Digital Projection Projector E-Vision 7500 Series User Manual

							Digital Projection E-Vision 7500 Series  A TOUR OF THE MENUS Operating Guide
45
ALIGNMENT menu
Projection Mode
• Front and Rear define whether the projector is in front of the screen 
or behind it. 
Set to Ceiling + Front or Ceiling + Rear if the projector is ceiling 
mounted.
Fan Mode
• Adjusts the fan speeds to optimise cooling when the projector is in 
vertical orientation. 
Set to Up or Down as appropriate when projecting lens up or down.
Lens Control
1. Press ENTER to display the Lens Control box. 
2. Press ENTER again to switch between SHIFT and ZOOM/FOCUS 
mode.
3. Use , , and to adjust the lens as necessary.
INPUTPICTURELAMPSALIGNMENTCONTROLSERVICEProjectionMode FanMode LensControl EnterLensMemory EnterCenterLens ExecuteKeystone DigitalAlignment EnterH/VAlignment Enter
ShiftV
Shift H
Enter toZoom/Focus
Lens Control
Zoom
Focus
Enter toShift
Lens Control
Notes
 See also Using the Menus, earlier 
in this guide and  Menu Map, later in 
this guide. 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  A TOUR OF THE MENUS Operating Guide
46
ALIGNMENT menu continued
Lens Memor y submenu
The current lens position, focus and zoom settings can be saved in 
one of ten memories, for later recall.
• Press ENTER to open the Lens Memor y submenu.
Save Memor y
• Press ENTER to open the Save Memory submenu.
• Use and to select from Lens Memor y 1 
to Lens Memor y 10.
• Press ENTER to save the current settings.
Load Memor y
• Press ENTER to open the Load Memory submenu.
• Use and to select from Lens Memor y 1 
to Lens Memor y 10.
• Press ENTER to recall the saved settings.
Center Lens
• Press ENTER to center the lens.
Keystone
• Use the Keystone control to correct for any distortion caused by 
the projector being in a different vertical plane to the screen.
INPUTPICTURELAMPSALIGNMENTCONTROLSERVICEProjectionMode FanMode LensControl EnterLensMemory EnterCenterLens ExecuteKeystone DigitalAlignment EnterH/VAlignment Enter
LensMemoryLoad Memory EnterSaveMemory Enter
Notes
 See also Using the Menus, earlier 
in this guide and  Menu Map, later in 
this guide.
 The Center Lens command must 
be used after a new lens is inserted. 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  A TOUR OF THE MENUS Operating Guide
47
ALIGNMENT menu continued
Digital Alignment submenu
• Press ENTER to open the Digital Alignment submenu.
Digital Zoom, Digital Pan, Digital Scan
• Use and to select a digital alignment control.
• Set the slider as required.
Reset
• Press ENTER to reset all Digital Alignment settings to zero.
H/V Alignment submenu
• Press ENTER to open the H/V Alignment submenu.
H Zoom, V Zoom, H Shift, V Shift
• Use and to select an alignment control.
• Set the slider as required.
Reset
• Press ENTER to reset all H/V Alignment settings to zero.
INPUTPICTURELAMPSALIGNMENTCONTROLSERVICEProjectionMode FanMode LensControl EnterLensMemory EnterCenterLens ExecuteKeystone DigitalAlignment EnterH/VAlignment Enter
DigitalAlignment
Reset Execute
DigitalZoom DigitalPan DigitalScan 
Notes
 See also Using the Menus, earlier 
in this guide and  Menu Map, later in 
this guide.
  H Shift will only work if the image 
has been reduced horizontally using 
H Tuning. Likewise, V Shift will 
only work once V Tuning has been 
applied.INPUTPICTURELAMPSALIGNMENTCONTROLSERVICEProjection Mode FanMode LensControl EnterLensMemory EnterCenterLens ExecuteKeystone DigitalAlignment EnterH/VAlignment Enter
H/VAlignment
Reset Execute
HZoom VZoom HShift VShift  
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  A TOUR OF THE MENUS Operating Guide
48
CONTROL menu
Eco Network Power
• Set this to Standard or Eco as required. In Eco mode, when the 
projector is in STANDBY mode, the LAN connection is disabled.
Auto Power Off
• Set this to On if you want the projector to go into Standby mode 
when no input source is detected for 20 minutes.
