Dell Projector S320/S320wi User Manual

							  
   
 
   
 
 
       
   
       
AUTO SOURCE—Select Off (the default) to lock the current input signal. If 
you press the Source button when the  Auto Source mode is set to  Off, you 
can manually select the input signal. Select  On to auto detect the available 
input signals. If you press the  Source button when the projector is on, it 
automatically finds the next available input signal. 
A
UTO KEYSTONE—Select  On to automatically adjust image distortion caused 
by tilting the projector. 
P
ROJECTOR MODE—Allows you to select the projector mode, depending upon 
how the projector is mounted. 
•Rear Projection-Desktop — The projector reverses the image so that you 
can project from behind a translucent screen. 
• Rear Projection-Wall Mount — The projector reverses and turns the 
image upside down. You can project from behind a translucent screen with 
a wall-mounted projection. 
•Front Projection-Desktop — This is the default option. 
•Front Projection-Wall Mount — The projector turns the image upside 
down for wall-mounted projection. 
S
PEAKER— Select  On to enable the speaker. Select  Off to the disable 
speaker. 
C
LOSED CAPTION— Select  On to enable close caption and activate the closed 
caption menu. Select appropriate cl osed caption options: CC1, CC2, CC3, 
and CC4. 
NOTE: 
1.  Closed caption option is  available for NTSC only. 
2.	  Closed captioning can only be enabled  via S-Video and Composite 
Video inputs. 
S
TARTUP SCREEN—Default is Dell logo as wallpaper. You can also select 
Capture Screen  option to capture the screen display. The following 
message appears on the screen. 
NOTE: To capture a full image, ensure that the input signal connected 
to the projector is at 1024 x 768 resolution. 
T
EST PATTERN—Test Pattern is used to test focus and resolution. 
You can enable or disable the  Test Pattern by selecting  Off, 1,  or 2 . You can 
also invoke the Test Pattern 1 by pressing and holding down 
and 
Using Your Projector  61 
Downloaded From projector-manual.com DELL Manuals 
						

							 
 buttons on the control panel simultaneously for 2 seconds. You can also 
invoke the test pattern 2 by pressi ng and holding down 
and  buttons 
on the control panel simultaneously for 2 seconds. 
Test Pattern 1: 
Test Pattern 2: 
FACTORY RESET—Select and press  to reset all settings to its factory 
default. The below warning message appears: 
Reset items include both computer  sources and Video source settings. 
Using Your Projector 
62 
Downloaded From projector-manual.com DELL Manuals 
						

							  
 
 
             
 
 
 
 
   
 
   LAN SETTINGS—Select and press  to activate LAN settings. The LAN settings 
menu provides the following options: 
WIRELESS AND LAN—Select  Enabled to activate the Wireless and LAN 
function. 
DHCP— If a DHCP server exists in the  network to which the projector is 
connected, the IP address will automatically be acquired when you select 
DHCP On. If DHCP is Off, manually  set the IP Address, Subnet Mask, 
and Gateway. Use 
and to select  the number of IP address, Subnet 
Mask, and Gateway. Key in enter to confirm each number and then use 
and to set the next item. 
IP A
DDRESS—Automatically or manually assigns the IP address to the 

projector connected to the network.
 
S
UBNET MASK—Configure the Subnet Mask of the network connection.
 
G
ATEWAY—Check the Gateway address with your network/system 

administrator if you configure it manually. 
DNS— Check the DNS Server IP addre ss with your network/system 
administrator if you configure it manually. 
S
TORE—Press  to save the changes made in network configuration 
settings. 
NOTE: 
1.  Use  and button to select IP Address, Subnet Mask, 
Gateway, DNS, and Store. 
2.  Press the 
 button to enter IP A ddress, Subnet Mask, Gateway or 
DNS to set the value. (The sel ected option is highlighted in blue) 
a  Use 
and button to select the option.
 
b  Use 

and  button to set the value.
 
c  After the setup is complete, press the 

button to exit. 
Using Your Projector  63 
Downloaded From projector-manual.com DELL Manuals 
						

							  
 
     
   
 
   
