Digital Projection Projector HIGHlite Laser II 3D Series User Manual

							page 13
Installation and Quick-Start Guide
CHANGING THE LENS
Changing The Lens
The lens hood
There are two types of lens hood, short and long. 
The short lens hood is used with the following lenses:
Throw ratiosPart number
0.77 : 1 fixed lens110-808
1.16 : 1 fixed lens110-809
1.45 - 1.74 : 1 zoom lens110-803
1.74 - 2.17 : 1 zoom lens112-878
2.17 - 2.90 : 1 zoom lens113-852
2.90 - 4.34 : 1 zoom lens110-806
The long lens hood must be used with the following long throw lens:
Throw ratiosPart number
4.34 - 6.76 : 1 zoom lens110-807
Projector with short lens hood fittedProjector with long lens hood fitted
Notes
  Before changing the lens, 
always make sure the projector 
is switched off and fully 
disconnected from its power 
supply.
 When changing the lens, avoid 
using excessive force as this may 
damage the equipment.
  Take care to preserve the original 
lens packaging and protective caps 
for future use.
 Do not use the short lens hood 
with the  4.34 - 6.76 : 1 zoom lens.
 The projector will not power on 
without the lens and lens hood fitted. 
Digital Projection HIGHlite Laser II 3D Series 
Rev A August 2016  
						

							page 14
Installation and Quick-Start Guide
CHANGING THE LENS
Inserting a new lens
1. Insert the lens into the lens aperture, making sure that the plug on the\
 zoom drive 
mechanism lines up with socket on the right of the lens aperture.
2. Rotate the lens clockwise until it clicks into place.
3. Secure the lens hood to the front of the projector with the screws.
Notes
 Before changing the lens, 
always make sure the projector 
is switched off and fully 
disconnected from its power 
supply.
 When changing the lens, avoid 
using excessive force as this may 
damage the equipment.
  Take care to preserve the original 
lens packaging and protective caps 
for future use.
 Do not use the short lens hood 
with the  4.34 - 6.76 : 1 zoom lens.
 The projector will not power on 
without the lens and lens hood fitted. 
Digital Projection HIGHlite Laser II 3D Series 
Rev A August 2016  
						

							page 15
Installation and Quick-Start Guide
CHANGING THE LENS
Removing the lens
1. Loosen the four screws securing the lens hood to the body of the project\
or. 
Remove the lens hood.
2. Push down the lens holder tab.
3. Rotate the lens anti-clockwise.
4. Pull the lens forward to remove it from the lens aperture.
Notes
 Before changing the lens, 
always make sure the projector 
is switched off and fully 
disconnected from its power 
supply.
 When changing the lens, avoid 
using excessive force as this may 
damage the equipment.
  Take care to preserve the original 
lens packaging and protective caps 
for future use.
 The projector will not power on 
without the lens and lens hood fitted. 
Digital Projection HIGHlite Laser II 3D Series 
Rev A August 2016  
						

							page 16
Installation and Quick-Start Guide
CHANGING THE FILTERS
Changing The Filters
1. Remove the two screws 1 holding the filter cover.
2. Remove the filter cover 2.
3. Remove the old filter 3.
4. Place the new filter in the slot. Make sure the air flow arrow 4 points toward the projector, as shown in the illustration.
5. Replace the filter cover and tighten the screws.
Notes
	 Before	changing	the	filters,	always make sure the projector 
is switched off and fully 
disconnected from its power 
supply.
	When	changing	the	filters,	avoid	using excessive force as this may 
damage the equipment.
  In a normal environment the filters 
should be changed every 2000 
hours.
4312 
Digital Projection HIGHlite Laser II 3D Series 
Rev A August 2016  
						

							page 17
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Operating The Projector
Switching the projector on
1. Ensure a lens is fitted. Connect the power cable between the mains supply and the projector. (See Connecting the power supply 
above.) Switch on at the switch next to the power connector.
2. The POWER indicator lights red to signal that the projector is in STANDBY mode. Press one of the following buttons:
• On the remote control, the ON button
• On the projector control panel, the POWER button.
The fans begin working, then the POWER indicator begins flashing green. When the flashing stops, the POWER and LIGHT indicators 
both light steady green. The projector is switched on.
Switching the projector off
1. Press OFF on the remote control or POWER on the control panel, then press again to confirm your choice.
The POWER indicator on the control panel will start flashing amber, the system will go out and the cooling fans will run for a short time 
until the POWER indicator goes stready red to indicate that the projector has entered S\
TANDBY mode.
2. If you need to switch the projector off completely, switch off at the mains power switch next to the power connector and then disconn\
ect 
the power cable from the projector.
Notes
 See also Connecting The Power 
Supply  earlier in this guide.
 The self-test is running when all the 
LEDs on the control panel are lit.
 Use only the power cable 
provided.
 Ensure that the power outlet 
includes a ground connection as 
this equipment MUST be earthed.
 Handle the power cable carefully 
and avoid sharp bends. Do not 
use a damaged power cable. 
Digital Projection HIGHlite Laser II 3D Series 
Rev A August 2016  
						

