Digital Projection Projector HIGHlite Cine 330 3D Series User Manual

							page 43
Operating Guide
MENU MAP
Menu Map
Menu Sub-menus and settings
MAIN
Aspect Ratio 16:9, Theaterscope, 4:3, 4:3 Narrow, 16:10, 5:4, Native
Presets
Recall A, B, C, D, Default
Save A,, B, C, D
Overscan Of f, Crop, Zoom
3D Control
3D Format Of f, Auto, Side by Side (Half), Top and Bottom, Dual-Pipe, Frame Sequential
3D Swap Normal, Reverse
Dark Time 0.65 ms, 1.3 ms, 1.95 ms, 2.5 ms
Sync Delay value between -3.0 ms and 3.0 ms (0.0 ms)
Input Select HDMI 1, HDMI 2, RGB, COMP 1, COMP 2
Resync executable command
IMAGE
Brightness value between 0 and 200 (10 0)
Contrast value between 0 and 200 (10 0)
Saturation value between 0 and 200 (10 0)
Hue value between 0 and 200 (10 0)
Sharpness value between 0 and 200 (0)
Noise Reduction value between 0 and 200 (0)
Notes
 Some of the information in this menu 
map is summarised. See the actual 
menu on the projector for full detail.
 The underlined text  represents 
the factory default value for each 
setting.
  The default value of a slider is given 
in brackets next to the setting.
   
    
Digital Projection HIGHlite Cine 330 3D Series 
Rev E August 2014  
						

							page 44
Operating Guide
MENU MAP
Menu Sub-menus and settings
ADVANCED IMAGE
Colorspace Auto, YPbPr, YCbCr, RGB PC, RGB Video
Gamma CRT (2.5), Film (2.2), Video, Punch (2.0), Graphics
Color Temperature 5500, 6500, 7500, 9300, Native
Color Gamut Auto, REC709, SMPTE-C, EBU, Native
Dynamic Black Of f, On
Adaptive Contrast Of f, On
RGB Adjust
Red Offset value between 0 and 200 (10 0)
Green Offset value between 0 and 200 (10 0)
Blue Offset value between 0 and 200 (10 0)
Red Gain value between 0 and 200 (10 0)
Green Gain value between 0 and 200 (10 0)
Blue Gain value between 0 and 200 (10 0)
Fine Sync
V Position value between 0 and 200 (10 0)
H Position value between 0 and 200 (10 0)
Phase value between 0 and 200 (10 0)
Tracking value between 0 and 200 (10 0)
Sync Level value between 0 and 200 (10 0)
Notes
 Some of the information in this menu 
map is summarised. See the actual 
menu on the projector for full detail.
 The underlined text  represents 
the factory default value for each 
setting.
  The default value of a slider is given 
in brackets next to the setting.
   
    
Digital Projection HIGHlite Cine 330 3D Series 
Rev E August 2014  
						

							page 45
Operating Guide
MENU MAP
Menu Sub-menus and settings 
SYSTEM
OSD Settings
Menu Position Left-Upper, Right-Upper, Left-Bottom, Right-Bottom, Center
Menu Transparency 0%, 25%, 50%, 75%
Time Out Always On, 10 sec, 30 sec, 60 sec
Message Box Off, On
Blank Screen Splash, Black, Blue, White
Auto Power Off Off, On)
Auto Power On Off, On)
Projection Mode Front Tabletop, Front Ceiling, Rear Tabletop, Rear Ceiling
Startup Splash Off, On
Altitude High, Auto
Lamp Power Economy, Standard
CONTROL
Trigger 1 Screen, 16:9, Theaterscope, 4:3, 4:3 Narrow, RS232
Trigger 2 Screen, 16:9, Theaterscope, 4:3, 4:3 Narrow, RS232
Auto-Source Off, On
Infrared Remote Off, On
Standby Network Off, On
Lens Control
Focus adjust
Zoom adjust
Lens Shift adjust horizontal and vertical
SERVICE
Information
Model Name, Serial Number, Software Version, FPGA Version
Active Source, Signal Format, PCLK
Lamp Hours
Factory Reset (Projector will ask for confirmation before restoring factory default settings.)
Test Patterns Off, White, Black, Red, Green, Blue, Cyan, Magenta, Yellow, Chequer Board, Alignment Grid, Vertical 
Burst, Horizontal Burst, Color Bars
Notes
 Some of the information in this menu 
map is summarised. See the actual 
menu on the projector for full detail.
 The underlined text  represents 
the factory default value for each 
setting.
   
    
Digital Projection HIGHlite Cine 330 3D Series 
Rev E August 2014  
						

							Operating Guide
   
    
Digital Projection HIGHlite Cine 330 3D Series 
This page is intentionally left blank.  
						

