DELL 1355cnw User Manual

							Installing Printer Drivers on Computers Running Windows89
2Click Guided Setup.
3Click Connect Your Printer.
4Select Wireless Connection, and then click Next.
The setting method selection window appears.
5Select Advanced.
Select a connection method from the following
• Ethernet Cable
•WPS-PIN
 
						

							90Installing Printer Drivers on Computers Running Windows
•WPS-PBC
• Operator Panel
• Dell Printer Configuration Web Tool
Ethernet Cable
1Select Ethernet Cable, and then click Next.
2Follow the instructions, and then click Next.
The 
Advanced Configuration Tool screen appears.
3Select the printer to be configured in the Select Printer screen, and then 
click 
Next.
 NOTE: If the printer to be configured is not listed in the Select Printer screen, 
try the following steps:
•Click Refresh to update the information.
•Click Enter IP Address, and then enter the IP address of your printer.
4Enter the SSID.
5Select Type of wireless network.
6Configure the security setting, and then click Next.
The 
IP Address Settings screen appears.
7Select IP Mode depending on your network scheme.
When 
IPv4 is selected:
Configure the following:
aSelect Ty p e.
bEnter the following items:
•
IP address of your printer
•Subnet Mask
• Gateway Address
When IPv6 is selected:
Configure the following:
aSelect Use Manual Address.
bEnter IP address of your printer.
 
						

							Installing Printer Drivers on Computers Running Windows91
cEnter the gateway address of your network.
When 
Dual Stack is selected:
Configure the 
IPv4 Settings and IPv6 Settings.
8Click Next.
9Ensure that the wireless settings are displayed, and then click Apply.
The 
Complete configuration screen appears.
10Click Next.
11Follow the instructions until the Check Setup screen appears, and then 
click 
Next.
12Confirm there are no errors displayed on the operator panel, and then click 
NO on the Check Setup screen.
 NOTE: If you see any errors, click YES and follow the instruction.
13Click Start Installation.
14Select Local Installation, and then click Next.
15Check if the printer to be installed is listed in the Select Printer screen, 
and then click 
Next.
 NOTE: If the printer to be installed is not listed in the Select Printer screen, try 
the following steps:
•Click Refresh to update the information.
 
						

							92Installing Printer Drivers on Computers Running Windows
•Click Add Printer, and then enter the details of the printer 
manually.
16Configure the required items on the Enter Printer Settings screen, and 
then click 
Next.
17Select the software to be installed, and then click Install.
The 
Congratulations! screen appears.
18Click Finish to exit this tool.
The wireless configuration is complete.
WPS-PIN
 NOTE: WPS-PIN (Wi-Fi Protected Setup-Personal Identification Number) is a 
method to authenticate and register devices required for wireless configuration, by 
entering PIN assignments to a printer and computer. This setting, performed 
through access point, is available only when the access points of your wireless 
router supports WPS.
1Select WPS-PIN, and then click Next.
2Follow the instructions until the Check Setup screen appears.
3Confirm there are no errors displayed on the operator panel, and then click 
NO on the Check Setup screen.
 NOTE: If you see any errors, click YES and follow the instruction.
 
						

							Installing Printer Drivers on Computers Running Windows93
4Select Local Installation, and then click Next.
5Check if the printer to be installed is listed in the Select Printer, and then 
click 
Next.
 NOTE: If the printer to be installed is not listed in the Select Printer, try the 
following steps:
•Click Refresh to update the information.
•Click Add Printer, and then enter the details of the printer manually.
6Configure the required items on the Enter Printer Settings screen, and 
then click 
Next.
7Select the software to be installed, and then click Install.
The 
Congratulations! screen appears.
8Click Finish to exit this tool.
The wireless configuration is complete.
When the WPS-PIN operation is successful and the printer is rebooted, 
wireless LAN connection is completed.
WPS-PBC
 NOTE: WPS-PBC (Wi-Fi Protected Setup-Push Button Configuration) is a method to 
authenticate and register devices required for wireless configuration, by pressing 
the button provided on the access point via wireless routers, and then performing 
WPS-PBC setting on the operator panel. This setting is available only when the 
access point supports WPS.
1Select WPS-PBC, and then click Next.
2Follow the instructions until the Check Setup screen appears.
3Confirm there are no errors displayed on the operator panel, and then click 
NO on the Check Setup screen.
 NOTE: If you see any errors, click YES and follow the instruction.
 
