Dell Projector S320/S320wi User Manual

							3 To power off the projector quickly, press the Power button and hold for 1 second 
while the projector’s cooling fans are still running. 
NOTE: Before you turn on the projector agai n, wait for 60 seconds to allow the 
internal temperature to stabilize. 
4 Disconnect the power cord from the electrical outlet and the projector. 
Adjusting the Projected Image 
Raising the Projector Height 
1 Raise the projector to the desired display angle, and use the front tilt 

adjustment wheel to fine-tune the display angle.
 
2 Use the two tilt adjustment wheels to fine-tune the display angle.
 
Lowering the Projector Height 
1 Lower the projector, and use the front tilt adjustment wheels to fine-tune the 
display angle. 
1 
VGA-OUT  VGA-A IN VGA-B IN HDMI 
USB-A  DOUSB  RJ45 
Composite  S-Video  Mini-USB RS232
Audio-In  Audio-Out 
1　 
2 
1  Front tilt adjustment wheel
 
(Angle of tilt: 0 to 4 degree)
 
2  1x Rear tilt adjustment wheel 
Using Your Projector 31 
Downloaded From projector-manual.com DELL Manuals 
						

							  
  
 
 
   
Adjusting the Projector Focus 

CAUTION: To avoid damaging the projector, ensure that the front tilt 
adjustment wheel is fully retracted bef ore moving the projector or placing the 
projector in its carrying case. 
NOTE: The carrying case is not shipped wit h your projector. You can purchase 
the carrying case (P/N: 8R3VM)  on the Dell website at www.dell.com. 
1 Rotate the focus tab until the image is clear. The projector focuses at distances 
ranging between 1.31 ft to 12.5 ft (0.4 m to 3.82 m). 
1 Fo c u s  r i n g 
1 
Using Your Projector 
32 
Downloaded From projector-manual.com DELL Manuals 
						

							Using Your Projector33
Adjusting Projection Image Size
S320/S320wi300" (762.00 cm)
246" (624.84 cm)
193" (490.22 cm)
139" (353.06 cm)
86" (218.44 cm)
31.45" (79.88 cm)
12.5' (3.82 m)10.1' (3.08 m)7.91' (2.41 m)5.71' (1.74 m)3.51' (1.07 m)1.31' (0.4 m)
VGA-A IN
VGA-OUT VGA-B INHDMI
Audio-In Audio-Out Composite S-Video
Mini-USBRS232RJ45
DOUSB
USB-A
Projector to screen distance
Downloaded From projector-manual.com DELL Manuals 
						

							Dis
ta
n c
e :
  1
.7 4 m 
D
ia
g o
n a
l: 1
3 9
" 
S320/S320wi 
Screen size  Top 
(Min zoom)
 
Desired Distance (m)
 

 
Diagonal (inch)
   From base to top of image (cm) 
W (cm) x H (cm)
   
0.4 31.45  65 x 49
  56
 
1.07  86
 174 x 130
  150
 
1.74  139
 283 x 212
  244
 
2.41  193
 392 x 294
  338
 
3.08  246
 501 x 376
  432
 
3.82  300
 610 x 457
  526
 
* This graph is for user reference only. 
* Offset Ratio: 115±5% 
C 
Height (Hd): 244 cm B 
A 
34
  Using Your Projector 
Downloaded From projector-manual.com DELL Manuals 
						

							 
 
 
 
   
 
 
 
Using the Control Panel
 
1 3 
5 2 
10  4 
7 
6 
9 8 
1  Power  Turns the projector on or off. For more 
information, see "Turning Your Projector On" on 
page 30 and "Turning Your Projector Off" on 
page 30. 
2  Up   / Keystone 
adjustment  Press to navigate through the On-Screen Display 
(OSD) Menu items. 
Press to adjust image distortion caused by tilting 
the projector (+37/-40 degrees). 
3  LAMP warning light  If the LAMP amber indicator is on or blinking, 
one of the following problems could be occurring: 
• Lamp is reaching its end of usable life 
• Lamp module is not properly installed 
• Lamp driver failure 
• Color wheel failure 
For more information, see "Troubleshooting Your 
Projector" on page 126 and "Guiding Signals" on 
page 132. 
Using Your Projector  35 
Downloaded From projector-manual.com DELL Manuals 
						

							   
 
  
 
   
     