Auto Power On
• Set this to On if you want the projector to start up immediately when 
the mains is connected.
• Set this to Off if you want the projector to go into Standby mode 
when the mains is connected. In this case, the projector will not 
start up until the POWER button is pressed on the control panel or 
the remote control.
Projector Control
• Set this to RS232, Network or Both as required.
INPUT
PICTURE LAMPS
ALIGNMENTCONTROL
SERVICEEcoNetwork Power 
Auto Power Off 
Auto Power On 
Projector Control 
Network Enter
Startup Logo 
Trigger 
Auto Search 
Dynamic Black 
3D Enter
Language Enter
Notes
 Eco Network Power must be set to 
Standard if you wish to be able to 
switch the projector on via LAN.
  See also Using the Menus, earlier 
in this guide and  Menu Map, later in 
this guide. 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  A TOUR OF THE MENUS Operating Guide
49
CONTROL menu continued
Network submenu
• Press ENTER to open the Network submenu.
Set DHCP to Off  to enable manual editing of the IP Address, 
Subnet Mask and Gateway fields. If DHCP is On, these fields are 
updated automatically and manual editing is disabled.
Startup Logo
• Set this to On if you want the DP logo to show when the projector is 
first switched on.
Trigger
• Set this to Auto if you want the Trigger output to be activated when 
the projector is first switched on.
• Set this to one of the Aspect Ratio settings, if you want the 
Trigger output to be activated when the projector is switched to 
that aspect ratio.
Auto Search
• When this is set to On, the projector will search for an alternative 
input source when the current input source is disconnected
• When this is set to Off, the projector will show the DP logo when 
the current input source is disconnected.
Dynamic Black
• Set this to On or Off as required.
Notes
 See also Using the Menus, earlier 
in this guide and  Menu Map, later in 
this guide.
 Dynamic Black reduces the overall 
light output for images that contain 
a lot of black. This improves the 
perceived contrast ratio.
INPUT PICTURE LAMPS
ALIGNMENTCONTROL
SERVICEEcoNetwork Power 
Auto Power Off 
Auto Power On 
Projector Control 
Network Enter
Startup Logo 
Trigger 
Auto Search 
Dynamic Black 
3D Enter
Language Enter
Network
IP Address 
Subnet Mask 
Gateway 
DHCP 
Apply Execute 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  A TOUR OF THE MENUS Operating Guide
50
CONTROL menu continued
3D submenu
• Press ENTER to open the 3D menu, then select from the list:
3D Mode
Choose from DLP-Link and IR, or Off to disable 3D.
3D Sync Invert
Set to On or Off as required.
3D Format
Choose from Frame Sequential, Top/Bottom, Side by Side and 
Frame Packing.
INPUT
PICTURE LAMPS
ALIGNMENTCONTROL
SERVICEEcoNetwork Power 
Auto Power Off 
Auto Power On 
Projector Control 
Network Enter
Startup Logo 
Trigger 
Auto Search 
Dynamic Black 
3D Enter
Language Enter
3D
3D Mode 
3D Sync Invert < Off >
3D Format 
L RLR
Frame Sequential
L
R
Frame Packing
L
R
Top-and-Bottom
L R
Side-by-Side
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide. 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  A TOUR OF THE MENUS Operating Guide
51
CONTROL menu continued
Language submenu
• Press ENTER to open the Language Selection menu, then select a 
language from the list.
Notes
 See also Using the Menus, earlier 
in this guide and  Menu Map, later in 
this guide.INPUT PICTURE LAMPS
ALIGNMENTCONTROL
SERVICEEcoNetwork Power 
Auto Power Off 
Auto Power On 
Projector Control 
Network Enter
Startup Logo 
Trigger 
Auto Search 
Dynamic Black 
3D Enter
Language Enter
Language§  EnglishFrançaisEspañolDeutschPortuguês简体中文繁體中文日本語한국어 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  A TOUR OF THE MENUS Operating Guide
52
SERVICE menu
Information
• The first part of the menu is for information only.
Blue Only
• Set this to On or Off as required.
Factor y Reset
• The projector will ask for confirmation before restoring all settings to 
factory defaults.
• When the confirmation box appears, use  or to move the 
blue highlight to OK or Cancel, then press ENTER to confirm your 
selection.
