Digital Projection Projector E-Vision 7500 Series User Manual

							Digital Projection E-Vision 7500 Series  MENU MAP Operating Guide
55
CONTROL
Eco Network Power   Standard, Eco
Auto Power Off   On, Off
Auto Power On   On, Off
Projector Control   RS232, Network, Both
Network  
IP Address
Subnet Mask
Gateway
DHCP On, Off
Apply Press ENTER to execute.
Startup Logo   On, Off
Trigger   Auto, 5:4, 4:3, 16:10, 16:9, 1.88, 2.35, Letterbox, Native, Unscaled
Auto Search   On, Off
Dynamic Black   On, Off
3D
3D Mode Off, DLP-Link, IR
3D Sync Invert   On, Off
3D Format Frame Sequential, Top/Bottom, Side by Side, Frame Packing
Language   Select from list
SERVICE
Information only:  Model, Serial Number, Software Version, Active Source, Pixel Clock, Signal Format, H/V Refresh 
Rate, Lamp 1 Time, Lamp 2 Time, Power On Time
Blue Only   Off, On
Factory Reset  Press ENTER to execute.
Menu Submenus and ControlsNotes
 Some of the information in this menu 
map is summarised. See the actual 
menu on the projector for full detail.
 Some menu options and controls 
may not be available due to settings 
in other menus. These will be 
shaded grey on the actual menu.
 Where it would be helpful, some 
menu options are described in more 
detail earlier in this operating guide. 
Rev D July 2014  
						

