Digital Projection Projector E-Vision 7500 Series User Manual

							Digital Projection E-Vision 7500 Series  OPERATING THE PROJECTOR Installation and Quick-Start Guide
15
Switching the projector off
1. Press and hold POWER  on the control panel or POWER OFF on the remote control for 5 seconds.
The lamp will go off, and the Power indicator on the control panel will flash amber for a few seconds whilst the lamp cools.  The Power 
indicator on the control panel will then show red and the projector will\
 be in Standby mode.
2. Switch off at the switch next to the power connector. Disconnect the power cable from the projector.
Notes
 Always allow the lamp to cool for 
5 minutes before:
  - disconnecting the power 
- moving the projector 
Rev D July 2014  
						

							1616 
Rev D July 2014
Digital Projection E-Vision 7500 Series   Installation and Quick-Start Guide 
This page is intentionally left blank.  
						

							E-Vision 7500 Series
High Brightness Digital Video Projector
CONNECTION GUIDE
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  IN THIS GUIDE Connection Guide
IN THIS GUIDE
Signal Inputs And Outputs ........................................................................\
.....19
Supported Signal Input Modes .....................................................................20
Control Connections  ........................................................................\
................23
Wiring Details ........................................................................\
.............................24
Signal inputs and outputs ........................................................................................24
HDBaseT input .....................................................................................................\
...........24
3D sync connection .....................................................................................................\
....24
HDMI input  .....................................................................................................\
.................25
DVI-D .....................................................................................................\
.........................26
DisplayPort .....................................................................................................\
.................27
VGA .....................................................................................................\
............................28
COMPONENT .....................................................................................................\
............28
Control connections  .................................................................................................29
LAN connection .....................................................................................................\
..........29
RS232 Serial control input  ..............................................................................................29
Wired Remote control connection ...................................................................................29
Screen Trigger output  ....................................................................................................\
.29
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  SIGNAL INPUTS AND OUTPUTS Connection Guide
19
Signal Inputs And Outputs
1 HDBaseT
Receives digital input from HDBaseT-compliant 
devices.
2 3D Sync Out
Sync output signal. This may be affected by the 3D 
Sync Invert setting in the CONTROL > 3D menu.
Connect this to your IR emitter or ZScreen.
3 DVI-D
Connect a DVI-D cable to the DVI connector.
4 HDMI
HDMI 1.4 input. Connect an HDMI cable to the 
connector.
5 DisplayPort
DisplayPort 1.2 input. Connect a DisplayPort cable to 
the connector.
6 RGB In
Receives analog signal from a computer. When using 
this input, it is best to use a fully wired VGA cable to 
connect the source to the projector. This will allow the 
source to determine the projector’s capabilities via DDC 
and show an optimized image.
Such cables can be identified as they have a blue 
connector shell.
Use the INPUT > VGA Setup menu.
7 RGB Out
8 Component
RGBHV, RGsB or RGBS
•  Set Color Space in the INPUT menu to Auto or  
RGB-Video.
YPbPr or YCbCr
• Set Color Space in the INPUT menu to YPbPr or 
YCbCr.
Notes
 For a complete listing of pin 
configurations for all signal and 
control connectors, see  Wiring 
Details later in this Guide.
12345
678 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  SUPPORTED SIGNAL INPUT MODES Connection Guide
