Digital Projection Projector E-Vision 7500 Series User Manual

							Digital Projection E-Vision 7500 Series  THE OPERATION COMMANDS Remote Communications Guide
65
...continued from previous page
Notes
ALIGNMENT menu
proj.mode= ?0 = Front
1 = Rear
2 = Ceiling + Front
3 = Ceiling + Rear
Not applicable in STANDBY mode.
fan.pos= ?0 = Normal
1 = Up
2 = Down
Not applicable in STANDBY mode.
zoomio+ -+ = Zoom out
- = Zoom in
Motor command. Not applicable in STANDBY 
mode.
focus+ -+ = Focus Near
- = Focus Far
Motor command. Not applicable in STANDBY 
mode.
vert.offset+ -+ = Up
- = Down
Vertical Lens Shift
Motor command. Not applicable in STANDBY 
mode.
horiz.offset+ -+ = Right
- = Left
Horizontal Lens Shift
Motor command. Not applicable in STANDBY 
mode.
lens.load=1 ~ 10Lens Memory Load
Not applicable in STANDBY mode.
lens.save=1 ~ 10Lens Memory Save
Not applicable in STANDBY mode.
lens.center(execute)Not applicable in STANDBY mode.
v.keystone= ? + --80 ~ +80Not applicable in STANDBY mode.
CONTROL menu
eco.net.pow= ?0 = Off (Standard Standby Mode)
1 = On (ECO Standby Mode)
Eco Network Power
auto.powoff= ?0 = Off 
1 = On
Not applicable in STANDBY mode.
auto.powon= ?0 = Off 
1 = On
continued on next page...
Notes 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  THE OPERATION COMMANDS Remote Communications Guide
66
...continued from previous page
Notes
proj.ctrl= ?0 = RS232 only
1 = RJ45 only
2 = RS232 + RJ45
Not applicable when Eco Network Power is on.
net.ipaddr= ?
net.subnet= ?
net.gateway= ?
net.dhcp= ?0 = Off
1 = On
startup.logo= ?0 = Off
1 = On
trig.1= ?0 = 5:4
1 = 4:3
2 = 16:10
3 = 16:9
4 = 1.88
5 = 2.35
6 = Letterbox
7 = Native
8 = Unscaled
9 = Auto
If trig.1 is set to Auto, the projector will start 
sending the trigger as soon as it is switched on. 
Otherwise the trigger will be sent only when the 
aspect ratio matches this setting.
Not applicable in STANDBY mode.
auto.src= ?0 = Off 
1 = On
Auto Search
Not applicable in STANDBY mode.
dblack= ?0 = Off
1 = On
Dynamic Black
Not applicable in STANDBY mode.
lang= ?0 = English
1 = French
2 = Spanish
3 = German
4 = Portuguese
5 = Chinese Simplified
6 = Chinese Traditional
7 = Japanese
8 = Korean
continued on next page...
Notes 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  THE OPERATION COMMANDS Remote Communications Guide
67
...continued from previous page
Notes
SERVICE menu
model?
ser.no?
sw.ver?
pixel.clock?In MHz
Not applicable in STANDBY mode or without signal 
locked.
signal?Not applicable in STANDBY mode or without signal 
locked.
h.refresh?Not applicable in STANDBY mode or without signal 
locked.
v.refresh?Not applicable in STANDBY mode or without signal 
locked.
lamp1.hours?
lamp2.hours?
proj.runtime?
blue.only= ?0 = Off
1 = On
fact.reset(execute)Factory reset
Miscellaneous commands
power.on(execute)Power on
power.off(execute)Power off (puts projector into Standby mode)
status?0 = standby 
1 = warm up 
2 = imaging 
3 = cooling 
4 = reset
errcode?Returns an error code - refer to the Error Codes 
section below.
Notes 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  ERROR CODES Remote Communications Guide
68
Error Codes
CodeNameDescription
0000ErrNormalNo Error
0101ErrFmtInitFailDMD Init Fail
0102ErrFmtDADFailDAD1000 detected thermal or voltage fault
0103ErrFmtPMDFailCannot initialize PMD1000
0104ErrFmtSEQFailCannot enable sequencer
0201ErrLamp1InitFailLamp 1 Init fail (at ignition stage)
0202ErrLamp1LitFailLamp 1 lit fail (lamp is accidentally off)
0203ErrLamp1OverTempLamp 1 over temperature
0204ErrLamp1OvpLamp 1 over voltage
0205ErrLamp1OverLifeLamp 1 reach end of life
0211ErrLamp2InitFailLamp 2 Init fail (at ignition stage)
0212ErrLamp2LitFailLamp 2 lit fail (lamp is accidentally off)
0213ErrLamp2OverTempLamp 2 over temperature
0214ErrLamp2OvpLamp 2 over voltage
0215ErrLamp2OverLifeLamp 2 reach end of life
0501ErrBal1CommFailBallast 1 communication error
0502ErrBal1OverTempBallast 1 over temperature
0511ErrBal2CommFailBallast 2 communication error
0512ErrBal2OverTempBallast 2 over temperature
0601ErrFan1InitFail
0602ErrFan1Rotate
0603ErrFan1SpeedFan 1 speed error
0611ErrFan2InitFail
0612ErrFan2Rotate
0613ErrFan2SpeedFan 2 speed error
0621ErrFan3InitFail
0622ErrFan3Rotate
0623ErrFan3SpeedFan 3 speed error
continued on next page...
