Comdial IPrimo Speakerphone Station User Guide

iPrimo Speakerphone Station User’s Guide
October, 02 Comdial 71
7.  Make your speed dial route selection choice from the list on 
the LCD by pressing the appropriate button.
Figure 6-4  Selecting Line or Intercom
•  Press a line button to select outside line,
•  Dial  00 to select prime line or last line used.
•  Dial  01 to  16  to select line group.
•  Press the INTERCOM  button or dial 8 to select intercom.
Note:  You may need a pause between numbers to compensate 
for differences in response time...

Programming
72 Comdial October, 02
8.  Dial a  number (up to 16 digits long, include * and # if 
needed).
Figure 6-5  Dialing a Speed Number
9.  Select DONE to store the number.
10.  Repeat the  previous steps until all numbers are stored, or 
select  EXIT.
11.  Press SPEAKER to end.
0123456789*#
Pause (P)
Flash (F)
ENTER ERASE DONE 

iPrimo Speakerphone Station User’s Guide
October, 02 Comdial 73
6.3  Feature Access Codes
In addition to the system features which may be programmed using 
the interactive buttons, several other features may be programmed by 
using their access codes.  The feature codes are programmed like 
speed dial numbers and can occupy the same programmable buttons 
on your telephone.  Access codes are listed in Appendix A, Feature 
Access Codes found on page 107.
•  To store a system feature access code,
1.  Select...

Programming
74 Comdial October, 02
5.  Select  the programmable button at which you wish to store 
the feature (remember, if there is anything else programmed 
at this button, the new programming will overwrite it). For 
help in selecting a button, select  SHOW EMPTY LOCA
-
TIONS to display unused feature buttons (green lights). To 
display all feature buttons (used and unused) (red lights), 
select SHOW ALL LOCATIONS.
6.  The speakerphone will now display a list of features which 
you can scroll through...

iPrimo Speakerphone Station User’s Guide
October, 02 Comdial 75
Speed Dial Numbers, Features or DSS/BLF 
Locations
(Programmable Buttons)
113
214
315
416
517
618
719
820
921
1022
1123
1224
Personal Speed Dial Numbers
(Keypad Buttons)
16
27
38
49
50 

Programming
76 Comdial October, 02
6.4  LCD Feature Buttons
You can create feature access buttons to make operation easier. To do 
this, use the interactive buttons to select the feature you want to store, 
and then store it on a programmable button (see the instructions on 
page 79).
•  Account Code —allows you to enter an account code for call 
record purposes.
•  Auto Redial —allows you to redial the last dialed number.
•  Authorization Entry Code  —allows you the mobility to use 
your class of...

iPrimo Speakerphone Station User’s Guide
October, 02 Comdial 77
•  Camp-On (Call Waiting)(CAMP)—when calling a busy 
station, this feature allows you to send a call waiting tone to the 
station and to wait on-line for a reply.
•  Clear Feature (CLEAR)—clears a currently active or engaged 
feature.
•  Do Not Disturb  (DND)—prevents other telephones from 
ringing your telephone.
•  Executive Override —allows overriding a call or a Do Not 
Disturb condition at another telephone.
•  Group Listen —allows...

Programming
78 Comdial October, 02
•  Tracker Paging System (Tracker Access)—allows you to enter 
tracker pager numbers, pickup a tracker page, and either enable 
and/or disable a pager number.
•  Voice-Announce Block —blocks voice announcements.
•  Vo l u m e  S a v e—allows the preset volume level to be saved. 

iPrimo Speakerphone Station User’s Guide
October, 02 Comdial 79
6.4.1  PROGRAMMING FEATURE ACCESS BUTTONS
Programming of the feature access buttons may require several selec-
tions involving many LCD screens.  If an abbreviation used is not 
familiar to you, consult Appendix B, Display Abbreviations on page 
111.
•  To create a feature access button,
1.  Select  OPTIONS.
Figure 6-6  Selecting a Feature
2.  Select Programming.
3.  Select  NEXT until the  Feature Button option appears.
4.  Select Feature...

Programming
80 Comdial October, 02
8.  Select the feature you want to assign to by selecting  the cor-
responding interactive button. (Select NEXT to scroll 
through the list of available feature.
9.  Repeat steps 1 through 7  for other features.
10.  Select  EXIT to end programming.
•  To clear a feature button assignment,
—Repeat the above procedure, but select CLEAR before 
selecting storage location button.
6.5  Reminder Alert
You can set up to two reminder alerts to sound so that you will 
remember...