4 TEMP warning light	  If the TEMP amber indicator is on or blinking, 
one of the following problems could be occurring: 
•  Internal temperature of the projector is too 
high 
• Color wheel failure 
For more information, see "Troubleshooting Your 
Projector" on page 126 and "Guiding Signals" on 
page 132. 
5  Enter  Press to confirm the selection item. 
6  IR Receiver  Point the remote control towards the IR receiver 
and press a button. 
7  Right   / Auto Adjust  Press to navigate through the On-Screen Display 
(OSD) Menu items. 
Press to synchronize the projector to the input 
source. 
NOTE: Auto Adjust  does not operate if the 
on-screen display (OSD) is displayed. 
8  Down   / Keystone 
adjustment  Press to navigate through the On-Screen Display 
(OSD) Menu items. 
Press to adjust image distortion caused by tilting 
the projector (+37/-40 degrees). 
9  Left  / Source  Press to navigate through the On-Screen Display 
(OSD) Menu items. 
Press to toggle through Analog RGB, Composite, 
Component (YPbPr via VGA), HDMI, and 
S-Video sources when multiple sources are 
connected to the projector. 
10  Menu  Press to activate the OSD. Use the directional 
keys and the  Menu button to navigate through 
the OSD. 
Using Your Projector 
36 
Downloaded From projector-manual.com DELL Manuals 
						

							  
 
 
 1 
24 
Using the Remote Control
 
14 
15 
16 
17 
18  19 
20 
21 
22  23 
25 
26 
ZOOM
ZOOM 
INFO 
VIDEO
VGA 
S-VIDEO 
FREEZE
AUTO ADJ. 
KEYSTONE 
SOURCE 
VIDEO MODE ASPECT
MENU  POWER 
MOUSE 
BLANK 
ENTER 
VOL 
VOL 
MUTE 
11 
12 
13  4 
3 
1 
5 
7 
8 
9 
2 
6 
10 
Turns the projector on or off. For more 
information, see "Turning Your Projector On" on 
page 30 and "Turning Your Projector Off" on 
page 30. 
Po w e r 
Enter 
ENTER Press to confirm the selection. 
3  Right  Press to navigate through the On-Screen Display 
(OSD) Menu items. 
4  Down  Press to navigate through the On-Screen Display 
(OSD) Menu items. 
Using Your Projector  37 
2 
Downloaded From projector-manual.com DELL Manuals 
						

							    
 
     
 
   
 
 
 
   
 
5 
6 
7 
8 
9  Aspect Ratio 
Press to change the aspect ratio of a displayed 
image. 
MUTE Press to mute or un-mute the projector speaker. 
Mute 
Video mode	  The projector has preset configurations that are 
optimized for displaying data (presentation 
slides) or video (movies, games, etc.). 
Press the  Video Mode  button to toggle between 
Presentation mode , Bright mode , Movie mode , 
sRGB , or Custom mode . 
Pressing the  Vi d e o  M o d e  button once will show 
the current display mode. Pressing the  Vi d e o 
Mode  button again will switch between modes. 
Press to move to the previous page. 
Mouse up 
NOTE: The Mini USB cable must be 
connected if you want to use the Page Up 
feature. 
Press to move to the next page. 
Mouse down 
NOTE: The Mini USB cable must be 
connected if you want to use the Page Down 
feature. 
10  Freeze  Press to pause the screen image, then press 
"Freeze" again to unfreeze the image. 
11  Blank screen  Press to hide/unhide the image. 
12  Information  Press to provide projector native resolution 
information. 
13  S-Video  Press to choose S-Video source. 
14  Up  Press to navigate through the On-Screen Display 
(OSD) Menu items. 
Press to navigate through the On-Screen Display 
Left 
(OSD) Menu items. 
16  Menu  Press to activate the OSD. 
17  Vo l u m e  u p 
Press to increase the volume. 
18  Source  Press to switch between Analog RGB, Composite, 
Component (YPbPr, via VGA), HDMI, and 
S-Video source. VOL 
Using Your Projector 
38 
15 
Downloaded From projector-manual.com DELL Manuals 
						

							  
  VOL19 Vo l u m e  d o w n Press to decrease the volume. 
20  Keystone adjustment +  Press to adjust image distortion caused by tilting 
the projector (+37/-40 degrees). 
21  Keystone adjustment ­ Press to adjust image distortion caused by tilting 
the projector (+37/-40 degrees). 
22  Auto Adjust  Press to synchronize the projector with the input 
source. Auto adjust does not operate if the OSD 
is displayed. 
23  Zoom +  Press to increase the image. 
24  Zoom ­ Press to decrease the image. 
25  VGA  Press to choose VGA source. 
26  Video  Press to choose Composite Video source. 
Using Your Projector  39 
Downloaded From projector-manual.com DELL Manuals 
						

							 
   
       
 1 
Using the Interactive Pen 
Top View	  Bottom View 
1 
2 
6 
3 
5 
8 4 
7 
Replaceable nib	  Press the nib to draw or write. When the nib is 
engaged, it works like left clicking your mouse to 
draw or write. 
NOTE: 
•  If the nib is engaged, the Pen will switch 
to Draw mode and the button function 
will be temporarily disabled. 
•  When the nib wears out, change the nib 
head as shown below. 
Unlock 
Lock 
Using Your Projector 
40 
Downloaded From projector-manual.com DELL Manuals