Digital Projection Lightning 35hd-T, 40hd-t User Manual

105-453B January 2007  Page 6.17
Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual  6. Appendix
Image Colour Temperature Gain 
Used to set and query image colour temperature levels.
CALL   : “image,colourtempgain,write,r,[r level],g,[g level],b,[b level]”
   : Where [level] is 0.0 to 2.0 in steps of 0.001
RETURNS  : “[msg id],ACK,colourtempgain,r,[r level],g,[g level],b,[b level]”
   : OR
   : “[msg id],NAK,colourtempgain”
CALL   : “image,colourtempgain,read,[urgency switch]”
NOTE   : Urgency...

Page 6.18  105-453B January 2007
6. Appendix  Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual
Input Image Window Size 
Used to set and query image input window size.
CALL   : “image,inputimagewindow,write,c,[cols],r,[rows]”
   : Where [cols] is the number of pixels range 640 to DMD size
   : and [rows] is the number of lines range 480 to DMD size.
RETURNS  : “[msg id],ACK,inputimagewindow,c,[cols],r,[rows]”
   : OR
   : “[msg id],NAK,inputimagewindow”
CALL   :...

105-453B January 2007  Page 6.19
Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual  6. Appendix
Input Capture Offset 
Used to set and query image capture offset.
CALL   : “image,inputcaptureoffset,write,c,[cols offset],r,[rows offset]”
   : Where [cols] is the number of pixels offset from centre
   : and [rows] is the number of lines offset from centre.
   : Positive values move the image down and right and negative move
the image up and left.
RETURNS  : “[msg id],ACK,inputcaptureoffset,c,[cols...

Page 6.20  105-453B January 2007
6. Appendix  Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual
Test Patterns 
Used to set and query test patterns.
CALL   : “image,testpattern,write,[pattern name][vertical rate]”
   : Where [pattern name] is one of:
   : black        - Full Screen Black
   : white        - Full Screen White
   : green        - Full Screen Green
   : red          - Full Screen Red
   : blue         - Full Screen Blue
   : checker      - ANSI Checkerboard
   : align        -...

105-453B January 2007  Page 6.21
Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual  6. Appendix
Degamma Table Select 
Used to set and query degamma table settings.
CALL   : “image,degammaselect,write,[table no.][parametric]”
   : Where [table no.] is one of:
   : 0   - Graphics/NTSC
   : 1   - Graphics Enhanced
   : 2   - NTSC Enhanced
   : 3   - PAL/SECAM 2.8
   : 4   - PAL/SECAM Enhanced
   : 5   - Linear
   : 
   : 255 - use parametric value:
   :
   : and [parametric] is in the range 0.01 to...

Page 6.22  105-453B January 2007
6. Appendix  Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual
Picture Mute 
Used to set and query picture mute.
CALL   : “image,picmute,write,[mode]”
   : Where [mode] is one of “on” or “off”
RETURNS  : “[msg id],ACK,picmute,[mode]”
   : OR
   : “[msg id],NAK,picmute”
CALL   : “image,picmute,read,[urgency switch]”
NOTE   : Urgency switch is currently ignored (can be set to 0).
RETURNS  : “[msg id],picmute,[mode]”
   : OR
   : “[msg id],NAK,picmute”
Notes 

105-453B January 2007  Page 6.23
Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual  6. Appendix
Lens Commands
Lens Stop All 
Used to stop all lens motors.
CALL   : “lens,stop,write”
RETURNS  : “[msg id],ACK,stop”
   : OR
   : “[msg id],NAK,stop”
Lens Move 
Used to move lens position left-right, up-down and open/close shutter.
CALL   : “lens,move,write,[axis],[direction],[time],[speed]”
   : Where [axis] is one of:
   : h - horizontal
   : v - vertical
   : f - focus
   : z - zoom
   : s - shutter...

Page 6.24  105-453B January 2007
6. Appendix  Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual
Lens Goto Absolute Position 
Used to move lens to absolute co-ordinates.
CALL   : “lens,goto,write,h,[hpos],v,[vpos],f,[fpos],z,[zpos]”
   : Where hpos, vpos, fpos and zpos are values probably obtained from a 
‘goto read’
NOTE   : Any one or all axis may be driven at the same time.
RETURNS  : “[msg id],ACK,goto”
   : OR
   : “[msg id],NAK,goto”
CALL   : “lens,goto,read,[urgency switch]”
NOTE   : Urgency...

105-453B January 2007  Page 6.25
Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual  6. Appendix
PSU Commands
Lamp On 
Used to turn Lamp on and query Lamp state.
CALL   : “lpsu,on,write,[lamp number]”
NOTE   : Lamp number currently ignored but must be present
   : (can be set to 0).
RETURNS  : “[msg id],ACK,on”
   : “[msg id],NAK,on”
CALL   : “lpsu,on,read,[urgency switch],[lamp number]”
NOTE   : Urgency switch and lamp number currently ignored
   : but must be present (can be set to 0).
RETURNS  :...

Page 6.26  105-453B January 2007
6. Appendix  Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual
Lamp Power 
Used to set and query Lamp power level.
CALL   : “lpsu,power,write,[lamp number],[% power]”
NOTE   : Lamp number currently ignored but must be present
   : (can be set to 0).
RETURNS  : “[msg id],ACK,power”
   : “[msg id],NAK,power”
CALL   : “lpsu,power,read,[urgency switch],[lamp number]”
NOTE   : Urgency switch and lamp number currently ignored but must be 
present (can be set to 0)....