DELL 1355cnw User Manual

							Understanding the Printer Menus379
 NOTE: This item is displayed only when the printer is connected with a wireless 
network.
Reset Wireless (Dell 1355cnw Multifunction Color Printer only)
Purpose:
To initialize wireless network settings. After executing this function and 
rebooting the printer, all wireless network settings are reset to their default 
values.
 NOTE: This item is displayed only when the printer is connected with a wireless 
network.
TCP/IP
Purpose:
To configure TCP/IP settings. The change becomes effective after the printer 
is turned off and then on.
Va l u e s :
WPS Push 
Button 
ControlPBC 
StartNo*Disables the security method of WPS-
PBC.
Ye sConfigures the wireless setting with the 
security method of WPS-PBC.
PIN Code Start 
Configur
ationConfigures the wireless setting using the PIN code 
assigned automatically by the printer.
Print 
PIN 
CodePrints the PIN code. Confirm it when you enter 
the PIN code to your computer.
No*Does not reset the wireless setting.
Ye sResets the wireless setting.
IP 
ModeDual Stack*Uses both IPv4 and IPv6 to set the IP address.
IPv4 ModeUses IPv4 to set the IP address.
 
						

							380Understanding the Printer Menus
Protocol
Purpose:
To enable or disable each protocol. The change becomes effective after the 
printer is turned off and then on.
Va l u e s :
IPv4 Get IP 
AddressAutoIP*Automatically sets the IP address.
BOOTPUses BOOTP to set the IP address.
RARPUses RARP to set the IP address.
DHCPUses DHCP to set the IP address.
Pa n e lEnables the IP address entered on the operator 
panel.
IP AddressManually sets the IP address allocated to the printer.
Subnet MaskManually sets the subnet mask.
Gateway AddressManually sets the gateway address.
LPD DisableDisables the LPD port.
Enable*Enables the Line Printer Daemon (LPD) port.
Port9100 DisableDisables the Port9100 port.
Enable*Enables the Port9100 port.
WSD DisableDisables the WSD port.
Enable*Enables the WSD port.
SNMP DisableDisables the SNMP UDP port.
Enable*Enables the Simple Network Management Protocol 
(SNMP) UDP port.
E-Mail Alerts DisableDisables the E-Mail Alert feature.
Enable*Enables the E-Mail Alert feature.
EWS DisableDisables an access to Dell Printer Configuration 
We b  To o l embedded in the printer.
Enable*Enables an access to Dell Printer Configuration 
We b  To o l embedded in the printer.
 
						

							Understanding the Printer Menus381
Initialize NVM
Purpose:
To initialize wired network data stored in NVM (non-volatile memory). After 
executing this function and rebooting the printer, all wired network settings 
are reset to their default values.
Fax Settings
Use the Fax Settings menu to configure the basic fax settings. 
 NOTE: Values marked by an asterisk (*) are the factory default menu settings.
Receive Mode
Purpose:
To select the default fax receiving mode.
Va l u e s :
LLTD DisableDisables the LLTD.
Enable*Enables the LLTD.
Bonjour (mDNS) DisableDisables the Bonjour (mDNS).
Enable*Enables the Bonjour (mDNS).
No*Does not initialize the wired network data stored in NVM.
Ye sInitializes the wired network data stored in NVM.
TEL ModeAutomatic fax reception is turned off. You can receive a fax by 
picking up the handset of the external telephone, pressing the 
remote receive code, and then pressing
 .
FA X  M o d eAutomatically receives faxes.
TEL/FAX 
ModeWhen the printer receives an incoming fax, the external telephone 
rings for the time specified in 
Auto Rec TEL/FAX, and then 
the printer automatically receives a fax. If an incoming call is not a 
fax, the printer beeps from the internal speaker indicating that the 
call is a telephone call.
 
						

							382Understanding the Printer Menus
Auto Rec Fax
Purpose:
To set the interval at which the printer goes into the fax receive mode after 
receiving an incoming call. The interval can be specified within the range of 0 
to 255 seconds. The default is 0 second.
Auto Rec TEL/FAX
Purpose:
To set the interval at which the printer goes into the fax receive mode after 
the external telephone receives an incoming call. The interval can be 
specified within the range of 0 to 255 seconds. The default is 6 seconds.
Auto Rec Ans/FAX
Purpose:
To set the interval at which the printer goes into the fax receive mode after 
the external answering machine receives an incoming call. The interval can be 
specified within the range of 0 to 255 seconds. The default is 21 seconds.
Line Monitor
Purpose:
To set the volume of the line monitor, which audibly monitors a transmission 
through the internal speaker until a connection is made.
Va l u e s :
Ans/FAX ModeThe printer can share a telephone line with an answering machine. 
In this mode, the printer will monitor the fax signal and pick up the 
line if there are fax tones. If the phone communication is using 
serial transmission in your country (such as Germany, Sweden, 
Denmark, Austria, Belgium, Italy, France and Switzerland), this 
mode is not supported. 
DRPD ModeBefore using the Distinctive Ring Pattern Detection (DRPD) 
option, a distinctive ring service must be installed on your 
telephone line by the telephone company. After the telephone 
company has provided a separate number for faxing with a 
distinctive ring pattern, configure the fax setup to monitor for that 
specific ring pattern.
 
