Digital Projection Lightning 35hd-T, 40hd-t User Manual

105-453B January 2007  Page 6.7
Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual  6. Appendix
Electrical
Rear Input  DVI-D single
Side Input  DVI-D single, DVI-D dual, DVI-D single twin or DVI-D dual twin
(for more information, see Input formats, in section 2. Installation)
Pixel clock  single: up to 165MHz, dual: up to 220MHz
Outputs  DVI-D single loop through (from rear input only)
Control inputs  1 x LAN, 1 x Wireless LAN, 1 x RS232 serial
Mains voltage  200-240 VAC (±10%), 50/60Hz (single...

Page 6.8  105-453B January 2007
6. Appendix  Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual
Lens Data
Optical 103-350 103-351 102-451 102-676
throw ratio1.0 :1 fi xed 1.25 - 1.45 :1 zoom 1.45 - 1.8 :1 zoom 1.8 - 2.4 :1 zoom
full DMD image width2.2m - 6.9m
(7.4 - 22.6ft)3.5 - 31m
(11 - 102ft)3 - 25m
(9 - 82ft)2 - 19m
(7 - 62ft)
throw distance2.2m - 6.9m
(7.4 - 22.6ft)5 - 45m
(16 - 148ft)5 - 45m
(16 - 148ft)5 - 45m
(16 - 148ft)
lens shift vertical in pixels*
(vs DMD height)± 400
(± 0.37H)± 540
(±...

105-453B January 2007  Page 6.9
Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual  6. Appendix
Optical 102-677 102-678 104-189
throw ratio2.2 - 3.0 :1 zoom 3.0 - 4.3 :1 zoom 4.3 - 6.0 :1 zoom
full DMD image width2 - 15m
(5 - 49ft)1 - 11m
(4 - 34ft)1 - 8m
(3 - 25ft)
throw distance2.2m - 6.9m
(7.4 - 22.6ft)5 - 45m
(16 - 148ft)5 - 45m
(16 - 148ft)
lens shift vertical in pixels*
(vs DMD height)± 282
(± 0.26H)± 282
(± 0.26H)± 282
(± 0.26H)
lens shift horizontal in pixels*
(vs DMD width)± 172
(± 0.085W)±...

Page 6.10  105-453B January 2007
6. Appendix  Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual
Notes
  Cable complexity and 
interference can be reduced 
by using the Digilink high 
bandwidth optical connection 
system. Contact your dealer for 
more information.
  The analog pins to the right of 
the connector may be fi tted on 
some models, but are unused.
Connections
DVI-D connection
1  TMDS Data 2-
2  TMDS Data 2+
3  TMDS Data 2/4 Shield
4  TMDS Data 4-
5  TMDS Data 4+
6 DDC Clock
7 DDC Data
8...

105-453B January 2007  Page 6.11
Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual  6. Appendix
LAN connection
10BaseT Unshielded Twisted Pair cable
The standard wire colours as as follows:
1  White / Orange stripe
2 Orange
3  White / Green stripe
4 Blue
5  White / Blue stripe
6 Green
7  White / Brown stripe
8 Brown
Crossed cable
(used to connect directly to a computer with no hub or network.)
(Note that only the green and blue pairs are crossed)
1  White / Orange stripe  White / Green stripe  1
2...

Page 6.12  105-453B January 2007
6. Appendix  Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual
Serial control input
1 unused
2 Received Data
3 Transmitted Data
4 Data Terminal Ready
5 Signal Ground
6  Data Set Ready
7 Request To Send
8 Clear To Send
9  unused at present
Null-modem cable
(used to connect the projector to a computer)
RD 2 --- 3 TD
TD 3  ---  2  RD
DTR 4  ---  6  DSR
GND 5 --- 5 GND
DSR 6 --- 4 DTR
RTS 7  ---  8  CTS
CTS 8  ---  7  RTS
Modem settings
Baud rate    38,400 bps
Data...

105-453B January 2007  Page 6.13
Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual  6. Appendix
Using Windows Hyperterminal to connect to the projector
Many features of the projector can be controlled remotely by sending ascii character 
strings to the serial control input, or via a LAN, using the protocol and syntax 
described in the following pages.
If you are using a PC running Windows 95, 98, Me, NT, 2000 or XP, you can send 
the control codes using Windows Hyperterminal. This can usually be...

Page 6.14  105-453B January 2007
6. Appendix  Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual
Remote communications protocol
Version 1.2 Patch A
Each command string sent to the projector should start with character 0x0a and end 
with character 0x0d. If you are using Windows Hyperterminal, then this will be taken 
care of by the Ascii Setup described on the previous page.
Prefi x each command with:
 “[id],[user],[time],[date],[command priority],[projector id],[projector name],”
for example:...

105-453B January 2007  Page 6.15
Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual  6. Appendix
Image Contrast 
Used to set and query image contrast (gain) levels.
CALL   : “image,contrast,write,r,[r level],g,[g level],b,[b level],o,[level],a,[mode]”
   : Where [level] is 0.0 to 2.0 in steps of 0.001
   : and [mode] is either “on” or “off”
   : ‘o’ is overall level - only valid if ‘a’ is set to ‘off’.
   : ‘a’ is auto level control.
RETURNS  : “[msg id],ACK,contrast,r,[r level],g,[g level],b,[b...

Page 6.16  105-453B January 2007
6. Appendix  Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual
Image Orientation 
Used to set and query image orientation.
CALL   : “image,imageorient,write,[orient]”
   : Where [orient] is one of “normal”, “nsfl ip”, “ewfl ip” or “newsfl ip”
RETURNS  : “[msg id],ACK,imageorient,[orient]”
   : OR
   : “[msg id],NAK,imageorient”
CALL   : “image,imageorient,read,[urgency switch]”
NOTE   : Urgency switch is currently ignored (can be set to 0).
RETURNS  : “[msg...