   
3.	  After the IP Address, Subnet Mask, Gateway, and DNS is set up, 
select  Store and press 
 button to store the settings. 
4.	  If you select Store  without pressing the Enter button, the system will 
keep the original settings. 
R
ESET—Press  to reset network configuration. 
W
IRELESS SETTINGS—Select and press  to activate wireless settings. The wireless 
settings menu provides the following options: 
WIRELESS—If your projector has been installed the wireless dongle, this 
option is the  Connected. 
DHCP S
ERVER—Allows you to enable DHCP server of the wireless. 
S
TART IP ADDRESS— Automatically or manually assigns the Start IP address 
of the DHCP server to the projector connected to the wireless. 
E
ND IP ADDRESS— Automatically or manually assigns the End IP address of 
the DHCP server to the projector connected to the wireless. 
S
UBNET MASK—Configure the Subnet Mask of the wireless connection. 
G
ATEWAY—Check the Gateway address with your network/system 
administrator if you configure it manually. 
DNS— Check the DNS Server IP addre ss with your network/system 
administrator if you configure it manually. 
S
TORE—Press  to save the changes made in wireless configuration 
settings. 
NOTE: 
1.  Use  and button to select IP Address, Subnet Mask, 
Gateway, DNS, and Store. 
2.  Press the 
 button to enter IP Ad dress, Subnet Mask, Gateway, or 
DNS to set the value. (The sel ected option is highlighted in blue) 
a  Use 
and buttonto select the option.
 
b  Use 

and  button to set the value.
 
c  After the setup is complete, press the 

button to exit. 
Using Your Projector 
64 
Downloaded From projector-manual.com DELL Manuals 
						

							  
   
   
 
   
 
     
 
3.	  After the IP Address, Subnet Ma sk, Gateway, and DNS is set up, 
select  Store and press 
 button to store the settings. 
4.	  If you select Store  without pressing the Enter button, the system will 
keep the original settings. 
R
ESET—Press  to reset wireless configuration. 
M
ENU SETTINGS— Select and press to activate the menu settings. The menu 
settings consists of the following options: 
MENU POSITION—Allows you to change the position of the OSD menu on 
the screen. 
M
ENU TIMEOUT—Allows you to adjust the time for an OSD timeout. By 
default, the OSD disappears afte r 20 seconds of non-activity. 
M
ENU TRANSPARENCY—Select to change the transparency level of the OSD 
background. 
M
ENU LOCK— Select  On to enable the Menu Lock and hide the OSD menu. 
Select  Off to disable the Menu Lock. If you want to disable the Menu Lock 
function and have the OSD disappear, press the  Menu button on the 
control panel or remote control for 15 seconds, and then disable the 
function. 
P
ASSWORD—When Password Protect is enabled, a Password Protect screen 
requesting you to enter a password will be displayed when the power plug is 
inserted into the electrical output and the power for the projector is first 
turned on. By default, this function is  disabled. You can enable this feature 
by selecting  Enabled. If the password has been set before, key in the 
password first and select the function. This password security feature will 
be activated the next time you turn on the projector. If you enable this 
feature, you will be asked to enter the projector’s password after you turn 
on the projector: 
1	  First time password input request: 
Using Your Projector 65 
Downloaded From projector-manual.com DELL Manuals 
						

							 
   
   
 
  
   
   
 
a 
Go to  Menu Settings , press  and then select  Pa s s w o r d to Enabled 
the password settings. 
b	 Enabling the Password function will  pop up a change screen. Key in a 
4-digit number from the screen and press 
. 
S320 Password screen  S320wi Password screen 
c To confirm, enter the password again. 
d If the password verification is succ
essful, you may resume with accessing 
the projector's functions and its utilities. 
2 If you have entered an incorrect password, you will be given another two 
chances. After three invalid attempts, the projector will automatically turn 
off. 
NOTE: If you forget your password,  contact DELL™ or a qualified 
service personnel. 
3	 
To disable the password function, select the Disabled option to close the 
function. 
4 To delete the password, select the Delete option. 
Using Your Projector 
66 
Downloaded From projector-manual.com DELL Manuals 
						

							 
CHANGE PASSWORD—Key in the original password. Then, enter the new 
password and confirm the new password again. 
S320 Change Password screen  S320wi Change Password screen 
POWER SETTINGS—Select and press  to activate power settings. The power 
settings menu provides the following options: 
Using Your Projector  67 
Downloaded From projector-manual.com DELL Manuals 
						

							  
   
   
   
     
   
