Digital Projection Projector HIGHlite Cine 330 3D Series User Manual

							OPERATING GUIDE4 
Rev E August 2014 
HIGHlite Cine 330 3D Series
 High Brightness Digital Video Projector  
						

							Operating Guide
IN THIS GUIDE
IN THIS GUIDE
Using The Menus ........................................................................\
................25
Opening the OSD .........................................................................................25
Opening a menu ..........................................................................................25
Exiting menus and closing the OSD 
..........................................................25
Inside a menu ..............................................................................................26
Accessing sub-menus .........................................................................26
Executing commands  ..........................................................................26
Editing projector settings  ...........................................................................27
Choosing a value from a list ................................................................27
Changing the value without viewing the list ........................................27
Using a slider to set a value ................................................................27
A Tour Of  The Menus ........................................................................\
.......28
Main menu....................................................................................................28
Aspect Ratio  ........................................................................................29
Presets ................................................................................................30
Overscan  .............................................................................................31
3D Control  ...........................................................................................32
Input Select .........................................................................................33
Resync ................................................................................................33
Image menu .................................................................................................34
Advanced Image menu ...............................................................................35
Colorspace ..........................................................................................35
Gamma ...............................................................................................36
Color Temperature ..............................................................................36
Color Gamut ........................................................................................37
Dynamic Black  ....................................................................................37
Adaptive Contrast................................................................................38
RGB Adjust..........................................................................................38
Fine Sync ............................................................................................39
System menu ...............................................................................................40
OSD Settings ......................................................................................41
Control menu ...............................................................................................42
Service menu ...............................................................................................42
Factory Reset ......................................................................................42
Test Pattern .........................................................................................42
Menu Map ........................................................................\
................................43
MAIN .............................................................................................................43
IMAGE...........................................................................................................43
ADVANCED IMAGE  .....................................................................................44
SYSTEM........................................................................................................45
CONTROL .....................................................................................................45
SERVICE .......................................................................................................45
   
    
Digital Projection HIGHlite Cine 330 3D Series 
Rev E August 2014  
						

							page 25
Operating Guide
USING THE MENUS
Using The Menus
Opening the OSD
Access the various menus using either the projector control panel or the\
 
remote control. On either device,
• press the MENU button.
The on-screen display (OSD) opens showing the list of available menus.\
Opening a menu
Move up and down the list using the UP and DOWN  arrow buttons. 
To open a menu,
• press ENTER (on the remote control) or SELECT (on the control panel).
This guide refers to the above two buttons as ENTER/SELECT.
Exiting menus and closing the OSD
To go back to the previous page,
• press MENU.
When you reach the top level, pressing MENU will close the OSD.
Notes
MENUMENUPOWERPOWER
SELECT
SELECT
SOURCESOURCE
LEDSTATUSLEDSTATUSISSUEISSUEPOWERPOWERSTAND BYSTANDBY
2
PIC
MUTE4
B
SHARP
O -SCANNRGAMMA
C-TEMPTESTBRI -C
3D
SWAP3 D
FORMAT2 D /3 D
ENTER
SOURCE
3
6
1
ASPECT
RATIO
MENU
USER
MEMORY
CA
|
ON POWER OFF
IMAGE
MAIN
ADVANCED IMAGE SYSTEM
CONTROL
SERVICE
Projector control panel
Remote control
On-screen display: top level (list of available menus)
   
    
Digital Projection HIGHlite Cine 330 3D Series 
Rev E August 2014  
						

							page 26
Operating Guide
USING THE MENUS
Inside a menu
When you open a menu, the page consists of the following elements:
• Title bar at the top 
Shows which menu (and sub-menu) you have accessed.
• Highlighted item
• Available and unavailable items 
Unavailable items appear grayed out. Whether an item is available may 
depend on other settings.
• Text next to each item 
Shows whether the item:
• has a value that can be changed (shows the current value)
• opens a sub-menu (says )
• executes a command (says )
Accessing sub-menus
Use the UP  and DOWN  arrow buttons to highlight the sub-menu, then 
press ENTER/SELECT.
Executing commands
If the item contains a command, press ENTER/SELECT to execute it.
You may be asked for confirmation. Use the LEFT  and RIGHT  arrow 
buttons to select your answer and then press ENTER/SELECT.
Notes
 The highlighted item has a blue 
background.
Menu Item
MENU >> Sub-menu >>
Highlighted Item

