Digital Projection Lightning 35hd-T, 40hd-t User Manual

105-453B January 2007  Page 3.5
Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual  3. Getting Started
Notes
  For more detailed information 
about all the touch screen 
menus, see the next section: 
Using the menus.
Press the IMAGE button on the Main menu.
Press the CONTRAST, BRIGHTNESS or GAMMA buttons.
Touch and drag the red sliders up and down, or for fi ne adjustment, press the 
arrow heads. •
•
• 

Page 3.6  105-453B January 2007
3. Getting Started  Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual
Switching the power off
Press the LAMP button on the Main menu.
Press LAMP OFF. Hold the button pressed until the button turns to yellow, then 
release.  The lamp power will ramp down to minimum then go off after a further 
3 seconds.
Allow the lamp to cool for 5 minutes.
Push the main power switch downwards to switch off the power.
When the power is switched off, all current settings are retained,...

105-453B January 2007  Page 4.1
4. Using the Menus
Contents
Introduction .......................................................................................................................................... 4.3
Menu structure ................................................................................................................................. 4.4
Show mode...

Page 4.2  105-453B January 2007
4. Using the Menus  Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual
Confi guration menu ......................................................................................................................... 4.20
Networking confi guration ................................................................................................................. 4.20
Ethernet confi guration choices...

105-453B January 2007  Page 4.3
Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual  4. Using the Menus
Introduction
All of the projector’s features can be controlled using:
the menus on the touch screen or 
the same menus on a remote computer using a web browser 
(with the IP address of the projector typed into the browser address fi eld)
None of the menus are ever displayed on the projection screen.
In these instructions, it is assumed that the touch screen is being used, so the 
expressions ‘press...

Page 4.4  105-453B January 2007
4. Using the Menus  Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual
Menu structure
Show mode (p4)
Show mode indicators
Lamp status
Warnings
Input source
LCD screen blank
IP addresses
Menu buttons....
Main menu
Lamp menu (p6)
Controls
Lamp power slider
Menu buttons...
Shutter open
Shutter close
Lamp on
Lamp off
Maximum power
Minimum power
Lamp/lens memories
Lens menu (p8)
Controls
Move
Zoom
Focus
Menu buttons...
Shutter open
Shutter close
Centre
Calibration
Stop all...

105-453B January 2007  Page 4.5
Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual  4. Using the Menus
Show mode
When the projector is fi rst switched on, the control panel will be in Show mode, as 
shown below:
In Show mode, these icons are displayed:
Lamp status
Lamp off  Lamp off  Lamp on  Lamp on
Shutter closed  Shutter open  Shutter closed  Shutter open
Input source
Single/Dual/Twin mode
Notes
  The buttons of the Main menu 
are always visible at the bottom 
of the display, as shown here.
  To...

Page 4.6  105-453B January 2007
4. Using the Menus  Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual
Warnings
If a projector fault is detected, the warning symbol will be displayed, with an 
explanatory message.
LCD screen blank
To blank the LCD screen, press and hold the Digital projection logo at the top of the 
screen for about two seconds. On release, the screen will blank.
To restore the display, press anywhere on the screen.
IP addresses
The IP addresses of the two ethernet ports are shown....

105-453B January 2007  Page 4.7
Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual  4. Using the Menus
Notes
  The buttons of the Main menu 
are always visible at the bottom 
of the display.
  To go back to a previous menu 
option that is no longer visible, 
call up the menu again using 
the appropriate Main menu 
button.
Lamp menu
Press the LAMP button on the Main menu:
Lamp power
To adjust the lamp power, touch and drag the red slider up and down, or for fi ne 
adjustment, press the arrow heads....

Page 4.8  105-453B January 2007
4. Using the Menus  Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual
Notes
 The Lamp/Lens memories 
are useful if you need to swap 
repeatedly and easily between 
the settings for a number of 
different lenses, or venues.
 Stored zoom settings will be 
accurate only if the lens is 
calibrated. (see next page)
Lamp/Lens memories
Press the LAMP/LENS MEMORIES button.
Store
To store the current Lamp power, Shutter status, Lens shift, zoom and focus 
settings for future...