Dell Projector S320/S320wi User Manual

							  
   
 Cannot use the Pen in 3D  a Supports the VGA and HDMI output 
source.  signal at 120 Hz only. 
b	  Composite/S-Video output signal at 60 Hz 
and Component output signal are not 
supported. 
Cannot use the Pen in  Composite Video or S-Video source is not 

Composite Video or S-Video  supported.
 
source.
 
Cannot use Nib  If the Nib is worn out, replace with a new Nib. 
When using USB Display, can  Wireless USB function is not supported.
 
Wireless USB function be 

used?
 
Troubleshooting Your Projector 131 
Downloaded From projector-manual.com DELL Manuals 
						

							    
 
 
   
 
   
 
 
 
  
   
 
   
 
 
   
 
     
Guiding Signals
 
Control Buttons  Indicator 
Projector 
Status  Description 
Pow e r TEMP 
(Amber)  LAMP 
(Amber) 
Standby mode  Projector in Standby mode. Ready to 
power on.  BLUE 
Flashing  OFF 
OFF 
Wa r m i n g  u p 
mode  Projector takes some time to warm up 
and power on. 
BLUE 
OFF OFF 
Lamp on  Projector in Normal mode, ready to 
display an image.  Note : The OSD menu is not 
accessed.  BLUE 
BLUE  OFF 
OFF OFF 
OFF 
Cooling mode 
Cooling before 
Po w e r  S a v i n g 
mode  Projector is cooling to shutdown. 
The projector takes  60 seconds to cool 
down before entering Power Saving 
mode.  AMBER 
OFF OFF 
Projector 
overheated  Air vents might be blocked or ambient 
temperature may be above 35 ºC. The 
projector automatically shuts down. 
Ensure that the air vents are not blocked 
OFF AMBER  OFF 
and that the ambient temperature is 
within operational range. If the problem 
persists, contact Dell. 
Lamp driver 
overheated  The lamp driver is overheated. The air 
vents may be blocked. The projector 
automatically shuts down. Turn the 
display on again after the projector cools 
down. If the problem persists, contact 
Dell. 
Fan breakdown  One of the fans has failed. The projector  automatically shuts do wn. If the problem 
persists, contact Dell. 
Lamp driver 
breakdown  The lamp driver has failed. The projector 
automatically shuts 
down. Unplug the 
power cord after three minutes and then 
turn the display on again. If this problem 
persists, contact Dell. 
Color Wheel 
breakdown  Color wheel cannot start. The projector 
has failed and the projector 
automatically shuts 
down. Unplug the 
power cord after three minutes and then 
turn on the projector. If this problem 
persists, contact Dell. 
Lamp failure  Lamp is defective. Replace the lamp. 
Fault  - D C 
supply (+12V)  Power supply has been interrupted. The 
projector automatically shuts down. 
Unplug the power cord after three 
minutes and then turn on the projector. 
If this problem persists, contact Dell. 
Lamp module 
connection 
failed  Lamp module connection may be 
disrupted. Check the lamp module and 
ensure that it is properly installed. If the 
problem persists, contact Dell.  AMBER 
OFF 
AMBER 
Flashing 
BLUE OFF 
AMBER 
Flashing 
OFF  AMBER 
AMBER 
Flashing 
OFF 
AMBER 
Flashing 
OFF 
AMBER 
OFF  OFF 
OFF 
AMBER 
Flashing 
AMBER 
Flashing 
AMBER 
AMBER 
AMBER 
Flashing 
132  Troubleshooting Your Projector 
Downloaded From projector-manual.com DELL Manuals 
						

							    
 
       
   
   
 
 
   
   
   
   
   
 
   