						

							94Installing Printer Drivers on Computers Running Windows
4Select Local Installation, and then click Next.
5Check if the printer to be installed is listed in the Select Printer screen, 
and then click 
Next.
 NOTE: If the printer to be installed is not listed in the Select Printer screen, try 
the following steps:
•Click Refresh to update the information.
•Click Add Printer, and then enter the details of the printer manually.
6Configure the required items on the Enter Printer Settings screen, and 
then click 
Next.
7Select the software to be installed, and then click Install.
The 
Congratulations! screen appears.
8Click Finish to exit this tool.
The wireless configuration is complete.
 NOTE: For WPS-PBC operation on the wireless LAN access point, refer to the 
manual supplied with the wireless LAN access point.
When the WPS-PBC operation is successful and the printer is rebooted, 
wireless LAN connection is completed.
Operator Panel
1Select Operator Panel, and then click Next.
 
						

							Installing Printer Drivers on Computers Running Windows95
2Follow the instructions until the Check Setup screen appears.
3Confirm there are no errors displayed on the operator panel, and then click 
NO on the Check Setup screen.
 NOTE: If you see any errors, click YES and follow the instruction.
4Select Local Installation, and then click Next.
5Check if the printer to be installed is listed in the Select Printer screen, 
and then click 
Next.
 NOTE:  If the printer to be installed is not listed in the Select Printer screen, 
try the following steps:
•Click Refresh to update the information.
•Click 
Add Printer, and then enter the details of the printer 
manually.
6Configure the required items on the Enter Printer Settings screen, and 
then click 
Next.
7Select the software to be installed, and then click Install.
The 
Congratulations! screen appears.
8Click Finish to exit this tool.
The wireless configuration is complete.
 
						

							96Installing Printer Drivers on Computers Running Windows
Dell Printer Configuration Web Tool
1Select Dell Printer Configuration Web Tool, and then click Next.
2Follow the instructions until the Check Setup screen appears.
3Confirm there are no errors displayed on the operator panel, and then click 
NO on the Check Setup screen.
 NOTE: If you see any errors, click YES and follow the instruction.
4Select Local Installation, and then click Next.
5Check if the printer to be installed is listed in the Select Printer screen, 
and then click 
Next.
 NOTE: If the printer to be installed is not listed in the Select Printer screen, try 
the following steps:
•Click Refresh to update the information.
•Click Add Printer, and then enter the details of the printer manually.
6Configure the required items on the Enter Printer Settings screen, and 
then click 
Next.
7Select the software to be installed, and then click Install.
The 
Congratulations! screen appears.
8Click Finish to exit this tool.
The wireless configuration is complete.
 
						

							Installing Printer Drivers on Computers Running Windows97
When the Dell Printer Configuration Web Tool operation is successful and 
the printer is rebooted, wireless LAN connection is completed.
Setting up a New Wireless Network Environment for Your Computer 
(When you need to setup your wireless connectivity with your 
computer)
For DHCP network:
1Setting up your computer for wireless connectivity:
 NOTE: You can also change the wireless settings using the wireless 
application that may be installed in your computer.
For Windows XP and Windows Server 2003:
aSelect Network Connections from Control Panel.
bRight-click Wireless Network Connection and select Properties.
cSelect the Wireless Networks tab.
dEnsure that the check box for Use Windows to configure my wireless 
network settings is checked.
 NOTE: Make note of the wireless settings on the Advanced window 
(step f) and the Wireless Network Properties window (step g). You may 
require these settings later.
e
Click the Advanced button.
fSelect Computer to Computer (ad hoc) networks only and close the 
Advanced dialog box.
gClick the Add button to display Wireless network properties.
hOn the Association tab, enter the following information and click OK.
Network name (SSID): dell_device
Network Authentication
: Open
Data encryption
: Disabled
Ad hoc network
: checked
 
						

							98Installing Printer Drivers on Computers Running Windows
iClick the Move up button to move the newly added SSID to the top 
of the list.
jClick OK to close the Property dialog box. 
For Windows Vista:
aOpen Control Panel.
bSelect Network and Internet.
cSelect Network and Sharing Center.
dSelect Connect to a network.
eSelect dell_device from the network items listed in Connect to a 
network
.
fSelect Connect Anyway in the warning dialog box indicating you are 
entering an unsecured area.
gClick Close in the dialog box after confirming the connection is a 
success.
For Windows Server 2008:
aOpen Control Panel.
bSelect Network and Sharing Center.
cSelect Connect to a network.
dSelect dell_device from the network items listed in Connect to a 
network
.
eSelect Connect Anyway in the warning dialog box indicating you are 
entering an unsecured area.