Unavailable Item 
Slider Item 
Sub-menu
Unavailable Sub-menu
Menu Item
Sub-menu
Command 




Inside a menu
Reset Everything
YesNo
Confirmation dialog
   
    
Digital Projection HIGHlite Cine 330 3D Series 
Rev E August 2014  
						

							page 27
Operating Guide
USING THE MENUS
Editing projector settings
If the highlighted menu item is a setting with a list of values to choos\
e from, 
you can change the value in two different ways.
Choosing a value from a list
To access the list of values and then make a selection:
1. Highlight the menu item and press ENTER/SELECT.
2. On the new page that opens, use the UP  and DOWN  arrow buttons 
to highlight a value, then press ENTER/SELECT again. A green “check” 
symbol  marks the current selection.
3. Press MENU to exit the list.
Changing the value without viewing the list
To switch to the next or previous value without viewing the list,
• press the LEFT  or RIGHT  arrow button.
Using a slider to set a value
Some parameters with a numeric value open a slider. To set such a 
parameter:
1. Press the LEFT  or RIGHT  arrow button, or ENTER/SELECT. The 
arrow buttons will open the slider and adjust the value at the same time\
. 
ENTER/SELECT will open the slider without altering the initial value.
2. Use the LEFT  and RIGHT  arrow buttons to move the slider.
When ready, press MENU to exit the slider.
Notes
 Some menu items may not be 
available due to settings in other 
menus. These will be grayed out on 
the actual menu.
List of values
Parameter 101
Slider
Item
Item
MENU >>
Selected Item
Item
Unavailable Item 



Unavailable Item
Item
Item
   
    
Digital Projection HIGHlite Cine 330 3D Series 
Rev E August 2014  
						

							page 28
Operating Guide
A TOUR OF THE MENUS
A Tour Of  The Menus
The projector settings are grouped into six menus as shown in the illust\
ration.
Main menu
Selecting Main from the top level opens the Main menu.
Notes
 See also Using the Menus earlier 
in this guide and  Menu Map later in 
this guide.
Main Menu
IMAGE
MAIN
ADVANCED IMAGE SYSTEM
CONTROL
SERVICE
Presets
Overscan
3D Control
Input Select
Resync
MAIN >>



Off
HDMI 1
Aspect Ratio
Native
   
    
Digital Projection HIGHlite Cine 330 3D Series 
Rev E August 2014  
						

							page 29
Operating Guide
A TOUR OF THE MENUS
Main menu continued from previous page
Aspect Ratio
Choose between 16:9, Theaterscope, 4:3, 4:3 Narrow, 16:10, 5:4 and 
Native.
Notes
Main MenuAspect Ratio
 An anamorphic lens (optional 
accessory) is used with the 
TheaterScope setting, to ensure 
that for a 2.35:1 image, the 
maximum area of the DMD is used, 
giving maximum image brightness.
 The 4:3 Narrow setting is used to 
compensate for the distortion that an 
anamorphic lens would cause to a 
4:3 image.
 For examples of how the different 
aspect ratios affect screen 
dimensions, see  Aspect Ratios 
Explained in the Reference Guide.
Presets
Overscan
MAIN >>
Aspect Ratio 16:9
3D Control
Input Select Theaterscope
4:3
4:3 Narrow
16:10
Resync
5:4
Native
   