 
Interactive Pen LED Guiding Signals
 
PEN Status  Description  Indicator 
Green color  Amber color  Checking flow and items / times 
Normal Mode 1  Pen faces the screen with 
the link.  Solid ON 
OFF 
Normal Mode 2  Pen doesn’t faces the screen 
but with the link.  Flashing 0.02s 
ON /1s OFF  OFF Will enter Sleep Mode after 3 
minutes 
Search for 
Open network 
mode  When Pen searching for 
open network (Green LED 
flashing twice every 2 sec). 
After holding down Nib and 
Function button for 5 secs, 
the pen will change to this 
mode.  Flashing 0.1s 
ON /0.1s OFF 
& 0.1s ON/1.7s  OFF  OFF 
If the pen doesn't pair with projector 
successfully, the pen will enter Sleep 
Mode after 3 minutes 
Search for Fixed 
network mode  When Pen searching for 
fixed network. 
Flashing 0.3s 
ON /0.3s OFF  OFF If the pen doesn't pair with projector 
successfully, the pen will enter Sleep 
Mode after 3 minutes 
Pairing mode  After holding down 
Function button for 5 secs, 
the Green LED will blink 1 
time each 0.15 secs 
(continued 10 seconds).  Flashing 0.15s 
ON /0.15s OFF  OFF If the pen pair with projector 
successfully, the pen will enter Pair 
successful mode. 
If the pen doesn't pair with projector 
successfully, the pen will enter Pair 
failed mode after 10 seconds. 
Pair successful 
mode  When pen pair with 
projector successfully after 
pairing mode (Green and 
Amber LED will flash 
alternately continued 3 
seconds).  Flashing 0.3s 
ON /0.3s OFF  Flashing 0.3s 
OFF/0.3s ON  Enter pairing mode and pair 
successfully in 10 seconds 
Pair failed mode  When pen pair with  projector failed after pairing 
mode (Green and Amber 
LED will flash at the same  Flashing 0.3s 
ON /0.3s OFF  Flashing 0.3s 
ON /0.3s OFF  Enter pairing mode and pair failed 
after 10 seconds 
time continued 3 seconds). 
Sleep mode  Enter sleep mode for power 
saving purpose. 
Solid ON 3 sec. Solid ON 3 sec. 1. Pen doesn't face the screen but 
with the link: will enter Sleep mode 
after 3 minutes. 
2. After searching for AP channel 3 
cycles without a link, will enter Sleep 
mode. 
Low battery 
capability  The pen battery is low. Two 
hours are left to run out of 
the battery. 
OFF Flashing 1s 
ON/1s OFF  The MSP430 will check battery 
capacity in normal operation. This 
alert LED signal is shown if the 
battery capacity is low. 
Battery is 
exhausted and 
can not run PB  The Photo sensor and RF 
module cannot work 
properly. Pen can not work 
normal. 
OFF 
Solid ON The pen battery is exhausted. Power 
only works for MSP430. The alert 
LED will appear 1 minute to save 
power and then enter Sleep mode. 
Pen cannot be used in this status. 
Battery 
charging when 
battery low  Pen put on the charger or 
connect USB cable by 
Laptop 
N/A 
Solid ON 
Battery 
charging when 
battery full  Pen put on the charger or 
connect USB cable by 
Laptop 
N/A 
OFF 
Troubleshooting Your Projector  133 
Downloaded From projector-manual.com DELL Manuals 
						

							Changing the Lamp
 CAUTION: Before you begin any of the procedures in this section, follow the 
Safety Instructions as described on page 11. 
Replace the lamp when the message "Lamp is approaching the end of its 
useful life in the operation. Replacement suggested! 
www.dell.com/lamps" appears on the screen. If  this problem persists after 
replacing the lamp, contact Dell™. For more information, see Contacting Dell™on 
page 144.
 
CAUTION: Use an original lamp to ensure safe and optimal working condition 
of your projector.
 
CAUTION: The lamp becomes very hot when in use. Do not attempt to replace 
the lamp until the projector has been  allowed to cool down for at least 
30 minutes.
 
CAUTION: Do not touch the bulb or the lamp glass at any time. Projector 
lamps are very fragile and may shatte r if touched. The shattered glass pieces 
are sharp and can cause injury.
 
CAUTION: If the lamp shatters, remove all broken pieces from the projector 
and dispose or recycle accor ding to state, local, or federal law. For more 
information see  www.dell.com/hg. 
1 Turn off the projector and disconnect the power cord.
 
2 Let the projector cool for at least 30 minutes.
 
3 Loosen the two screws that secure  
the lamp cover, and remove the 

cover.
 
4 Loosen the two screws that secure  
the lamp.  
5 Pull the lamp up by  its metal handle.

 
NOTE: Dell™ may require lamps 

replaced under warranty to be 

returned to Dell™. Otherwise,  
contact your local waste disposal 

agency for the address of the  
nearest deposit site.
 
6 Replace with the new lamp.
 
7 Tighten the two screws that secure the lamp.
 
8 Replace the lamp cover and tighten the two screws.
 
Troubleshooting Your Projector 
134 
Downloaded From projector-manual.com DELL Manuals 
						

							  
   
     
   
 
 9 Reset the lamp usage time by selecting "Yes" for  Lamp Reset in the OSD  Po w e r 
Settings of the Advanced Setting menu  (see Power Settings of the Advanced 
Setting menu on page 67). When a new  lamp module has been changed, the 
projector will automatically detect and reset the lamp hours. 
CAUTION: Lamp Disposal (for the US only)
 LAMP(S) INSIDE THIS PRODUCT  CONTAIN MERCURY AND MUST BE 
RECYCLED OR DISPOSED OF ACCORDIN G TO LOCAL, STATE, OR FEDERAL 
LAWS. FOR MORE INFORMATION, GO TO WWW.DELL.COM/HG OR CONTACT 
THE ELECTRONIC INDUSTRIES AL LIANCE AT WWW.EIAE.ORG. FOR 
LAMP-SPECIFIC DISPOSAL INFORMATION, CHECK 
WWW.LAMPRECYCLE.ORG. 
Troubleshooting Your Projector 135 
Downloaded From projector-manual.com DELL Manuals 
						

							 
     
5
 
Specifications
 
Light Valve  0.55" XGA S450 DMD, DarkChip3™
 
Brightness  3000 ANSI Lumens (Max.)
 