20
Supported Signal Input Modes
Signal TypeResolutionRefresh 
Rate (Hz)
 COMPONENT 
-  RGBHV 
 COMPONENT 
-    YUV 
 VGA -  RGBHV  VGA - YUV  DVI-D (EIA Timing) 
 HDMI - RGB (EIA 
Timing) 
 HDMI - YUV 8-bit 
(EIA Timing) 
 Display Port (EIA 
Timing) HDBaseT
PC720x40070  
640x48059.94            
640x48072  
640x48075            
640x48085          
800x60056  
800x60060.32            
800x60072  
800x60075            
800x60085.06          
848x48047.95          
848x48059.94          
1024x76860            
1024x76870  
1024x76875.03            
1024x76885.03          
1280x72047.95          
1280x76859.87          
1280x72060  
1280x80059.81          
continued on next page...
Notes 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  SUPPORTED SIGNAL INPUT MODES Connection Guide
21
Signal TypeResolutionRefresh 
Rate (Hz)
 COMPONENT 
-  RGBHV 
 COMPONENT 
-    YUV 
 VGA -  RGBHV  VGA - YUV  DVI-D (EIA Timing) 
 HDMI - RGB (EIA 
Timing) 
 HDMI - YUV 8-bit 
(EIA Timing) 
 Display Port (EIA 
Timing) HDBaseT
1280x96060          
1280x102460.02          
1280x102475.02            
1280x102485.02          
1366x76859.79          
1440x90059.887          
1600x120060            
1920x108047.95          
1680x105059.94          
1920X1200RB60          
1920X120050          
1400x90060  
1400X105060            
Apple Mac640x48066.59            
832x62474.54            
1152x87075  
NTSCNTSC (M, 4.43)59.94
PA LPAL (B,G,H,I)50
PAL (N)50
PAL (M)59.94
SECAMSECAM (M)50
SDTVRGBS50
continued on next page...
Notes 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  SUPPORTED SIGNAL INPUT MODES Connection Guide
22
Signal TypeResolutionRefresh 
Rate (Hz)
 COMPONENT 
-  RGBHV 
 COMPONENT 
-    YUV 
 VGA -  RGBHV  VGA - YUV  DVI-D (EIA Timing) 
 HDMI - RGB (EIA 
Timing) 
 HDMI - YUV 8-bit 
(EIA Timing) 
 Display Port (EIA 
Timing) HDBaseT
1440x480i60        
1440x576i50        
480i59.94
576i50
EDTV480p59.94                  
576p50                  
HDTV1035i60        
1080i50                  
1080i59.94                  
1080i60                  
720p50                  
720p59.94                  
720p60                  
1080p23.98                  
1080p24                  
1080p25                  
1080p29.97                  
1080p30                
1080p50                  
1080p59.94                  
1080p60                  
Notes 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  CONTROL CONNECTIONS Connection Guide
23
Control Connections
1 LAN
• The projector’s features can be controlled via a 
LAN connection, using commands described in the 
Remote Communications Guide.
• Alternatively, use the Web	Configuration	Utility to 
control the projector.
• Crestron RoomView® Express built-in. Enabling 
support staff to remotely take control of classroom 
technology, perform remote system diagnostics, 
track projector usage and log network activity.
• Use a crossed LAN cable to connect directly to a 
computer, or an uncrossed cable to connect to a 
network hub.
2 RS-232
• The projector’s features can be controlled via a 
serial connection, using the control strings described 
in the Remote Communications Guide.
• Use a null-modem cable to connect directly to a 
computer, or a straight cable to connect to a modem.
3 Screen trigger
The Trigger output can be connected to an electrically 
operated screen, automatically deploying the screen 
when the projector is switched on, or activating curtains 
when the aspect ratio is changed.
4 USB
Service port for firmware updates only.
5 Wired remote control
Connect the remote control using the remote control 
cable supplied with the projector.
Notes
 For a complete listing of pin 
configurations for all signal and 
control connectors, see  Wiring 
Details later in this Guide.
  For full details of how to use the 
menu system, see the Operating 
Guide .
 If Eco Network Power is set to 
Eco, the LAN connection will be 
disabled when the projector is in 
STANDBY mode. To enable power 
on via LAN, set 
Eco Network 
Power 
to Standard.
 See  www.crestron.com for 
further information on  Crestron 
RoomView® Express.
  Plugging in the remote control cable 
will disable the infra-red.
1
2345 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  WIRING DETAILS Connection Guide
24
Wiring Details
Signal inputs and outputs
HDBaseT input
RJ45 socket
3D sync connection
Pin 1 +5V
Pin 2 Ground
Pin 3 Stereo sync
Notes
 For full details of all input settings, 
see the INPUT menu in the 
Operating Guide .
HDBaseT input
VESA 3-pin Mini DIN 
Rev D July 2014