 
 QUICK SHUTDOWN—Select  On to turn off the projector with a single press of 
the Power button. This function allows the projector to quickly power off 
with an accelerated fan speed. Slightly  higher acoustic noise is expected 
during quick power off. 
NOTE: Before you turn on the projector  again, wait for 60 seconds to 
allow the internal temperature to  stabilize. The projector will take a 
longer time to turn on if you try  to power on immediately. Its cooling fan 
will run at full speed for about 30 seconds to stabilize the internal 
temperature. 
P
OWER SAVING—By default, the projector is set to enter power saving mode 
after 120 minutes of no activity. A warning message appears on screen 
showing a 60 seconds countdown before switching to power saving mode. 
Press any button during the countdown period to stop the power-saving 
mode. 
You can also set a different delay period to enter power saving mode. The 
delay period is the time you want the projector to wait without an input 
signal. 
If an input signal is not detected during the delay period, the projector 
turns off. To turn on the pr ojector press the Power button. 
D
URING STANDBY—Select  Wireless On  or Off  set the Wireless/LAN model 
on/off while the projector is standb y status (default is Wireless Off). 
L
AMP MODE—Allows you to select the  Normal or ECO  or Dynamic  mode. 
Normal mode operates at full power level. ECO mode operates at a lower 
power level which may provide longer  lamp life, quieter operation, and 
dimmer luminance output on the screen. 
D
YNAMIC—Select and press  to activate image care feature. 
L
AMP HOUR RESET—Press and select the  Confirm option to reset the 
lamp hour. 
Using Your Projector 
68 
Downloaded From projector-manual.com DELL Manuals 
						

							    
     
INTERACTIVE SETTINGS—Select and press  to activate Interactive settings. The 
Interactive settings menu provides the following options: 
NOTE: The S320 projector must be installed with a Interactive Module 
Kit if you want to use the Interact ive feature. Refer to "Installing the 
Optional Interactive Module Kit" on page 15. 
I
NTERACTIVE—Default option is  On. Select Off to disable the Interactive 
Pen function. 
NOTE: 
1.	  Ensure that the Interactive P en is connected. See "Connecting With 
Your Interactive Pen" on page 28. 
2.  Interactive Pen cannot be used in the extend mode. 
3.	  Interactivity is supported only in  the following input modes: VGA and 
HDMI from a Computer, and Wireless  Display, LAN Display, or USB 
Display. 
C
HANNEL—Allows you to set the channel selected as  Auto or Manual . 
•Auto 
— Channel is selected automatically. 
•Manual 
— Channel is selected manually . A total of 30 channels are 
available. 
C
ONNECTOR—Allows you to set the connector selection as  Mini USB or 
Wireless/LAN . 
P
EN SETTINGS—Select and press  to activate Pen settings. The Pen 
settings menu provides the following options: 
Using Your Projector  69 
Downloaded From projector-manual.com DELL Manuals 
						

							     
 
 
 
 
 
   
    
 
  
 
 
 
POINTER MOTION—Allows you to select the Pointer Motion mode: 
Normal, Draw, and Stable. 
•Normal 
— In the Normal mode, pressing the Left button of the 
Interactive Pen holds the position of the pointer for a moment. This 
mode is best to use the Interactive Pen like a mouse, i.e., for left click 
and double click function. 
•Draw 
— In Draw mode, the position can move freely for drawing. 
This mode is best for drawing or writing on the screen. 
•Stable 
— In the Stable mode, pressing and holding the Left button of 
the Interactive Pen limits the pointer to vertical or horizontal moves 
only. If the left button is released, the pointer can resume to move 
freely. This mode is best for drawing vertical or horizontal lines on the 
screen. 
C
LICK SPEED—Allows you to set the mouse pause time. This function is 
only available in Normal mode. The available options are: Fast, 
Medium, and Low. 
•Fast 
— Set the pointer motion freeze time to the minimum amount 
of time, 0.5 seconds. 
•Medium 
— Set the pointer motion freeze time to the middle value, 
1.0 seconds. 
•Low 
— Set the pointer motion freeze time to the maximum amount 
of time, 1.5 seconds 
S
ET FUNCTION—Allows you to set the function of the Function button 
on the Interactive Pen. Available options are:  Toggle: 
Normal/Draw/Stable , PowerPoint Annotation , Switch Windows (Alt 
+ Tab) , Esc , Show Desktop (Cmd + D) , Open Windows Explorer 
(Cmd + E) , Middle Mouse , Double Click, and Disable  (See "Using 
the Interactive Pen" on page 40). 
•Toggle: Normal/Draw/Stable — Function as toggling among  Normal, 
Draw,  and Stable  mode. 
•PowerPoint Annotation 
— Function as annotating in the PowerPoint 
slide show. 
Using Your Projector 
70 
Downloaded From projector-manual.com DELL Manuals