Digital Projection Projector E-Vision 7500 Series User Manual

Digital Projection E-Vision 7500 Series  PROJECTOR OVERVIEW Installation and Quick-Start Guide
5
Remote control
1 Power ON/OFF
2 Lens controls
3 Menu controls
Press MENU to open the OSD, then use the buttons to 
navigate.
When the OSD is closed, ENTER opens lens controls.
4 INPUT
Select input source.
5 AUTO SYNC
Re-synchronise with the current input signal.
6 OVERSCAN
Select from Off, Crop and Zoom.
7 3D MODE
Access 3D settings.
8 CLEAR
Use only with ID SET.
9 PICTURE
Open the Picture menu.
10 FREEZE...

Digital Projection E-Vision 7500 Series  PROJECTOR OVERVIEW Installation and Quick-Start Guide
6
12 TEST PATTERN
Open the list of available test patterns.
13 NETWORK
Access network settings.
14 ASPECT
Change the aspect ratio.
15 BLANK
Image mute.
16 LAMP MODE
Open the Lamps menu.
17 INFO
Open the Ser vice menu.
18 LIGHT
Illuminate the buttons on the remote control for 10 seconds.
19 ID SET
Hold for 5 seconds to view ID status.
COMBINATION: ID SET + number
Set the ID (Hold for 5 seconds)
COMBINATION: ID...

Digital Projection E-Vision 7500 Series  PROJECTOR OVERVIEW Installation and Quick-Start Guide
7
Control panel
1 POWER
Off or Standby.
2 INPUT
Select input source.
3 AUTO SYNC
Re-synchronise with the current input signal.
4 ASPECT
Change the aspect ratio.
5 SHUTTER
6 Menu controls
7 Lens controls
Indicators
POWER off = NO POWER
 green = normal RUNNING mode red = STANDBY mode
	 flashing	green = PROJECTOR WARM UP
 flashing	amber = PROJECTOR COOL DOWN 
STATUS off = NO ERROR
 flashing	red	(1	flash) = COVER...

Digital Projection E-Vision 7500 Series  CHANGING THE LENS, LAMPS, FILTERS AND COLOR WHEEL Installation and Quick-Start Guide
8
Changing The Lens, Lamps, Filters And Color Wheel
Fitting the lens
1. Remove the lens cap.
2. Position the lens so that the labels are at the top, and gently insert i\
t all 
the way into the lens mount.
3. Push the lens in firmly, and turn it clockwise until it clicks into place.
Removing the lens
1. Push in the lens release lever, and turn the lens anti-clockwise.
2. Remove...

Digital Projection E-Vision 7500 Series  CHANGING THE LENS, LAMPS, FILTERS AND COLOR WHEEL Installation and Quick-Start Guide
9
Changing a lamp
1. Unscrew the two captive screws securing the cover for the lamp that needs changing.
2. Open the lamp compartment.
3. Unscrew the three captive screws securing the lamp module.
4. Pull firmly on the handle to remove the lamp module.
5. Insert a new lamp module and fasten the screws.
6. Replace the lamp compartment cover and fasten the screws.
Notes
 Always...

Digital Projection E-Vision 7500 Series  CHANGING THE LENS, LAMPS, FILTERS AND COLOR WHEEL Installation and Quick-Start Guide
10
Changing the filters
1. Press the air filter covers, then pull them out as shown in Fig. 1.
2. Pull out the old filters as shown in Fig. 2.
3. Insert the new filters and close the filter covers as shown in Fig. 3.
Notes
 The projector will shut down if any 
of the covers are opened whilst in 
operation.
 The filters should be changed at the 
same time as the lamp is changed....

Digital Projection E-Vision 7500 Series  CHANGING THE LENS, LAMPS, FILTERS AND COLOR WHEEL Installation and Quick-Start Guide
11
Changing the color wheel
1. Unscrew the captive screw securing the color wheel compartment cover (Fig. 1) and open the compartment.
2. Unscrew the four captive screws securing the color wheel (Fig. 2).
3. Remove the color wheel (Fig. 3).
4. Insert a new color wheel (Fig. 4) and fasten the screws (Fig. 5).
5. Replace the cover and fasten the screw (Fig. 6).
Notes
 The lamp and...

Digital Projection E-Vision 7500 Series  POSITIONING THE SCREEN AND PROJECTOR Installation and Quick-Start Guide
12
Notes
 Always allow the lamp to cool for 
5 minutes before:
  - disconnecting the power 
- moving the projector
 Ensure that there is at least 70 
cm (28 in) of space between the 
ventilation outlets and any wall, 
and 50 cm (20 in) on all other 
sides.
  If ceiling mounting, ensure there 
is 30 cm (12 in) of space between 
the projector and ceiling.
 Backup safety chains or wires 
should...

Digital Projection E-Vision 7500 Series  OPERATING THE PROJECTOR Installation and Quick-Start Guide
13
Operating The Projector
Switching the projector on
1. Connect the power cable between the mains supply and the projector . Switch on at the switch next to the power connector.
2. Wait until the self-test has completed and the Power indicator on the projector control panel shows red. The lamp will be off and the 
projector will be in STANDBY mode.
3. Press POWER  on the control panel or POWER ON on the...

Digital Projection E-Vision 7500 Series  OPERATING THE PROJECTOR Installation and Quick-Start Guide
14
Adjusting the lens
Zoom
• Use the ZOOM +/− buttons on the control panel or on the remote control to adjust the 
lens so that the image fills the screen.
or use Lens Control in the ALIGNMENT menu.
Focus
• Use the FOCUS +/− buttons on the control panel or on the remote control to adjust the 
lens until the image is sharp.
or use Lens Control in the ALIGNMENT menu.
Shift
• Use the LENS SHIFT buttons , ,...