Contrast Ratio  2200:1 Typical (Full On/Full Off)
 
Uniformity  80% Typical (Japan Standard - JBMA)
 
Number of Pixels  1024 x 768 (XGA)
 
Aspect Ratio  4:3
 
Displayable Color  1.07 billion colors
 
Color Wheel Speed  2 X
  1 X for 3D Display 
Projection Lens  F-Stop: F/ 2.8 
Effective Focal length=7.26 mm 
Fixed Lens, Digital Zoom only 
Throw ratio =0.626 wide and tele 
Offset Ratio  115±5% 
Projection Screen Size  31.45 ~ 300 inches (diagonal) 
Projection Distance  1.31 ft ~ 12.5 ft (0.4 m ~ 3.82 m) 
Video Compatibility  Composite Video / S-Video: NTSC (J, M, 4.43), PAL  (B, D, G, H, I, M, N), SECAM (B, D, G, K, K1, L) 
Component Video input via VGA: 1080i, 720p, 
576i/p, 480i/p 
HDMI input: 1080p, 720p, 576i/p, 480i/p 
Power Supply  Universal AC 100-240 V 50-60 Hz with PFC input 
Specifications 
136 
Downloaded From projector-manual.com DELL Manuals 
						

							   
 Power Consumption	  Normal mode: 305 W ± 10% @ 110 Vac 
Eco mode: 225 W ± 10% @ 110 Vac 
Power saving mode: 
						

							 
 
  
 
   
   
   
 
Environmental 
I/O Connectors (for 
S320/S320wi)  Operating temperature: 5 ºC - 35 ºC (41 ºF- 95 ºF) 
Humidity: 80% maximum 
Storage temperature: 0 ºC to  60 ºC (32 ºF to 140 ºF) 
Humidity: 90% maximum 
Shipping temperature: -20 ºC to 60 ºC 
(-4 ºF to 140 ºF) 
Humidity: 90% maximum 
Power: One AC power socket (3-pin - C14 inlet) 
VGA input: Two 15-pin D-sub connectors (Blue), 
VGA-A and VGA-B, for analog RGB/Component 
input signals. 
VGA output: One 15-pin D-sub connector (Black) 
for VGA-A loop through. 
S-Video input: One standard 4-pin min-DIN 
S-Video connector for Y/C signal. 
Composite Video input: One Yellow RCA jack for 
CVBS signal. 
HDMI input: One HDMI connector for supporting 
HDMI 1.3. HDCP compliant. 
Analog Audio input: One 3.5 mm stereo mini phone 
jack (Blue). 
Variable audio output: One 3.5 mm stereo mini 
phone jack (Green). 
USB (type B) port: One mini USB slave for remote 
support and Interactive Pen. 
RS232 port: One 9-pin D-sub for RS232 
communication. 
USB (type A) port (embedded for S320wi): One 
USB connector for Photo/PtG viewer (JPG/PPT 
format). 
USB (type B) port (embedded for S320wi): One 
USB connector for supporting USB display. 
RJ45 port (embedded for S320wi): One RJ45 
connector for control of projector through network 
and LAN display. 
Specifications 
138 
Downloaded From projector-manual.com DELL Manuals 
						

							  
   
   
 
   
 
    
     
   
Wirel es s Dongle  Wireless Standard: IEEE802.11b/g/n 
(embedded for S320wi)  Wireless: One WiFi USB (ty pe A) connector for 
supporting wireless dongle (Embedded WiFi, USB 
interface). 
OS environment: Windows 7/Vista/XP/2000, MAC 

OS X
 
Support: Presentation slides and projector control.
 
Allow connection up to 30 users at the same time.
 
4-to-1 split screen. Allows four presentation slides to 

be projected on screen.
 
Conference Control mode.
 
Supports Audio Projection (driver installation may 

be required. Download from support.dell.com). 
Lamp  Philips 240 W user-replaceable lamp 
Lamp life  Without image care 
Normal mode: Up to 3000 hours 
ECO mode: Up to 4000 hours 
With image c are 
Normal mode: Up to 4000 hours 
ECO mode: Up to 5000 hours 
NOTE: The lamp life rating for any projector is a measure of brightness 
degradation only, and is not a specification for the time it takes a lamp to fail 
and cease light output. Lamp life is defi ned as the time it takes for more than 
50 percent of a lamp sample population to have brightness decrease by 
approximately 50 percent of the rated lumens for the specified lamp. The lamp 
life rating is not guaranteed in any wa y. The actual operating life span of a 
projector lamp will vary according to operating conditions and usage patterns. 
Usage of a projector in stressful  conditions which may include dusty 
environments, under high temperatures, many hours per day, and abrupt 
powering-off will most likely result in a lamp’s shortened operating life span or 
possible lamp failure. 
Specifications 139 
Downloaded From projector-manual.com DELL Manuals 
						

							   
 NOTE: All optical performance is measur ed under the condition of the 
Interactive Pen off within user  manual or product specification. 
Specifications 
140 
Downloaded From projector-manual.com DELL Manuals