Digital Projection Projector E-Vision 7500 Series User Manual

Digital Projection E-Vision 7500 Series  USING THE MENUS Operating Guide
35
Submenus
• Select a submenu using
 and.
• then open the submenu by pressing 
ENTER.
The submenu appears to the right side 
of the menu it was called from. 
The name of the submenu is shown at 
the top.
• To close the submenu, press MENU.
Sometimes, a submenu leads to a sub-
submenu:
• Select the sub-submenu using
 and.
• then open it by pressing ENTER.
The sub submenu appears below the 
submenu it was called from.
The name of the...

Digital Projection E-Vision 7500 Series  USING THE MENUS Operating Guide
36
Selecting parameters
Most parameters are changed by selecting from a list:
• Select from the list using
 and .
• The change will usually be made immediately.
Sometimes you can open the list in the same way you 
open a submenu.
• Press ENTER to open the list.
The list appears to the right of the menu it was 
called from. 
• The item that is currently selected is marked with a 
block: .
• Select from the submenu using
 and.
• The...

Digital Projection E-Vision 7500 Series  USING THE MENUS Operating Guide
37
Sliders
• Use  or to adjust the value.
The menu will disappear, to be replaced by a slider bar.
• To return to the menu, press MENU.
Commands
• To execute the command, press ENTER.
In this example,
• use  or to move the blue highlight to OK or Cancel,
• then press ENTER to confirm your selection.
MENU1MENU2 MENU3
MENU4 MENU
5
MENU6Submenu Enter
Selection 
Slider 
Command Execute
Slider 100
MENU1
MENU2MENU3
MENU4 MENU
5...

Digital Projection E-Vision 7500 Series  A TOUR OF THE MENUS Operating Guide
38
A Tour Of  The Menus
INPUT menu
Input Selection
• Press ENTER to open the Input Selection menu, then select an 
input from the list.
Notes
 See also Using the Menus, earlier 
in this guide and  Menu Map, later in 
this guide.INPUTPICTURELAMPSALIGNMENTCONTROLSERVICEInput Selection EnterTestPattern EnterColorSpace InputLock Background AutoSync Adjust 
INPUTPICTURELAMPSALIGNMENTCONTROLSERVICEInputSelection EnterTestPattern...

Digital Projection E-Vision 7500 Series  A TOUR OF THE MENUS Operating Guide
39
INPUT menu continued
Test Pattern
• Press ENTER to display a Test Pattern.
• Use  or to scroll through the following Test Patterns:
... Off, Color Bar, Crosshatch, Burst, Red, Green, Blue, White, Black, H Ramp, Uncorrected Red, Uncorrected Green, Uncorrected Blue, Uncorrected White, Uncorrected Black, 
Off  ...
• To return to viewing the image from your image source, 
use  or to scroll through the list to Off.
Color Space
•...

Digital Projection E-Vision 7500 Series  A TOUR OF THE MENUS Operating Guide
40
PICTURE menu
Picture Mode
• Select one of the Picture modes as required.
Contrast, Brightness, Saturation, Hue
• Adjust the sliders for these settings, as required.
Gamma
• Select one of the Gamma settings as required.
INPUTPICTURELAMPSALIGNMENTCONTROLSERVICEPictureMode Contrast Brightness Saturation Hue Gamma Color EnterSharpnessNoiseReduction Aspect Ratio Overscan VGASetup EnterAutosync Execute
Notes
 See also Using the...

Digital Projection E-Vision 7500 Series  A TOUR OF THE MENUS Operating Guide
41
PICTURE menu continued
Color submenu
• Press ENTER to open the Color submenu.
Color Temperature
• Native gives you the brightest possible image. 
• A value between 5000K and 9300K selects the relevant color 
temperature.
Trim
• Set the Red, Green and Blue Lift and Gain settings, to improve the 
appearance of the projected image.
Hue, Saturation, Gain
• Set the Red, Green, Blue, Cyan, Magenta and Yellow settings as 
required....

Digital Projection E-Vision 7500 Series  A TOUR OF THE MENUS Operating Guide
42
PICTURE menu continued
Aspect Ratio
• Set Aspect Ratio to suit the incoming video 
signal.
The 5:4, 4:3, 16:10, 16:9, 1.88:1 and 2.35:1 
settings will stretch the image to the selected 
aspect ratio, leaving black bars at the top and 
bottom or sides of the screen, depending on 
the aspect ratio of the projector.
The Letterbox setting can be used where 
a wide screen image has been supplied in a 
narrower format with black...

Digital Projection E-Vision 7500 Series  A TOUR OF THE MENUS Operating Guide
43
PICTURE menu continued
Overscan
• Set this to Off, On or Zoom as required.
VGA Setup submenu
• Press ENTER to open the VGA Setup submenu.
H Total, H Star t, H Phase, V Star t
• Adjust the sliders for these settings, as required to suit the incoming \
image.
Auto Sync
• Press ENTER to force the projector to re-synchronise with the input 
signal.
Notes
 Overscan is used to compensate 
for noisy or badly defined image 
edges,...

Digital Projection E-Vision 7500 Series  A TOUR OF THE MENUS Operating Guide
44
LAMPS menu
Mode
• Set this to Dual, Lamp 1, Lamp 2 or Single as required.
When the mode is changed, it will not be possible to change it again 
within five minutes.
Power
• Set this to Normal for 100% power, Eco for 80% power or Custom 
to enable the Custom Power slider.
High Altitude Mode
• Set this to On if it is necessary to have the cooling fans running at 
high speed.
Custom Power Level
• Set the slider as required.
Lamp...