    
Digital Projection HIGHlite Cine 330 3D Series 
Rev E August 2014  
						

							page 30
Operating Guide
A TOUR OF THE MENUS
Main menu continued from previous page
Presets
The current image settings can be saved a preset, which you can recall l\
ater. 
The default settings can be recalled at any time as well.
Up to four custom presets can be stored for each  input source you use.
The following settings are saved in a preset:
• From the Main menu — Aspect Ratio and Overscan
• From the Image menu — Brightness, Contrast, Saturation, Hue, 
Sharpness and Noise Reduction
• From the Advanced Image menu — Colorspace, Gamma, 
Color Temperature, Color Gamut, Dynamic Black, 
Adaptive Contrast, RGB Offsets and RGB Gains.
To save a preset:
1. From the Main menu, open Presets.
2. Highlight Save Preset on the left and then move to the list on the right. 
Select the preset you wish to save and press ENTER/SELECT.
To recall a saved preset:
1. From the Main menu, open Presets.
2. Highlight Recall Preset on the left and move to the list on the right. 
Select the preset you wish to recall, then press ENTER/SELECT.
Press MENU to leave the Presets page.
Save Preset
MAIN >> Presets >>
Recall PresetPreset A
Preset B
Preset C
Preset D
Default
2
PIC
MUTE4
B
SHARP
O -SCANNRGAMMA
C-TEMPTESTBRI -C
3D
SWAP3 D
FORMAT2 D /3 D
ENTER
SOURCE
3
6
1
ASPECT
RATIO
MENU
USER
MEMORY
CA
|
ON POWER OFF
User Memory buttons on 
the remote
Notes
Main Menu Presets
 Settings are saved ONLY for the 
current input source.
 Preset D is only accessible through 
the Presets  page of the menu or 
via a protocol command, and not 
through the remote.
  For information on protocol 
commands, see the Remote 
Communications Guide .
   
    
Digital Projection HIGHlite Cine 330 3D Series 
Rev E August 2014  
						

							page 31
Operating Guide
A TOUR OF THE MENUS
Main menu continued from previous page
Overscan
This setting, if switched on, removes unwanted artefacts from the edges \
of 
your image by cropping the edges or increasing the size of the image to \
force 
the edges off-screen.
Unwanted artefacts along the image edges usually occur when the projecto\
r 
is connected to a low quality input souce.
Choose from Off, Crop or Zoom.
Notes
Main MenuOverscanPresets
Overscan
MAIN >>
Off
3D Control
Input Select Crop
Zoom
ResyncAspect Ratio
   
    
Digital Projection HIGHlite Cine 330 3D Series 
Rev E August 2014  
						

							page 32
Operating Guide
A TOUR OF THE MENUS
3D Control
Use this sub-menu to enable, disable and set up 3D input, as follows:
• 3D Format — Off, Auto, Side by Side (Half), Top and Bottom, 
Dual-Pipe, Frame Sequential.
• 3D Swap — Normal and Reverse (set to Reverse if the 3D images are 
displayed in the wrong order)
• Dark Time — 0.65 ms, 1.3 ms, 1.9 ms and 2.5 ms. Set to reduce the 
effect of images overlapping whilst the glasses are switching
• Sync Delay — set to compensate for signal processsing delays in the 
projector.
Notes
Main Menu3D Control
 3D video is only possible on the 
HDMI inputs.
 Set 3D Format to Auto to display 
the Frame Packing format.
 Set the Dark Time to the value 
appropriate to the glasses or 
ZScreen.
  1.9 ms and 2.5 ms Dark Time 
settings are unavailable when 3D 
content is displayed at 144Hz.
 Adjust the Sync Delay to eliminate 
ghosting and achieve a smooth 
grayscale.
  For additional information on 3D 
settings and a list of supported 3D 
formats, see the Reference Guide.
3D Swap
Dark Time
MAIN >> 3D CONTROL
3D Format
Auto
Side by Side (Half)
Top and BottomOff
Sync DelayDual-Pipe
Frame Sequential
   
    
Digital Projection HIGHlite Cine 330 3D Series 
Rev E August 2014