Comdial Executech II Model 816 Instructions Manual

Programming 
_ 
IMI 66-031 1 
, 
5. Assign the line specific toll restriction tables per the following 
procedure. Atthis point, 31 toll restriction tables are 
unassigned for the selected line. 
c , 
a. Press a memory key for each table to be assigned to the line. 
Tables 1 through 8 correspond 
to the memory keys 1 through 8. 
A tone burst will sound with each selection. 
b. Proceed with step 6 if other COS programming must be 
performed. 
If programming only the toll restriction 
requirements of a...

Programming 
IPlI 66-031 
.P- STATION COS 
The Station COS programming sets the following station 
characteristics: 
DSS/BLF port enable 
Ringing assignments 
PA port enable 
Access denied 
Prime line selection 
Call origination denied 
Ringing line preference 
Automatic privacy release 
status 
Station toll restriction Night ringing assignment 
All-call and zone paging 
requirements 
confiquration 
Line appearance/key assignment 
Enter the base programming mode: 
The dial tone will sound. 
Press a...

Programming IMI 66-031 ‘I 
6. 
Enable the rlna,inn 
0 1 
dewi qweqya for the station by pressing the 
key on the keypad rf t is feature is desired. 
7. Set the ~&&JQ &J&J, &gst&ti+cre by performing the steps listed 
below. At this point, there are no toll restriction tables 
assigned to this station. 
a. 
Press a memory key for each table to be assigned to the 
station. 
Tables 1 through 8 correspond to the memory keys 1 
through 8. 
A tone burst will sound with each selection. 
b. 
Proceed with step 8...

Programming IMI 66-031 
. 
F“ 10. Set the w for each line. 
a. 
A tone burst will sound. A default 
condition o access not denied will be set on all lines. 
b. 
Press the line select key for each line on which access is to 
be denied. A tone burst will sound after each selection. 
11. Set the m &&J&&Q dgnigd && for each line. 
a. 
A tone burst will sound. 
A default 
origination not denied will be set on all 
lines. 
b. 
Press the line select key for each line on which call 
origination is to be denied....

Programming 
IMI 66-031 
d. To enable origination by zone; x. 
1. 
Press line select key 5 for zone A 
2. 
Press line select key 6 for zone 3 
.-. 
3. 
Press line select key 7 for zone C 
4. 
Press line select key 8 for all-call 
(if it was cleared in step b). 
NOTE 
Step 15 
must be performed last. See previous important note. 
15. Set the && B a w m only if current settings 
are not correct. When power was initially applied to the KSU, the 
system set the line appearance to key assignment so that line...

r 
,- .’ 
PROCEDURE RECORD (Shading Denotes System Default V&es) 
NOTE 
Clrclr th* f9cotd wlu49 aI flpht bafon pwformlnp lha praOnmmlng procadun glwn below. 
1. Bon Iwel Prognm rntt7 
RRIU I TE 
b.Rl”‘F 
c. PNU. In seqmm, 
d. Pnu 
q tI1rIlABl 
2. Pms 
q 3. Pm4 q (TONI! DIALINO) 
or 
PmBl 
8 (PULSE/TONE DIALINQ) 
I.Flwl * NOTE 
Circle Iha dnhd nhn for ti s7h111 belq pognmnnd 
SYSTEM DIALING MODE 
@iai&q 1 PULSE TONE 5WITCHABLE 
1. Pnu nwmory 
kw 13 for lone slgn~lllnp Inlmom. 
OR 
Pm8 munor 
kq 14 for...

IMI 66-031 ’ Programming 
Table 2b. LINE COS PROGRAMMING REFERENCE 
PROCEDURE RECORD 
(Shading Denotes System Default Values) 
I NOTE 
Enter the informatlon in thr box at right beforo parforming 
the programmlng procedures given below. NOTE 
l Chsck oath line number block for the Iine teature that b set. 
0 Write In the calling number and tocatton status 
1. Base love1 program entry 
a. press [INTERCOM] 
b. press m 
2 press 
q (SET ALL LINES PRIVATE) 
3. Press [LINE 
sf3Ec-rj i-a (SET NON-PRIVATE LINES)...

Programming IMI 66-031 .: 
Table 2c. STATION COS PROGRAMMING REFERENCE 
NOTE 
Enter tntorrnatlon or ctrcle derired values below belore 
1. Base kvet program entry Statton Locrtlon: 
b. press 
@SS/BLF CONSOLE 
Poft) DSWBLF console Porl 
ertures buttons 
loll Restrlctlon 
CALL ORIGINATION DENIED 
Auto Prlv. Rel. 
Zones A, B & C) 
(Clears all call, lt desired) 
l-4 (Receive Zone A, 8, C, 
All Call) 
All CM) 
If 0 time out occurs 
perform base level en 
2. Re-enter the stptlo ve at ttme out. 
67-68 (a)  

Programming 
TM1 66-031 
Table 2c. 
STATION COS PROGRAMMING REFERENCE 
: 
-press memory dlallng katuraar buttons 
0 selects table 1 
selects table 2 
aelects table 3 
Delayed Ringing 
f2. 
Pnrr KLINE SELECTI s-8 ( 
epeat steps 24 and 25 for each asslgned llna 
18. Press 
q to disable button and light 
ps 27 and 28 for each unused line 
NOTE 
If a tlme out occurs durtng the programmlng sequence, 
perform base level entry again and proceed at program step 
2. Reanter the statlon number that was active at...

Programming 
IMI 66-031 : 
Table 2c. STATION COS PROGRAMMING REFERENCE 
Enter Intormatlon or clrc 
Ired values below 
Gtatlon Location: 
(DSSIBLF CONSOLE Port 
DSS/BLF Console Port 
PrtmeLlne 
aturer 
buttons 
CALL ORIGINATION DENIED 
(Clears all call. it deslred) 
l-4 (Receive Zone A, 8, C, 
All Call) 
button and light 
ps 27 and 28 for each unused line 
NOTE 
If a time out occurs durtng the progmmmlng sequence, 
perform base level entry again and proceed at progrsm step 
2. Re-enter the Hqtion number...