
CONNECTING THE POWER SUPPLY
Connecting The Power Supply
Lift the cable lock up, push the mains connector in firmly and 
push the lock down to secure the cable.
1 AC mains inlet with cable lock
Voltage selection
The VOLTAGE SELECT switch must be set to match the power supply you are using:
Voltage of power supply usedPosition of VOLTAGE SELECT switch
AC100V outlet
AC200V (single phase) outlet
Notes
 Use only the power cable 
provided.
 Ensure that the power outlet...

page 5
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Projector Over view
Front and rear views
1 Control panel
2 Connection panel
3 Air outlet
4 Lens hood
5 Front infrared window
6 Power switch and power connection
7 Air outlet
8 Rear infrared window
9 Air inlet
10 Adjustable feet
Notes
 Do not use the short lens hood 
with the  4.34 - 6.76 : 1 zoom lens.
 For further information about using 
the right lens and hood, see  The 
lens hood  further in this guide.
Front view
45
312
6
Rear view
78
10
9...

page 6
Installation and Quick-Start Guide
CONTROL PANEL
Control Panel
1 ON indicator (blue) Behavior   Meaning
 Off     The projector is switched off.
 On      The projector is switched ON.
 Flashing     The projector is warming up or cooling down.
2 ERROR indicator (red) Behavior    Meaning
  Flash once, then pause    Laser failure.
 Flash twice, then pause    Cover open.
 Flash three times, then pause  Fan failure.
 Flash four times, then pause  Over temperature.
 On    System error.
3 STANDBY...

page 7
Installation and Quick-Start Guide
REMOTE CONTROL
Remote Control
1 Power ON / OFF
Turns power on and off.
2 Pic Mute ON / OFF
Shows and hides the projected image.
When OFF, the light source is completely switched off and the screen is black.
2 OSD ON / OFF
Enable and disable screen timeout messages and control whether to show t\
he OSD 
during projection.
4 MENU
Access the OSD. If the OSD is open, press this button to go back to the \
previous menu.
5 Navigation (arrows and OK)
Navigate through...

page 8
Installation and Quick-Start Guide
REMOTE CONTROL
11 LENS adjustment
FOCUS IN / OUT: adjust focus.
SHIFT: press and hold this button, then use the Navigation arrow 
buttons to move the lens.
ZOOM IN / OUT: adjust zoom.
12 USER PRESET A, B, C, D
Load user presets.
13 A LT
Press and hold this button to access alternative functions for all 
buttons with a green label.
14 DVI / GAMMA / numeric input 3
Select the DVI input.
Use with A LT to switch to the next Gamma value:
...1.0, 1.8, 2.0, 2.2, 2.35,...

page 9
Installation and Quick-Start Guide
REMOTE CONTROL
17 DISPLAYPORT / R / numeric input 4
Select DisplayPort input.
18 HD-T / G / numeric input 5
Select the HDBaseT input.
19 3GSDI / B / numeric input 6
Select the 3G-SDI input.
20 VGA / 3D / numeric input 7
Select the VGA input.
Use with A LT to toggle the 3D Format setting between Off and Auto.
21 COMP1 / EYE / numeric input 8
Select the Component 1 input. 
Use with A LT to switch between left and right eye 3D dominance.
22 COMP2 / PIP / numeric...

page 10
Installation and Quick-Start Guide
REMOTE CONTROL
Infrared reception
The projector has infrared sensors at the front and back.
The angle of acceptance is 40°. Make sure that the remote control is \
within the angle of 
acceptance when trying to control the projector.
40°
40°
Infrared reception
Notes 
Digital Projection HIGHlite Laser II 3D Series 
Rev A August 2016  

page 11
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Positioning The Screen And Projector
1. Install the screen, ensuring that it is in the best position for viewing\
 by your audience.
2. Mount the projector, ensuring that it is at a suitable distance from the screen for the image to fill the screen. Set the adjustable feet so that 
the projector is level, and perpendicular to the screen.
The drawing below shows the positions of the feet for table mounting, and the fixing...

page 12
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Roll and pitch
The projector can be operated in numerous positions.
It is not recommended to position the projector in portrait mode with in\
puts facing upward, as shown in the diagram.
1 Positions to avoid: inputs side up
2 Recommended positions
Notes
360°2
Pitch
30°
330°
2
1
Roll 
Digital Projection HIGHlite Laser II 3D Series 
Rev A August 2016