INPUT
PICTURE LAMPS
ALIGNMENT CONTROLSERVICEModel
: DP-9670-SDPHB
Serial Number : C202XXXXY0008
Software Version: MD04-0D01- LD06-RE04-SE02 -PD03-9B03
Active Source : HDMI
Pixel Clock : 148.65 MHz
Signal Format : 1080p/50Hz
H/V Refresh Rate: H: 56.306 kHz V: 50 Hz
Lamp 1Time : 44HRS
Lamp 2Time : 45HRS
Power OnTime : 45HRS
Blue Only 
Factory Reset Enter
Notes
 See also Using the Menus, earlier 
in this guide and  Menu Map, later in 
this guide.
  Do NOT do this unless you are 
sure that you want to restore ALL 
settings to their factory defaults.
Confirm
OKCancel 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  MENU MAP Operating Guide
53
Menu Map
Menu Submenus and Controls
INPUT
Input Selection  HDMI, DVI, VGA, Component/BNC, Display Port, HDBaseT
Test Pattern  Color Bar, Crosshatch, Burst, Red, Green, Blue, White, Black, H Ramp, Uncorrected Red, Uncorrected 
Green, Uncorrected Blue, Uncorrected White, Uncorrected Black, Off
Color Space   Auto, YCbCr, YPbPr, RGB-PC, RGB-Video
Input Lock  Auto, 48Hz, 50Hz, 60Hz
Background  Logo, Blue, Black, White
Auto Sync Adjust  Always, Off, Auto
PICTURE
Picture Mode  High Bright, Presentation, Video
Contrast slider, 0 to 200 (100)
Brightness slider, 0 to 200 (100)
Saturation slider, 0 to 200 (100)
Hue slider, 0 to 200 (100)
Gamma  Video, Linear, Film, Graphics
Color
Color Temperature  Native, 5000K, 6500K, 7800K, 9300K
Trim  Red Lift, Green Lift, Blue Lift, Red Gain, Green Gain, Blue Gain: slider\
s, 0 to 200 (100)
Hue Red, Green, Blue, Cyan, Magenta, Yellow: sliders, 0 to 200 (100)
Saturation Red, Green, Blue, Cyan, Magenta, Yellow: sliders, 0 to 200 (100)
Gain Red, Green, Blue, Cyan, Magenta, Yellow: sliders, 0 to 200 (100)
White Balance Red, Green, Blue: sliders, 0 to 200 (100)
Sharpness slider, 0 to 31 (0)
Noise Reduction slider, 0 to 15 (0)
Aspect Ratio  5:4, 4:3, 16:10, 16:9, 1.88, 2.35, Letterbox, Native, Unscaled
Overscan Off, Crop, Zoom
VGA Setup  H Total, H Start, H Phase, V Start: sliders, 0 to 200 (100)
Auto Sync  Press ENTER to execute
Notes
 Some of the information in this menu 
map is summarised. See the actual 
menu on the projector for full detail.
 Some menu options and controls 
may not be available due to settings 
in other menus. These will be 
shaded grey on the actual menu.
 Where it would be helpful, some 
menu options are described in more 
detail earlier in this operating guide.
 Color Temperature  values depend 
on other settings. 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  MENU MAP Operating Guide
54
LAMPS
Mode  Dual, Lamp 1, Lamp 2, Single
Power  Normal, Eco, Custom Power
High Altitude  Off, On
Custom Power Level 75-100% (100%)
Lamp Status  Information Only: Lamp 1 On, Off     Lamp 2 On, Off
ALIGNMENT
Projection Mode  Front, Rear, Ceiling + Front, Ceiling + Rear
Fan Mode  Normal, Up, Down
Lens Control  Shift, Zoom/Focus
Lens Memory 
Load Memory  Memory 1-10
Save Memory  Memory 1-10
Center Lens  Press ENTER to execute
Keystone
Digital Alignment
Digital Zoom
Digital Pan
Digital Scan
Reset
H/V Alignment
H Zoom
V Zoom
H Shift
V Shift
Reset
Menu Submenus and ControlsNotes
 Some of the information in this menu 
map is summarised. See the actual 
menu on the projector for full detail.
 Some menu options and controls 
may not be available due to settings 
in other menus. These will be 
shaded grey on the actual menu.
 Where it would be helpful, some 
menu options are described in more 
detail earlier in this operating guide. 
Rev D July 2014