Digital Projection Lightning 35hd-T, 40hd-t User Manual

105-453B January 2007  Page 2.19
Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual  2. Installation
Notes
  This projector does not 
include any image-scaling or 
processing functions. Sources 
presented to the projector can 
only be mapped pixel for pixel 
to the display.
  More information about 
selecting (blanking) and 
positioning of the image can be 
found in section 4. Using the 
menus.
Connecting the projector
This projector is designed to be the projection head of a projection system...

Page 2.20  105-453B January 2007
2. Installation  Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual
Notes
  The side input has priority over 
the rear input:
  Provided a signal is present on 
the side input, this signal will be 
displayed.
Input format, rear input
Single DVI-D
Sources upto 2048x1080 resolution; 24- 60Hz; 8bits per colour.
Input formats, side input
Single DVI-D
Sources upto 2048x1080 resolution;24- 60Hz; 8bits per colour.
(Use MAIN input only)
Dual DVI-D
A single input with...

105-453B January 2007  Page 2.21
Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual  2. Installation
NotesEDID handshaking
If you are using a computer DVI card or other DVI source that obeys the EDID 
handshaking protocol, then the card or source will automatically confi gure itself to 
suit the projector.
If not, then you should refer to the documentation supplied with the DVI source to 
manually set the resolution to 2048 x 1080 or the nearest suitable setting.
Example: setting up the MMS 1000...

Page 2.22  105-453B January 2007
2. Installation  Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual
Notes
  More information about pin 
connections can be found in 
section 6. Appendix.
  Cable complexity and 
interference can be reduced 
by using the Digilink high 
bandwidth optical connection 
system. Contact your dealer for 
more information.
Input connection examples
Single DVI video source
Dual DVI video sourceRear in
Side in
MMS 1000
non DVI video source
non DVI video sourceMain
Rear input...

105-453B January 2007  Page 2.23
Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual  2. Installation
Notes
  More information about pin 
connections can be found in 
section 6. Appendix.
  More information about using a 
browser to control the projector 
can be found in section 4. Using 
the menus.
  More information about pin 
connections and control codes 
can be found in section 6. 
Appendix.
Control connection examples
LAN connection
All of the projector’s features can be controlled via a LAN...

Page 2.24  105-453B January 2007
2. Installation  Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual
Notes
  Use only the power cable 
provided.
  Ensure that the power 
outlet includes a Ground 
connection, as this 
equipment MUST be earthed.
  Handle the power cable 
carefully and avoid sharp 
bends. Do not use a damaged 
power cable.
Power connection
USA power input
Make sure the main power switch is off before connecting the power cable.
Firmly push in the Hubbell connector, then turn clockwise...

105-453B January 2007  Page 3.1
3. Getting Started
Contents
Switching the power on .................................................................................................................... 3.2
Using the touch screen ..................................................................................................................... 3.2
Switching the lamp on ....................................................................................................................... 3.3
Adjusting the...

Page 3.2  105-453B January 2007
3. Getting Started  Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual
Using the touch screen
All of the projector’s features can be controlled using the touch screen.
The Main Menu is shown below. The eight buttons at the bottom of the screen are 
visible whenever the projector is switched on. Buttons and controls relating to the 
Sub Menus will appear above these eight buttons.
Buttons on the touch screen are activated by light short taps using the tip of your 
fi...

105-453B January 2007  Page 3.3
Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual  3. Getting Started
Notes
  Whenever you switch the lamp 
on, the projector will reset 
momentarily, whilst the lamp 
strikes. This is to protect the 
control circuitry from the effects 
of the lamp strike pulse.
  Any settings made before you 
switched the lamp on will be 
retained.
  For more detailed information 
about all the touch screen 
menus, see the next section: 
Using the menus.
Switching the lamp on
Press...

Page 3.4  105-453B January 2007
3. Getting Started  Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual
Notes
  For more detailed information 
about all the touch screen 
menus, see the next section: 
Using the menus.
Adjusting the projected image
If you have no video source connected to the projector, then you can display a test 
pattern as follows:
Press the IMAGE button on the Main menu.
Select a test pattern. •
•
Once you have an image or a test pattern displayed:
Press the LENS button on the...