Digital Projection Projector E-Vision 7500 Series User Manual

Digital Projection E-Vision 7500 Series  THE OPERATION COMMANDS Remote Communications Guide
65
...continued from previous page
Notes
ALIGNMENT menu
proj.mode= ?0 = Front
1 = Rear
2 = Ceiling + Front
3 = Ceiling + Rear
Not applicable in STANDBY mode.
fan.pos= ?0 = Normal
1 = Up
2 = Down
Not applicable in STANDBY mode.
zoomio+ -+ = Zoom out
- = Zoom in
Motor command. Not applicable in STANDBY 
mode.
focus+ -+ = Focus Near
- = Focus Far
Motor command. Not applicable in STANDBY 
mode.
vert.offset+ -+ = Up
-...

Digital Projection E-Vision 7500 Series  THE OPERATION COMMANDS Remote Communications Guide
66
...continued from previous page
Notes
proj.ctrl= ?0 = RS232 only
1 = RJ45 only
2 = RS232 + RJ45
Not applicable when Eco Network Power is on.
net.ipaddr= ?
net.subnet= ?
net.gateway= ?
net.dhcp= ?0 = Off
1 = On
startup.logo= ?0 = Off
1 = On
trig.1= ?0 = 5:4
1 = 4:3
2 = 16:10
3 = 16:9
4 = 1.88
5 = 2.35
6 = Letterbox
7 = Native
8 = Unscaled
9 = Auto
If trig.1 is set to Auto, the projector will start 
sending the...

Digital Projection E-Vision 7500 Series  THE OPERATION COMMANDS Remote Communications Guide
67
...continued from previous page
Notes
SERVICE menu
model?
ser.no?
sw.ver?
pixel.clock?In MHz
Not applicable in STANDBY mode or without signal 
locked.
signal?Not applicable in STANDBY mode or without signal 
locked.
h.refresh?Not applicable in STANDBY mode or without signal 
locked.
v.refresh?Not applicable in STANDBY mode or without signal 
locked.
lamp1.hours?
lamp2.hours?
proj.runtime?
blue.only= ?0 = Off
1...

Digital Projection E-Vision 7500 Series  ERROR CODES Remote Communications Guide
68
Error Codes
CodeNameDescription
0000ErrNormalNo Error
0101ErrFmtInitFailDMD Init Fail
0102ErrFmtDADFailDAD1000 detected thermal or voltage fault
0103ErrFmtPMDFailCannot initialize PMD1000
0104ErrFmtSEQFailCannot enable sequencer
0201ErrLamp1InitFailLamp 1 Init fail (at ignition stage)
0202ErrLamp1LitFailLamp 1 lit fail (lamp is accidentally off)
0203ErrLamp1OverTempLamp 1 over temperature
0204ErrLamp1OvpLamp 1 over...

Digital Projection E-Vision 7500 Series  ERROR CODES Remote Communications Guide
69
...continued from previous page
CodeNameDescription
0631ErrFan4InitFail
0632ErrFan4Rotate
0633ErrFan4SpeedFan 4 speed error
0641ErrFan5InitFail
0642ErrFan5Rotate
0643ErrFan5SpeedFan 5 speed error
0651ErrFan6InitFail
0652ErrFan6Rotate
0653ErrFan6SpeedFan 6 speed error
0661ErrFan7InitFail
0662ErrFan7Rotate
0663ErrFan7SpeedFan 7 speed error
0671ErrFan8InitFail
0672ErrFan8Rotate
0673ErrFan8SpeedFan 8 speed error...

Digital Projection E-Vision 7500 Series  ERROR CODES Remote Communications Guide
70
...continued from previous page
CodeNameDescription
0802ErrCwCoverOpenColor Wheel cover open
0803ErrCwInitColor Initial setting fail
1011ErrInletSensorFailAir Inlet temp sensor (T1) error
1012ErrInletSensorOverTempT1 over temperature
1031ErrDMDSensorFailDMD temp sensor (T2) error
1032ErrDMDSensorOverTempDMD (T2) over temperature
1041ErrInlet2SensorFailAir Inlet temp sensor (T3) error
1042ErrInlet2SensorOverTempT3 over...

Digital Projection E-Vision 7500 Series  ERROR CODES Remote Communications Guide
71
...continued from previous page
CodeNameDescription
2902ErrFanDriver1CommFailFan Driver 1 (IC9800) communication fail
2911ErrFanDriver2InitFailFan Driver 2 (IC9805) Init fail
2912ErrFanDriver2CommFailFan Driver 2 (IC9805) communication fail
2921ErrFanDriver3InitFailFan Driver 3 (IC21) Init fail
2922ErrFanDriver3CommFailFan Driver 3 (IC21) communication fail
2931ErrFanDriver4InitFailFan Driver 4 (PSOC) Init fail...

Digital Projection E-Vision 7500 Series  THE KEY COMMANDS Remote Communications Guide
72
The Key Commands
Corresponding remote control key
power.onPOWER ON
power.offPOWER OFF
menuMENU
exitEXIT
enterENTER
upUP
downDOWN
leftLEFT
rightRIGHT
nopno operation (checking if projector is available)
Notes
 An input command will return 
“NA” when the input command is 
not applicable in some specific 
conditions. 
Rev D July 2014  

Digital Projection E-Vision 7500 Series  WEB CONFIGURATION UTILITY Remote Communications Guide
73
Web Configuration Utility
Use the embedded Web Configuration Utility 
to control the projector via a LAN network:
1. Make sure the projector is connected to a 
remote computer via LAN.
2. From the remote computer, access the 
default LAN IP address of the projector. 
The Web Configuration Utility opens.
1 Projector Info
Shows projector and network 
information.
2 Alert Mail Settings
Allows you to set up...

Digital Projection E-Vision 7500 Series  WEB CONFIGURATION UTILITY Remote Communications Guide
74
Email settings
To set up email alerts:
1. Navigate to the Alert Mail Settings tab 1.
2. Enter SMTP settings, email addresses and 
preferences as required.
For assistance with your network settings, consult 
your network administrator.
1
Notes 
Rev D July 2014