Comdial Executech II Model 816 Instructions Manual
Have a look at the manual Comdial Executech II Model 816 Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 133 Comdial manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Programming _ IMI 66-031 1 , 5. Assign the line specific toll restriction tables per the following procedure. Atthis point, 31 toll restriction tables are unassigned for the selected line. c , a. Press a memory key for each table to be assigned to the line. Tables 1 through 8 correspond to the memory keys 1 through 8. A tone burst will sound with each selection. b. Proceed with step 6 if other COS programming must be performed. If programming only the toll restriction requirements of a line, repeat step 5 until all lines are programmed. 6. Select the remaining line characteristics by pressing keys on the keypad to choose them per the following chart. A tone burst will sound after each selection to confirm it. I 0 I LINE PORT DISABLED I LINE TYPE 1 AUXILIARY PORT I 2 I TELCO PORT (DEFAULT VALUE) 1 3 PAHX PORT . ..I DIALING I MoDE 31 ’ I I I 1 TIME INTERVAL FOR 8 50 MSEC. LINE RESTORE AFTER HOLD IS ABANDONED 9 300 MSEC. (DEFAULT VALUE) 7. Repeat Steps 5 through 7 for each line. 8. Press the *i 0 key on the keypad. The dial tone will sound. 9. Press the 0 MONITOR key to exit the programming mode. 60
Programming IPlI 66-031 .P- STATION COS The Station COS programming sets the following station characteristics: DSS/BLF port enable Ringing assignments PA port enable Access denied Prime line selection Call origination denied Ringing line preference Automatic privacy release status Station toll restriction Night ringing assignment All-call and zone paging requirements confiquration Line appearance/key assignment Enter the base programming mode: The dial tone will sound. Press a two-key sequence on the keypad which corresponds to the station to be set (i. e.,to choose station 11 press (l)al* A tone burst will sound to confirm a proper selection. An improper selection will result in the dial tone sound indicating a return to the base level mode. NOTE Each time the base programming mode is followed by a station select number, the following features are set to the default values: the DSS/BLF port enable, the PA port enable, the prime line selection, and the ringing line preference enable. Plus, the toll restriction table assignments are disabled. Set the ~&!~g.&~ s;sggg& ggg& g;e&&g (if such a port is required) by pressing the 0 RECALL key. A tone burst will sound to confirm the selection. Skip this step if a DSS/BLF console is not installed at the station port currently being programmed. If this feature is enabled, do not proceed beyond this step unless the port is also to be programmed as a PA port. Set the a &&J&-L SQ&& (only if a PA port is desired) by pressing 0 9 y on the keypad. A tone burst will sound to confirm this Y selection. Skip this step if a PA port is not desired. Do not proceed beyond this step if a PA port selection is made. Set a a~% ’ line select P for the station being programmed by pressing the ey for the line desired or by pressing the 0 ITCM key to select the intercom line. A tone burst will sound to confirm the selection. If more than one line selection key is pressed, the last one pressed selects the accepted prime line. 61
Programming IMI 66-031 ‘I 6. Enable the rlna,inn 0 1 dewi qweqya for the station by pressing the key on the keypad rf t is feature is desired. 7. Set the ~&&JQ &J&J, &gst&ti+cre by performing the steps listed below. At this point, there are no toll restriction tables assigned to this station. a. Press a memory key for each table to be assigned to the station. Tables 1 through 8 correspond to the memory keys 1 through 8. A tone burst will sound with each selection. b. Proceed with step 8 if other station COS programming must be performed. If only programming the toll restriction requirements of a station, proceed with step 16. During an initial station programming sequence, perform all of the remaining programming steps given herein (8 - 14). It is recommended that they be performed in the order that they are presented. During