							REMOTE COMMUNICATIONS GUIDE4 
Rev E August 2014 
HIGHlite Cine 330 3D Series
 High Brightness Digital Video Projector  
						

							Remote Communications Guide
IN THIS GUIDE
IN THIS GUIDE
Introduction ........................................................................\
...........................49
Examples......................................................................................................49
The Operation Commands ...................................................................50
Main menu....................................................................................................50
Image menu .................................................................................................51
Advanced Image menu ...............................................................................51
System menu ...............................................................................................52
Control menu ...............................................................................................53
Service menu ...............................................................................................54
Miscellaneous commands ..........................................................................55
IP Configuration Utility ........................................................................\
...56
   
    
Digital Projection HIGHlite Cine 330 3D Series 
Rev E August 2014  
						

							page 49
Remote Communications Guide
INTRODUCTION
Introduction
The projector can be controlled by using an external control system or a\
 PC via an RS232 or LAN interface, using a terminal-emulation 
program, such as HyperTerminal.
Operation commands are used to simulate menu operations and determine th\
e settings of the projector, and use the following format:
• All commands consist of ASCII text strings starting with the letters ‘op’, and ending with\
 an ASCII Carriage Return character: 
op   [CR]
• The  string determines which setting the command will affect. For example, “aspect” stands for aspect ratio.
• The  string can take one of the following formats:
CommandDescription
Set= Makes the setting take that value.
Get?Asks what the current value is.
The value is returned as an ASCII text string.
Increment+Adds 1 to the current value.
Decrement–Subtracts 1 from the current value.
Execute(none)Performs an action.
Examples
op aspect = 1 [CR] sets the aspect ratio to TheaterScope.
op aspect ? [CR]   asks what is the current aspect ratio.
op bright + [CR]    increments the brightness setting.
op contrast – [CR] decrements the contrast setting.
op resync [CR]   commands the projector to attempt to re-synchronise to the current input\
 source.
Notes
 The Serial Port settings are:
•  Baud rate - 9,600 bps
•  Data length - 8 bits
•  Stop bits - one
•  Parity - none
•  Flow control - none
 The default IP is 192.168.0.100 and 
the TCP port number is 7000.  
The IP address can be changed - 
see IP Configuration Utility  later in 
this guide.
  Spaces in commands are 
necessary, therefore:
• 
op aspect = 1 is correct;
• 
opaspect=1 is incorrect.
   
    
Digital Projection HIGHlite Cine 330 3D Series 
Rev E August 2014  
						

							page 50
Remote Communications Guide
THE OPERATION COMMANDS
The Operation Commands

Main menu
aspect= ?0 = 16:9 
1 = TheaterScope 
2 = 4:3 
3 = 4:3 Narrow 
4 = 16:10 
5 = 5:4 
6 = Native
recall.mem= ?0 = Preset A 
1 = Preset B 
2 = Preset C 
3 = Preset D 
4 = Default
save.mem=0 = Preset A 
1 = Preset B 
2 = Preset C 
3 = Preset D
overscan= ?0 = Off 
1 = Crop 
2 = Zoom
s3d.inputtype= ?0 = Off 
1  = Auto 
2 = Side by Side (Half) 
3 = Top and Bottom 
4 = Dual-Pipe 
5 = Frame Sequential
s3d.chswap= ?0 = Normal 
1 = Swap
s3d.darktime= ?0 = 0.65 ms 
1 = 1.3 ms 
2 = 1.95 ms 
3 = 2.5 ms
continued on next page...
Notes
 If the projector is in Side by Side 
(Half)
 3D mode and you intend to 
switch to 
Frame Sequential, you 
MUST first switch back to 2D and 
then switch to the other 3D mode.
   
    
Digital Projection HIGHlite Cine 330 3D Series 
Rev E August 2014  
						

							page 51
Remote Communications Guide
THE OPERATION COMMANDS

s3d.syncdelay= ?0 - 60
input= ?0 = HDMI 1 
1 = HDMI 2 
2 = RGB 
3 = Component 1 
4 = Component 2
resync(none)(none)
Image menu
brightness= ? + -0 - 200
contrast= ? + -0 - 200
saturation= ? + -0 - 200
hue= ? + -0 - 200
sharpness= ? + -0 - 200
nr= ? + -0 - 200
Advanced Image menu
color.space= ?0  = Auto 
1 = YPbPr 
2 = YCbCr 
3 = RGB-PC 
4 = RGB-Video
gamma= ?0 = CRT 
1 = Film 
2 = Video 
3 = Punch 
4 = Graphics
color.temp= ?0 = 5500K 
1 = 6500K 
2 = 7500K 
3 = 9300K 
4 = Native
continued on next page...
Notes
 The numeric value assigned to 
s3d.syncdelay  corresponds to 
a delay in milliseconds between -3 
and 3 ms. For example, 0 = -3 ms, 
30 = 0 ms and 60 = 3ms. 
To work out the sync delay time, use 
the following formula:  
SyncDelay =  x 0.1 - 3.
   
    
Digital Projection HIGHlite Cine 330 3D Series 
Rev E August 2014  
						

							page 52
Remote Communications Guide
THE OPERATION COMMANDS

color.gamut= ?0  = Auto 
1 = REC709 
2 = SMPTE C 
3 = EBU 
4 = Native
db= ?0 = Off 
1 = On
adcontrast= ?0 = Off 
1 = On
red.offset= ? + -0 - 200
green.offset= ? + -0 - 200
blue.offset= ? + -0 - 200
red.gain= ? + -0 - 200
green.gain= ? + -0 - 200
blue.gain= ? + -0 - 200
vert.pos= ? + -0 - 200
hori.pos= ? + -0 - 200
phase= ? + -0 - 200
tracking= ? + -0 - 200
sync.level= ? + -0 - 200
System menu
osd.menupos= ?0 = Left Upper 
1 = Right Upper
2 = Left Bottom
3 = Right Bottom
4 = Center
osd.trans= ?0 = 0%
1 = 25%
2 = 50%
3 = 75%
continued on next page...
Notes
 db controls Dynamic Black
 adcontrast controls Adaptive 
Contrast
   
    
Digital Projection HIGHlite Cine 330 3D Series 
Rev E August 2014