							56 
Rev D July 2014
Digital Projection E-Vision 7500 Series   Operating Guide
This page is intentionally left blank.  
						

							E-Vision 7500 Series
High Brightness Digital Video Projector
REMOTE COMMUNICATIONS GUIDE
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  IN THIS GUIDE Remote Communications Guide
IN THIS GUIDE
Introduction ........................................................................\
................................59
Operation commands ...............................................................................................59
Key commands ..........................................................................................................59
The Operation Commands ........................................................................\
.....60
INPUT menu ...............................................................................................................60
PICTURE menu ..........................................................................................................61
LAMPS menu .............................................................................................................64
ALIGNMENT menu  ....................................................................................................65
CONTROL menu ........................................................................................................65
SERVICE menu ..........................................................................................................67
Miscellaneous commands ........................................................................................67
Error Codes ........................................................................\
.................................68
The Key Commands ........................................................................\
.................72
Web Configuration Utility ........................................................................\
.......73
Email settings ............................................................................................................74
Projector controls .....................................................................................................75
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  INTRODUCTION Remote Communications Guide
59
Introduction
The projector can be controlled by using an external control system or a PC via a LAN or RS232 serial interface, using a terminal-emulation 
program, such as HyperTerminal.
Operation commands
Operation commands simulate menu operations and determine the settings o\
f the projector, and use the following format:
• All commands consist of ASCII text strings starting with the letters ‘op’, and ending with an ASCII Carriage Return character:
op   [CR]
• The  string can take one of the following formats:
Description
Set= Makes the setting take that value.
Get?Asks what the current value is.
The value is returned as an ASCII text string.
Increment+Adds 1 to the current value.
Decrement–Subtracts 1 from the current value.
Execute(none)Performs an action.
Examples
op input.sel = 1 [CR] sets the input signal to DVI
op input.sel ? [CR] asks what is the input signal
op brightness + [CR] increments the brightness setting
op contrast – [CR] decrements the contrast setting
op auto.img [CR]   commands the projector to attempt to re-synchronise to the current input source
Key commands
Key commands duplicate remote control key presses and use the following \
format:
ky [CR]
Examples
ky testpattern[CR] brings up the list of available test patterns (identical to pressing the  TEST PATTERN key on the remote)
ky input[CR]   brings up the list of available input sources (identical to pressing the INPUT  key on the remote)
ky power.off[CR]   switches the projector off (identical to pressing the POWER OFF key on the remote)
Notes
 Details of how to connect to the 
projector, using the serial control 
or LAN inputs, can be found in the 
Connections Guide.
 Spaces in the commands are 
necessary.
  e.g  op input.sel = 1 
NOT opinput.sel=1
 The TCP Port number is 7000.
 The Serial Port settings are:
 ●Baud rate - 115,200 bps
 ●Data length - 8 bits
 ●Stop bits - one
 ●Parity - none
 ●Flow control - none 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  THE OPERATION COMMANDS Remote Communications Guide
60
The Operation Commands
Notes
INPUT menu
input.sel= ?0 = HDMI
1 = DVI
2 = VGA
3 = Component / BNC
4 = DP
Not applicable in STANDBY mode or when Picture 
Mute is On.
pattern= ?0 = Color Bar
1 = Cross Hatch
2 = Burst
3 = Red (TI)
4 = Green (TI)
5 = Blue (TI)
6 = WHITE (TI)
7 = BLACK (TI)
8 = HRamp (TI)
9 = Red (uncorrected)
10 = Green (uncorrected)
11 = Blue (uncorrected)
12 = White (uncorrected)
13 = Black (uncorrected)
14 = Off
Not applicable in STANDBY mode.
color.space= ?0  = Auto
1 = YCbCr (Rec. 601)
2 = YPbPr (Rec. 709)
3 = RGB-PC (0-255)
4 = RGB-Video (16-235)
Not applicable in STANDBY mode or without signal 
locked.
input.lock= ?0  = Auto
1 = 48 Hz
2 = 50 Hz
3 = 60 Hz
Not applicable in STANDBY mode or without signal 
locked.
no.signal= ?0 = Logo
1 = Blue
2 = Black
3 = White
Not applicable in STANDBY mode.
continued on next page...
Notes 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  THE OPERATION COMMANDS Remote Communications Guide
61
...continued from previous page
Notes
PICTURE menu
pic.mode= ?0 = High Bright
1 = Presentation
2 = Video
contrast= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
bright= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
saturat= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
Only valid when the input is Composite or 
S-Video.
tint= ? + -0 ~ 200Hue
Not applicable in STANDBY mode or without signal 
locked.
Only valid when the input is Composite or 
S-Video.
gamma= ?0 = Film
1 = Graphics
2 = Video
3 = Linear
Not applicable in STANDBY mode or without signal 
locked.
color.temp?0 = Native
1 = 5400K
2 = 6500K
3 = 9300K
Not applicable in STANDBY mode or without signal 
locked.
Not applicable when Color Space is set to 
Custom.
Not applicable when edge blending is on.
red.offset= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
green.offset= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
blue.offset= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
red.gain= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
continued on next page...
Notes 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  THE OPERATION COMMANDS Remote Communications Guide
62
...continued from previous page
Notes
green.gain= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
blue.gain= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
sharp= ? + -0 ~ 31Not applicable in STANDBY mode or without signal 
locked.
nr= ? + -0 ~ 15Noise Reduction
Not applicable in STANDBY mode or without signal 
locked.
aspect= ?0 = 5:4
1 = 4:3
2 = 16:10
3 = 16:9
4 = 1.88
5 = 2.35
6 = Letterbox
7 = Native
8 = Unscaled
Not applicable in STANDBY mode or without signal 
locked.
Native aspect ratio is not applicable when zoom is 
set to Zoom.
zoom= ?0 = Off 
1 = Crop 
2 = Zoom
Overscan
Not applicable in STANDBY mode or without signal 
locked.
Zoom is not applicable when aspect ratio is set to 
Native.
h.total= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
Only applicable when the source is either VGA or 
Component.
h.pos= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
h.phase= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
Only applicable when the source is either VGA or 
Component.
v.pos= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
continued on next page...
Notes 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  THE OPERATION COMMANDS Remote Communications Guide
63
...continued from previous page
Notes
auto.img(execute)Auto Sync
Not applicable in STANDBY mode or without signal 
locked.
hsg.r.gain= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
hsg.g.gain= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
hsg.b.gain= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
hsg.c.gain= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
hsg.m.gain= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
hsg.y.gain= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
hsg.r.sat= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
hsg.g.sat= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
hsg.b.sat= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
hsg.c.sat= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
hsg.m.sat= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
hsg.y.sat= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
hsg.r.hue= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
continued on next page...
Notes 
Rev D July 2014  
						

							Digital Projection E-Vision 7500 Series  THE OPERATION COMMANDS Remote Communications Guide
64
...continued from previous page
Notes
hsg.g.hue= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
hsg.b.hue= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
hsg.c.hue= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
hsg.m.hue= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
hsg.y.hue= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
hsg.wr.gain= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
hsg.wg.gain= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
hsg.wb.gain= ? + -0 ~ 200Not applicable in STANDBY mode or without signal 
locked.
LAMPS menu
lamps= ?0 = Dual
1 = Lamp1
2 = Lamp2
3 = Single
Not applicable in STANDBY mode or when lamp is 
cooling.
lamp.mode= ?0 = Standard
1 = Economy
2 = Custom Power Level
Drive
Not applicable in STANDBY mode or without signal 
locked.
lamp.pwr= ?0-31  (75 % ~100.0 %)Not applicable in STANDBY mode or without signal 
locked.
altitude= ?0 = Off
1 = On
High Altitude
Not applicable in STANDBY mode.
lamp1.stat?0 = Off
1 = On
Not applicable in STANDBY mode.
lamp2.stat?0 = Off
1 = On
Not applicable in STANDBY mode.
continued on next page...
Notes 
Rev D July 2014