subsequent reprogramming of a station, any step, controlling a feature that does not need to be reprogrammed, can be skipped over. It is not necessary to return to the base programming mode to shift from one programming step to another. A default value is automatically programmed for most of the following characteristics when the selection key is pressed. This default value is overridden by subsequent programming action. IMPORTANT NOTE STEP 15, WHICH SETS THE PROGRAMMING ACTION MUST TO THE BASE PROGRAMMING A line may be programmed for ringing (step 9) but not for direct ringing (step 8) or delayed both ringing features. If step 8 is programmed after step 9 for some reason, disabled. delayed ringing will be BE IMMEDIATELY FOLLOWED BY A RETURN MODE. 8. Set the a& ’ ~&&&JJJ for each line. a. key. A tone burst yi ringing enabled wil 1 soun be se % l onAal%f??+i$s. b. Press the line select key for each line on which direct ringing is desired. A tone burst will sound after each selection. 9. Set the &md J&J~ a&&&e for each line. a. Press the ok 3 i F ey. A tone burst will sound. A default condition of no delayed ringing enabled will be set on all lines. b. Press the line select key for each line on which delayed ringing is desired. A tone burst will sound after each selection. The time of this delay is 15 seconds. 62
Programming IMI 66-031 . F“ 10. Set the w for each line. a. A tone burst will sound. A default condition o access not denied will be set on all lines. b. Press the line select key for each line on which access is to be denied. A tone burst will sound after each selection. 11. Set the m &&J&&Q dgnigd && for each line. a. A tone burst will sound. A default origination not denied will be set on all lines. b. Press the line select key for each line on which call origination is to be denied. A tone burst will sound after each selection. 12. Set the m & mj6; May r9lgae for each line. Qk 6 M a. Press the 8 ey. A tone burst will sound. A default condition o no access to automatic privacy release will be set on all lines. b. Press the line select key for each line on which access to p automatic privacy release is desired. A tone burst will sound after each selection. 13. Set the Q&J&+ w for each line. a. A tone burst will sound. A default condition of no night ringing will be set on all lines. b. Press the line select key for each line on which night ringing is desired. A tone burst will sound after each selection. 14. Set the &&&&a &&j m J&J&J eagabili$y for the station. The system default value fixes all call at all stations in the system. a. A tone burst will sound. This action from zones A, B, and C. b. is desired to clear the station from all-call, press the c. To assign reception by zone: r- 1. Press line select key 1 for zone A 2. Press line select key 2 for zone B ;: Press line select key 3 for zone C. Press line select key 4 for all-call (if it was cleared in step b). 63
Programming IMI 66-031 d. To enable origination by zone; x. 1. Press line select key 5 for zone A 2. Press line select key 6 for zone 3 .-. 3. Press line select key 7 for zone C 4. Press line select key 8 for all-call (if it was cleared in step b). NOTE Step 15 must be performed last. See previous important note. 15. Set the && B a w m only if current settings are not correct. When power was initially applied to the KSU, the system set the line appearance to key assignment so that line 1 matched select key 1, line 2 matched select key 2, etc. (squared pairing). If this squared pairing is desired, skip step 15a and b. a. Press the 7 i 0 key on the keypad. A tone burst will sound. There is no default condition set by pressing this key. b. Assign the pairing. Any desired pairing can be set. All line select keys can be programmed to select the same line if such a condition is desired. (1) Press a line select key. A tone burst will sound. 3 (2) Press the keypad key that represents the line to be paired. Another tone burst will sound. (3) Repeat this sequence for every line select key. C. Disable the line select key and the indicator light for any lines which are unassigned to a particular station: (1) Press the line select key for the unassigned (2) Press the 9 key on the keypad. (3) Repeat this action for each unassigned line. 16. Press the *i 0 key to return to the base programming 17. Repeat steps 1 through 16 for each station connected line. system. 18. Press the 0 MONITOR key to exit the programming mode. 64 mode. to the
