Digital Projection Projector HIGHlite Laser II 3D Series User Manual

							page 3
Installation and Quick-Start Guide
WHAT’S IN THE BOX?
What’s In The Box?Notes
 Make sure your box contains 
everything listed. If any pieces are 
missing, contact your dealer.
 Only one remote will be supplied 
with the projector. For more 
information, see  Remote Control 
further in this guide.
  You should save the original box 
and packing materials, in case you 
ever need to ship your projector.
 The projector is shipped without a 
lens.
 Do not use the short lens hood 
with the  4.34 - 6.76 : 1 zoom lens.
 For further information about using 
the right lens and hood, see  The 
lens hood  further in this guide.
 Only one power cable - dependent 
on the destination territory - will be 
supplied with the projector.
Remote control 
(116-088)
2x AAA batteries
User Manual on disc 
(115-759)
Important Information (114-914)
Power cable, Europe 
(112-001)
Power cable, North America 
(112-002)
Projector
Power cable, United Kingdom 
(112-000)
HDMI cable
Pic Mute
OFF ONMENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOMIN
OUT IN
OUT
SHIFT
2
1 3HDMI2DVIDISPLAYPORT
HD-T3GSDI
VGA COMP1 COMP2
BRI
TEST
CON
GAMMA
R G BALL
3D EYE PIPSWAP456
7 89 0
ALT
ADDR
OSD
OFF ON
DEFAULTFREEZE
RE
-SYNCA BC DUSER PRESET
Power cable, China 
Digital Projection HIGHlite Laser II 3D Series 
Rev A August 2016  
						

							page 4
Installation and Quick-Start Guide
CONNECTING THE POWER SUPPLY
Connecting The Power Supply
Lift the cable lock up, push the mains connector in firmly and 
push the lock down to secure the cable.
1 AC mains inlet with cable lock
Voltage selection
The VOLTAGE SELECT switch must be set to match the power supply you are using:
Voltage of power supply usedPosition of VOLTAGE SELECT switch
AC100V outlet
AC200V (single phase) outlet
Notes
 Use only the power cable 
provided.
 Ensure that the power outlet 
includes a ground connection as 
this equipment MUST be earthed.
 Handle the power cable carefully 
and avoid sharp bends. Do not 
use a damaged power cable.
1 
Digital Projection HIGHlite Laser II 3D Series 
Rev A August 2016  
						

							page 5
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Projector Over view
Front and rear views
1 Control panel
2 Connection panel
3 Air outlet
4 Lens hood
5 Front infrared window
6 Power switch and power connection
7 Air outlet
8 Rear infrared window
9 Air inlet
10 Adjustable feet
Notes
 Do not use the short lens hood 
with the  4.34 - 6.76 : 1 zoom lens.
 For further information about using 
the right lens and hood, see  The 
lens hood  further in this guide.
Front view
45
312
6
Rear view
78
10
9 
Digital Projection HIGHlite Laser II 3D Series 
Rev A August 2016  
						

							page 6
Installation and Quick-Start Guide
CONTROL PANEL
Control Panel
1 ON indicator (blue) Behavior   Meaning
 Off     The projector is switched off.
 On      The projector is switched ON.
 Flashing     The projector is warming up or cooling down.
2 ERROR indicator (red) Behavior    Meaning
  Flash once, then pause    Laser failure.
 Flash twice, then pause    Cover open.
 Flash three times, then pause  Fan failure.
 Flash four times, then pause  Over temperature.
 On    System error.
3 STANDBY indicator (green) Behavior   Meaning
 On     The projector is in STANDBY mode.
 Flashing     The projector is in STANDBY mode. 
        It can be switched on with a network command.
4 MENU button
Access the projector OSD (on-screen display).
5 Navigation (arrow buttons and ENTER)
Navigate the OSD and edit settings with the arrows, confirm choice with ENTER.
6 INPUT button
Select input source.
7 Focus IN / OUT
Adjust focus.
8 Zoom IN / OUT
Adjust zoom.
9 Shutter CLOSE / OPEN
Open and close the shutter.
10 POWER button
Switch the projector on and off (in STANDBY mode)
11 EXIT button
Close the OSD.
12 SHIFT button
Press and hold this button, then press the arrow buttons to move the len\
s.
ERROR STANDBY
INPUT CLOSE FOCUS
ZOOM
SHUTTER OPEN
OUT
IN
OUT IN
SHIFT
MENU
EXIT
4
5
6
3
8
1
2
9
7
10
12
11
Notes 
Digital Projection HIGHlite Laser II 3D Series 
Rev A August 2016  
						

