Comdial Executech System 2000 Lcd Instructions Manual

Station Speed Dial Programming 
(continued) . . . 
l Make line pre-selection if desired. 
l Dial number for storage. 
l Repeat this procedure until all desired numbers are 
stored. 
To end station speed dial programming, 
l Press @. 
i  

Direct Station Selection/Busy Lamp Field 
(DSS/BLF) Programming. . . 
One-key intercom calling with visual indication of telephone status 
can be programmed at softkeys not assigned to lines. 
To program DSS, 
0 
Press @. 
l Press softkey to be programmed as DSS key. 
l Dial extension number. 
l Repeat last two steps for all desired extension 
numbers. 
To end DSS programming, 
l Press SPKR . 
0 
NOTE: An autodial number can also be programmed as a 
secondary function at every DSS/BLF memoty location....

Programming Automatic Redial Key. . . 
The system will allow the last previously dialed number to be 
automatically and repeatedly redialed for approximately ten 
minutes. A softkey must be programmed to provide this feature. 
To program a softkey for use as an automatic redial key, 
l Press tTCM . 
0 
l Press desired softkey. 
l Press # . 0 
l 
Press SPKR . 0 
NOTE: Label button as Auto Redial key. 
Programming Secure Off-Hook 
Voice Announce Key, . . 
The system will allow a station user to make a...

Personal Ringing Tones. . . 
A station user can select one of four different ringing tones for use 
at a station. 
To select one of four different tones for ring signals, 
l Press tTcM , 0 
(selects tones 1, 2, 3, or 4) 
TONE FREQUENCY PAIR WARBLE RATE 
TONE 1 509/610 Hz 10 
Hz 
TONE 2 
763/l 016 Hz 10 Hz 
TONE 3 
509/610 Hz 19Hz 
TONE 4 76311016 Hz 19Hz 
Voice Announce Blocking.. . 
A station can be arranged to prevent voice signalled intercom calls 
and paging announcements from sounding through the...

Line Monitoring. . , 
To activate while on a call, 
. 
Press @. (Light will turn on.) 
l Hang up handset. 
NOTE: If a distant party places the call on hold, the station 
user can monitor in a handsfree manner until the dis- 
tant parfy returns, and then Iift the station handset to 
resume the call. 
To cancel, 
l Lift handset to resume conversation 
s Press @ to disconnect. Speaker light will turn 
off. 
Recall/Flash . . . 
FLASH 
PBX, CENTREX and custom calling services may require this 
feature. 
if a...

Paging. , . 
EXTERNAL PAGING (Requires external paging unit) 
l 
Lift handset. 
l Press line key dedicated to paging 
ma 
l Press softkey pre-pogrammed for paging access or 
dial paging access number. 
Display: 
l 
Make announcement. 
l Hang up. 
ALL-CALL AND ZONE PAGING 
To page, 
l Lift handset. 
l Press lTCM . 0 
l 
Dial zon number - ( m (@, (@ a 
(@ @ , or (@ m for all-call). 
Display: 
Continued on next page . . . 
33  

Paging (continued) , . . 
l Make announcement, stay on line if wating for 
answerback. 
ma 
!. 
l Hang up handset. 
MEET-ME PAGE 
(Answerback of Page) 
An all-call or zone page can be answered from any station in the 
system. 
Lift handset of nearest station, 
l Press ‘KM . 
0 
l Dial @ (@ . 
Display: 
Station Name = Station originating page. 
34  

Do Not Disturb. . . 
To silence a station ringer and appear busy to intercom calls, 
I 
l Press softkey pre-programmed for this purpose. 
(Associated light will turn on.) 
Display: 
NOTE: The calling party will hear two quick tone bursts every 
three seconds. The feature cannot be overridden by the 
calling party. 
To cancel, 
l Press softkey again. (Associated light will turn off.) 
Mute/Han&free Answer Inhibit. . . 
To prevent distant party from hearing while handset is lifted, 
l Press and hold @....

Call Waiting, . . 
Acall waiting tone can be sent to a busy station while the calling 
station waits on line for an answer. 
To activate call waiting, 
l Make intercom call and receive busy signal. 
. Dial a @ a . (Called party hears 
tone.) 
l Remain on line, waiting for called station response. 
To cancel, 
l Hang up handset. 
To answer a call waiting, 
l Hear short tone burst in handset receiver. 
l Complete present call, and hang up. Waiting call 
will begin ringing. 
* Lift handset to answer. 
NOTE:...

Call Forwarding. . . 
A station user can designate another station to be the recipient of 
just the intercom calls and prime line calls that are directed to the 
user’s station or the recipient of all calls that are directed to the 
user’s station. 
CALL FORWARD - PERSONAL 
To forward intercom calls and prime line to another 
telephone, 
l Press @ . 
l Dial extension number of telephone to which calls 
are to be forwarded. 
Display: 
XXXX = Station name or number 
To cancel intercom call and prime line...