							page 18
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Selecting an input signal
1. Connect one or more image sources to the projector.
2. Select the input you want to display:
• Press one of the input buttons on the remote control.
• Alternatively, open the On-screen display (OSD) by pressing MENU. Highlight Input from the main menu, press ENTER/OK and then 
select an input signal using the UP  and DOWN  arrow buttons. Press ENTER/OK to confirm your choice.
Selecting a test pattern
To display a test pattern:
• Press TEST on the remote control.
Change the test pattern using the LEFT  and RIGHT  arrow buttons.Test patterns are displayed in the following order:
White, Black, Red, Green, Blue, CheckerBoard, CrossHatch, V Burst, H Bur\
st, ColorBar, Screen Layout, Off
• Alternatively, open the OSD by pressing MENU. Highlight Test Patterns from the main menu, then select a test pattern using the LEFT 
and RIGHT arrow buttons.
After the final test pattern, the projector exits test pattern mode and returns to the main image. To view test patterns again, you need to press 
TEST again. If you wish to exit the test patterns before you reach the final one,
• press TEST or EXIT at any time.
Notes
 For full details of how to use the 
controls and the menu system, see 
the Operating Guide . 
Digital Projection HIGHlite Laser II 3D Series 
Rev A August 2016  
						

							page 19
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Adjusting the lens
The lens can be adjusted using the Lens menu, or using the lens buttons on the remote control.
Lens menu
The Lens menu provides access to the Lens Control setting and the Lens Center command.
Lens Control allows Zoom, Focus and Shift adjustment using the arrow buttons. The setting operates in Zoom/Focus Adjustment and 
Shift Adjustment mode.
Press ENTER/SELECT to switch between the two modes.
Remote control
Use the remote control to adjust zoom, focus and shift directly, without opening a menu:
• OK enters lens control, then switches between Zoom/Focus Adjustment and Shift Adjustment.
• EXIT exits lens control and opens the Lens menu.
• MENU exits lens control and returns to the main image.
• The arrow buttons adjust zoom, focus and shift as indicated on the scree\
n.
Adjusting the image
Orientation• This can be set from the Setup menu.
Highlight Orientation and choose from Front Tabletop, Front Ceiling, Rear Tabletop, Rear Ceiling and Auto-front.
Keystone• This can be set from the Geometr y menu.
Picture
• Settings such as Gamma, Brightness, Contrast, Saturation, Hue and Sharpness can be set from the Image menu.
Notes
 When adjusting focus and zoom, 
you may find it useful to display 
the CrossHatch  test pattern: press 
TEST on the remote control and 
navigate through the list of patterns 
using the 
LEFT  and RIGHT  
arrow buttons.
  For full details of how to adjust 
the lens using the remote control, 
see Remote Control earlier in this 
guide.
Setup menu
Geometr y menu
Image menu 
Digital Projection HIGHlite Laser II 3D Series 
Rev A August 2016  
						

							Installation and Quick-Start Guide 
Digital Projection HIGHlite Laser II 3D Series  
This page is intentionally left blank.  
						

							CONNECTION GUIDE4 
Rev A August 2016 
HIGHlite Laser II 3D Series
High Brightness Digital Video Projector  
						

							Connection Guide
IN THIS GUIDE
IN THIS GUIDE
Signal Inputs ........................................................................\
...............................23
Digital inputs and outputs ........................................................................................23
Analog inputs and outputs .......................................................................................24
EDID on the HDMI, DisplayPort and VGA inputs ....................................................25
Using HDMI/DisplayPort switchers with the projector ..........................................25
3D connections .........................................................................................................26
3D sources up to 60Hz requiring frame doubling and left/right interleaving ...................26
Frame sequential 3D sources up to 120Hz .....................................................................26
Dual Pipe 3D .....................................................................................................\
..............26
3D Sync ......................................................................................................................27
3D Sync in .....................................................................................................\
..................27
3D Sync out  ....................................................................................................\
................27
Control Connections ........................................................................\
................28
LAN connection examples .......................................................................................29
RS232 connection example ......................................................................................30 
Digital Projection HIGHlite Laser II 3D Series 
Rev A August 2016