							page 7
Installation and Quick-Start Guide
REMOTE CONTROL
Remote Control
1 Power ON / OFF
Turns power on and off.
2 Pic Mute ON / OFF
Shows and hides the projected image.
When OFF, the light source is completely switched off and the screen is black.
2 OSD ON / OFF
Enable and disable screen timeout messages and control whether to show t\
he OSD 
during projection.
4 MENU
Access the OSD. If the OSD is open, press this button to go back to the \
previous menu.
5 Navigation (arrows and OK)
Navigate through the menus with the arrows, confirm your choice with OK.
In lens adjustment modes, the arrows are used to move, zoom or focus the\
 lens. See 11 
below.
In lens adjustment modes, or when the OSD is not showing, the OK button switches 
between modes: Shift Adjustment and Zoom / Focus Adjustment.
6 EXIT
Go up one level in the OSD. When the top level is reached, press to clos\
e the OSD.
7 FREEZE
Freeze the current frame.
8 DEFAULT
When editing a parameter, press this button to restore the default value.
9 INFO
Access information about the projector.
10 RE-SYNC
Re-synchronise with the current input signal.
continues on next page...
PicMute
OFF ON
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENSFOCUS ZOOM
IN
OUT IN
OUT
SHIFT
2
1 3
HDMI2DVI
DISPLAYPORTHD-T3GSDI
VGA COMP1 COMP2
BRI
TEST
CON
GAMMA
R G BALL
3D EYE PIPSWAP
456
7 89 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZERE
-SYNC
A BC D
USER PRESET
1
2
5
6
84
9
7
3
10
Notes 
Digital Projection HIGHlite Laser II 3D Series 
Rev A August 2016  
						

							page 8
Installation and Quick-Start Guide
REMOTE CONTROL
11 LENS adjustment
FOCUS IN / OUT: adjust focus.
SHIFT: press and hold this button, then use the Navigation arrow 
buttons to move the lens.
ZOOM IN / OUT: adjust zoom.
12 USER PRESET A, B, C, D
Load user presets.
13 A LT
Press and hold this button to access alternative functions for all 
buttons with a green label.
14 DVI / GAMMA / numeric input 3
Select the DVI input.
Use with A LT to switch to the next Gamma value:
...1.0, 1.8, 2.0, 2.2, 2.35, 2.5...
15 HDMI 2 / CON / numeric input 2
Select the HDMI 2 input.
Use with A LT to bring up the Contrast control, then adjust the value 
with the LEFT and RIGHT arrow buttons.
16 HDMI 1 / BRI / numeric input 1
Select the HDMI 1 input.
Use with A LT to bring up the Brightness control, then adjust the 
value with the LEFT and RIGHT arrow buttons.
17 TEST / SWAP / numeric input 0
Show a test pattern. Press again to show the next test pattern:
...Off, White, Black, Red, Green, Blue, CheckerBoard, 
CrossHatch, V Burst, H Burst, ColorBar...
When PIP mode is on, use this button with A LT to swap the main and 
sub images.
continues on next page...
Notes
 For further information about 
user presets, see Memory in the 
Operating Guide .
Remote control
PicMute
OFF ON
MENU
EXIT INFO
HDMI1
OK
OFFON
ALT
LENSFOCUS ZOOM
IN
OUT IN
OUT
SHIFT
2
1 3
HDMI2DVI
DISPLAYPORTHD-T3GSDI
VGA COMP1 COMP2
BRI
TEST
CON
GAMMA
R G BALL
3D EYE PIPSWAP
456
7 89 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZERE
-SYNC
A BC D
USER PRESET
13
11
12
14
15
16
17 
Digital Projection HIGHlite Laser II 3D Series 
Rev A August 2016  
						