r ,- .’ PROCEDURE RECORD (Shading Denotes System Default V&es) NOTE Clrclr th* f9cotd wlu49 aI flpht bafon pwformlnp lha praOnmmlng procadun glwn below. 1. Bon Iwel Prognm rntt7 RRIU I TE b.Rl”‘F c. PNU. In seqmm, d. Pnu q tI1rIlABl 2. Pms q 3. Pm4 q (TONI! DIALINO) or PmBl 8 (PULSE/TONE DIALINQ) I.Flwl * NOTE Circle Iha dnhd nhn for ti s7h111 belq pognmnnd SYSTEM DIALING MODE @iai&q 1 PULSE TONE 5WITCHABLE 1. Pnu nwmory kw 13 for lone slgn~lllnp Inlmom. OR Pm8 munor kq 14 for woke elgnalllng Intercom. 8.Rnr pJ (PAUSE INTERVAL IN SECONDS - ymdlauto dhl) 7.Prnswk.y 1 2 3 4 5 8 7 8 9 0 0.5 1.0 1.5 2.0 3.0 5.0 7.5 10. 15. 20. 5.PNu q 9. Pnu q (PULSE DIAL TlMES - PPI 6 BREAK/MAKE) 10. Fmnr om key 1 10PPIA 40/40 2 2oPPI5 w/44 11. Prnl a 12. Pm1 q (TRANSFER ACCESS INTERVAL IN SECONOS) FIRST ATTEMPTED INTERCOM SIQNALLINO MOOE TONE SIGNALLINB I PAUSI! INTERVAL IN SECONDS 0.5 ,‘$ 1.5 2.0 3.0 5.0 7.5 10. 15. 20. PULSE DIAL TIMES (PPI I BREAK/MAKE) wq TRANSFER ACCESS INTERVAL IN SECONDS ls..U pJ (HOLD RECALL INTERVAL IN SECONDS) HOLO RECALL INTERVAL IN SECONDS TOLL RESTRICTION PROGRAYMlNa REFERENCE. Tabla 2d. TOLL RESTRICTION FROQRAMMINQ REFERCNM Iw 110 baud
IMI 66-031 ’ Programming Table 2b. LINE COS PROGRAMMING REFERENCE PROCEDURE RECORD (Shading Denotes System Default Values) I NOTE Enter the informatlon in thr box at right beforo parforming the programmlng procedures given below. NOTE l Chsck oath line number block for the Iine teature that b set. 0 Write In the calling number and tocatton status 1. Base love1 program entry a. press [INTERCOM] b. press m 2 press q (SET ALL LINES PRIVATE) 3. Press [LINE sf3Ec-rj i-a (SET NON-PRIVATE LINES) 4. Press q 5. Press [LINE SELECTI 6. press q (DISABLED LINE) q (AUXIL LINE) q (TELCO LINE) q (PBX LINE) 7. Select toll restrlctlon tables -Press memory features dlallng buttons a selects table 1 a selects table 2 a selects table 3 a through a selects tables 4 through 8 RESTRICTION 8. Press q (PULSE/TONE DIALING) &I.CIOM ferrun Press q (TONE ONLY DIALING) 3 ku IhG kmy 0. press q (HOLD ABANDON SOms) soktorn wun press q (HOLD ABANDON 3OOms) maw koy 3 10. Repeat steps 5 through 0 for arch Ilne 11. Press q CALLING NO. 12 press IVoNlToRJ NOTE If a time out occurs durtng the prognmmtng sequence, perlorm base kvel entry agaln and proceed at program step 2 or4 I 66
Programming IMI 66-031 .: Table 2c. STATION COS PROGRAMMING REFERENCE NOTE Enter tntorrnatlon or ctrcle derired values below belore 1. Base kvet program entry Statton Locrtlon: b. press @SS/BLF CONSOLE Poft) DSWBLF console Porl ertures buttons loll Restrlctlon CALL ORIGINATION DENIED Auto Prlv. Rel. Zones A, B & C) (Clears all call, lt desired) l-4 (Receive Zone A, 8, C, All Call) All CM) If 0 time out occurs perform base level en 2. Re-enter the stptlo ve at ttme out. 67-68 (a)
Programming TM1 66-031 Table 2c. STATION COS PROGRAMMING REFERENCE : -press memory dlallng katuraar buttons 0 selects table 1 selects table 2 aelects table 3 Delayed Ringing f2. Pnrr KLINE SELECTI s-8 ( epeat steps 24 and 25 for each asslgned llna 18. Press q to disable button and light ps 27 and 28 for each unused line NOTE If a tlme out occurs durtng the programmlng sequence, perform base level entry again and proceed at program step 2. Reanter the statlon number that was active at time out. 67-68 (b) -_____________._
Programming IMI 66-031 : Table 2c. STATION COS PROGRAMMING REFERENCE Enter Intormatlon or clrc Ired values below Gtatlon Location: (DSSIBLF CONSOLE Port DSS/BLF Console Port PrtmeLlne aturer buttons CALL ORIGINATION DENIED (Clears all call. it deslred) l-4 (Receive Zone A, 8, C, All Call) button and light ps 27 and 28 for each unused line NOTE If a time out occurs durtng the progmmmlng sequence, perform base level entry again and proceed at progrsm step 2. Re-enter the Hqtion number that was active at tlme out. 67-68 (c)