						

							Understanding the Printer Menus383
Ring Tone Volume
Purpose:
To set the volume of the ring tone, which indicates that an incoming call is a 
telephone call through the internal speaker when Receive Mode is set to 
Telephone/Fax.
Va l u e s :
Line Type
Purpose:
To select the line type.
Va l u e s :
Tone/Pulse
Purpose:
To  s e l e c t  t h e  d i a l i n g  t y p e .
Va l u e s :
OffTurns off the volume of the line monitor.
LowSets the volume of the line monitor.
Medium*
High
OffTurns off the volume of the ring tone.
Low Sets the volume of the ring tone.
Medium
High*
PSTN*Sets the line type to PSTN.
PBXSets the line type to PBX.
 
						

							384Understanding the Printer Menus
Resend Delay
Purpose:
To specify the interval between transmission attempts within the range of 3 to 
255 seconds. The default is 8 seconds.
Redial Attempts
Purpose:
To specify the number of redial attempts to make when the destination fax 
number is busy, within the range of 0 to 9. If you enter 0, the printer will not 
redial. The default is 3.
Redial Delay
Purpose:
To specify the interval between redial attempts within the range of 1 to 15 
minutes. The default is 1 minute.
Junk Fax Setup
Purpose:
To reject faxes sent from unwanted numbers by accepting faxes only from the 
fax numbers registered in the Phone Book.
 NOTE: Ensure to specify Fax Number before using Junk Fax Setup.
Remote Receive
Purpose:
To n e *Sets the dialing type to Tone.
Pulse(10PPS)Sets the dialing type to Pulse
 (10 pulse per second).
Pulse(20PPS)Sets the dialing type to Pulse
 (20 pulse per second).
Off*Does not reject faxes sent from unwanted numbers.
OnRejects faxes sent from unwanted numbers.
 
						

							Understanding the Printer Menus385
To receive a fax by pressing a remote receive code on the external telephone 
after picking up the handset of the telephone.
Va l u e s :
Remote Rcv Tone
Purpose:
To specify the remote receive code in two digits to start Remote Receive. 
Fax Header
Purpose:
To print the information of sender on the header of faxes.
Va l u e s :
Company Name
Purpose:
To set the name of sender to be printed on the header of faxes. Up to 30 
alphanumeric characters can be entered.
Fax Number
Purpose:
To set the fax number of the printer to be printed on the header of faxes.
Fax Cover Page
Purpose:
To set whether to attach a cover page to faxes.
Off*Does not receive a fax by pressing a remote receive code on the 
external telephone.
OnReceives a fax by pressing a remote receive code on the external 
telephone.
OffDoes not print the information of sender on the header of faxes.
On*Prints the information of sender on the header of faxes.
 
						

							386Understanding the Printer Menus
Va l u e s :
DRPD Pattern
Purpose:
To provide a separate number for faxing with a distinctive ring pattern.
Va l u e s :
Off*Does not attach a cover page to faxes.
OnAttaches a cover page to faxes.
 
						

							Understanding the Printer Menus387
Pa t t e r n  1 - 7DRPD is a service provided by some telephone companies. DRPD 
Patterns are specified by your telephone company. The patterns 
provided with your printer are shown below:
Ask your telephone company which pattern you need to select to 
use this service. For example, Pattern 7 is the New Zealand 
FaxAbility distinctive ringing pattern: rings for 400ms, stops for 
800ms, rings for 400ms and stops for 1400ms. This pattern is 
repeated over and over again. This printer only responds to 
Distinctive Alert cadence(s) DA4 in New Zealand.
Pattern 1
Pattern 2
Pattern 3
Pattern 4
Pattern 5
Pattern 6
Pattern 7
 
						

							388Understanding the Printer Menus
Forward Settings
Purpose:
To set whether to forward incoming faxes to a specified destination.
Va l u e s :
Fax Fwd Number
Purpose:
To enter the fax number of the destination to which incoming faxes will be 
forwarded.
Prefix Dial
Purpose:
To select whether to set a prefix dial number.
Va l u e s :
Prefix Dial Num
Purpose:
To set a prefix dial number of up to five digits. This number dials before any 
auto dial number is started. It is useful for accessing the Private Automatic 
Branch Exchange (PABX).
Discard Size 
Purpose:
Off*Does not forward incoming faxes.
Forward OnlyForwards the incoming faxes to a specified destination.
Print and 
ForwardPrints the incoming fax and forwards it to a specified destination.
Off*Does not set a prefix dial number.
OnSets a prefix dial number.