							page 9
Installation and Quick-Start Guide
REMOTE CONTROL
17 DISPLAYPORT / R / numeric input 4
Select DisplayPort input.
18 HD-T / G / numeric input 5
Select the HDBaseT input.
19 3GSDI / B / numeric input 6
Select the 3G-SDI input.
20 VGA / 3D / numeric input 7
Select the VGA input.
Use with A LT to toggle the 3D Format setting between Off and Auto.
21 COMP1 / EYE / numeric input 8
Select the Component 1 input. 
Use with A LT to switch between left and right eye 3D dominance.
22 COMP2 / PIP / numeric input 9
Select the Component 2 input.
Use with A LT to switch on Picture In Picture (PIP) mode.
23 ADDR / ALL (with red indicator at the top)
Assign and unassign an IR remote address.
To assign an address:
1. Press and hold this button until the indicator starts flashing.
2. Release this button and while the indicator is still flashing, enter 
a two-digit address using the numeric input buttons. The indicator 
will flash three times quickly to confirm the change.
To unassign an address and return to the default address 00,
• Press and hold A LT and this button simultaneously until the 
indicator flashes to confirm the change.
Notes
Remote control bottom
PicMute
OFF ON
MENU
EXIT INFO
HDMI1
OK
OFFON
ALT
LENSFOCUS ZOOM
IN
OUT IN
OUT
SHIFT
2
1 3
HDMI2DVI
DISPLAYPORTHD-T3GSDI
VGA COMP1 COMP2
BRI
TEST
CON
GAMMA
R G BALL
3D EYE PIPSWAP
456
7 89 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZERE
-SYNC
A BC D
USER PRESET
23
18
19
17
20
21
22
PicMute
OFF ON
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENSFOCUS ZOOM
IN
OUT IN
OUT
SHIFT
2
1 3
HDMI2DVI
DISPLAYPORTHD-T3GSDI
VGA COMP1 COMP2
BRI
TEST
CON
GAMMA
R G BALL
3D EYE PIPSWAP
456
7 89 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZERE
-SYNC
A BC D
USER PRESET
Remote control top 
Digital Projection HIGHlite Laser II 3D Series 
Rev A August 2016  
						

							page 10
Installation and Quick-Start Guide
REMOTE CONTROL
Infrared reception
The projector has infrared sensors at the front and back.
The angle of acceptance is 40°. Make sure that the remote control is \
within the angle of 
acceptance when trying to control the projector.
40°
40°
Infrared reception
Notes 
Digital Projection HIGHlite Laser II 3D Series 
Rev A August 2016  
						

							page 11
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Positioning The Screen And Projector
1. Install the screen, ensuring that it is in the best position for viewing\
 by your audience.
2. Mount the projector, ensuring that it is at a suitable distance from the screen for the image to fill the screen. Set the adjustable feet so that 
the projector is level, and perpendicular to the screen.
The drawing below shows the positions of the feet for table mounting, and the fixing holes for ceiling mounting.
1 Four adjustable feet
2 Six M6 holes for ceiling mount
The screws should not penetrate more than 15 mm into 
the body of the projector.
Notes
 Always allow the projector 
to cool for 5 minutes before 
disconnecting the power or 
moving the projector.
 Ensure that there is at least 50 
cm (20 in) of space between the 
ventilation outlets and any wall, 
and 30 cm (12 in) on all other 
sides.
 Do not stack more than 3 
projectors.1
2
1
1
1
2
2
2
2
2 
Digital Projection HIGHlite Laser II 3D Series 
Rev A August 2016  
						

							page 12
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Roll and pitch
The projector can be operated in numerous positions.
It is not recommended to position the projector in portrait mode with in\
puts facing upward, as shown in the diagram.
1 Positions to avoid: inputs side up
2 Recommended positions
Notes
360°2
Pitch
30°
330°
2
1
Roll 
Digital Projection HIGHlite Laser II 3D Series 
Rev A August 2016