Notes 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  ERROR CODES Remote Communications Guide
69
...continued from previous page
CodeNameDescription
0631ErrFan4InitFail
0632ErrFan4Rotate
0633ErrFan4SpeedFan 4 speed error
0641ErrFan5InitFail
0642ErrFan5Rotate
0643ErrFan5SpeedFan 5 speed error
0651ErrFan6InitFail
0652ErrFan6Rotate
0653ErrFan6SpeedFan 6 speed error
0661ErrFan7InitFail
0662ErrFan7Rotate
0663ErrFan7SpeedFan 7 speed error
0671ErrFan8InitFail
0672ErrFan8Rotate
0673ErrFan8SpeedFan 8 speed error
0681ErrFan9InitFail
0682ErrFan9Rotate
0683ErrFan9SpeedFan 9 speed error
0691ErrFan10InitFail
0692ErrFan10Rotate
0693ErrFan10SpeedFan 10 speed error
06A1ErrFan11InitFail
06A2ErrFan11Rotate
06A3ErrFan11SpeedFan 11 speed error
06B1ErrFan12InitFail
06B2ErrFan12Rotate
06B3ErrFan12SpeedFan 12 speed error
0801ErrCwSpinColor Wheel spin error
continued on next page...
Notes 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  ERROR CODES Remote Communications Guide
70
...continued from previous page
CodeNameDescription
0802ErrCwCoverOpenColor Wheel cover open
0803ErrCwInitColor Initial setting fail
1011ErrInletSensorFailAir Inlet temp sensor (T1) error
1012ErrInletSensorOverTempT1 over temperature
1031ErrDMDSensorFailDMD temp sensor (T2) error
1032ErrDMDSensorOverTempDMD (T2) over temperature
1041ErrInlet2SensorFailAir Inlet temp sensor (T3) error
1042ErrInlet2SensorOverTempT3 over temperature
1102ErrLamp1HousingOpenLamp 1 housing open
111 2ErrLamp2HousingOpenLamp 2 housing open
1201ErrThermalBreak1TrigThermal break1 open
1211ErrThermalBreak2TrigThermal break2 open
1401ErrEepromCommFailEEPROM communication fail
1402ErrEepromChecksumFailEEPROM checksum error
2001ErrMcuI2c1FailDDP4422 I2C Port 0 fail
2002ErrMcuI2c2FailDDP4422 I2C Port 1 fail
2103ErrScalerLoadOsdFailOSD Load fail
2201ErrDigitalRx1InitFailITX6535 Init fail
2202ErrDigitalRx1CommFailITX6535 communication fail
2301ErrAdcInitFailAFE1000 Init fail
2302ErrAdcCommFailAFE1000 communication fail
2701ErrExGpio1InitFailExternal GPIO 1 Init fail
2702ErrExGpio1CommFailExternal GPIO 1 communication fail
2711ErrExGpio2InitFailExternal GPIO 2 Init fail
2712ErrExGpio2CommFailExternal GPIO 2 communication fail
2721ErrExGpio3InitFailExternal GPIO 3 Init fail
2722ErrExGpio3CommFailExternal GPIO 3 communication fail
2901ErrFanDriver1InitFailFan Driver 1 (IC9800) Init fail
continued on next page...
Notes 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  ERROR CODES Remote Communications Guide
71
...continued from previous page
CodeNameDescription
2902ErrFanDriver1CommFailFan Driver 1 (IC9800) communication fail
2911ErrFanDriver2InitFailFan Driver 2 (IC9805) Init fail
2912ErrFanDriver2CommFailFan Driver 2 (IC9805) communication fail
2921ErrFanDriver3InitFailFan Driver 3 (IC21) Init fail
2922ErrFanDriver3CommFailFan Driver 3 (IC21) communication fail
2931ErrFanDriver4InitFailFan Driver 4 (PSOC) Init fail
2932ErrFanDriver4CommFailFan Driver 4 (PSOC) communication fail
3011ErrMotorInitFailMotor Board Init fail
3012ErrMotorCommFailMotor Board communication fail
3101ErrRj45InitFailRJ45 Init fail
3102ErrRj45CommFailRJ45 communication fail
Notes 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  THE KEY COMMANDS Remote Communications Guide
72
The Key Commands
Corresponding remote control key
power.onPOWER ON
power.offPOWER OFF
menuMENU
exitEXIT
enterENTER
upUP
downDOWN
leftLEFT
rightRIGHT
nopno operation (checking if projector is available)
Notes
 An input command will return 
“NA” when the input command is 
not applicable in some specific 
conditions. 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  WEB CONFIGURATION UTILITY Remote Communications Guide
73
Web Configuration Utility
Use the embedded Web Configuration Utility 
to control the projector via a LAN network:
1. Make sure the projector is connected to a 
remote computer via LAN.
2. From the remote computer, access the 
default LAN IP address of the projector. 
The Web Configuration Utility opens.
1 Projector Info
Shows projector and network 
information.
2 Alert Mail Settings
Allows you to set up error warnings 
and regular status reports by email.
3 Crestron
Provides access to projector 
controls
1
2
3
Notes
 If Eco Network Power is set to 
Eco, the LAN connection will be 
disabled when the projector is in 
STANDBY mode. To enable power 
on via LAN, set 
Eco Network 
Power 
to Standard.
  The default LAN IP address is XXX.
XXX.X.XXX
  If you suspect this has been 
changed, then you can view the 
current 
Network settings in the 
Control Menu.
 For more information about 
connecting the projector via LAN, 
see the Connection Guide . 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  WEB CONFIGURATION UTILITY Remote Communications Guide
74
Email settings
To set up email alerts:
1. Navigate to the Alert Mail Settings tab 1.
2. Enter SMTP settings, email addresses and 
preferences as required.
For assistance with your network settings, consult 
your network administrator.
1
Notes 
Rev D July 2014