Comdial Executech II Model 816 Instructions Manual

c 
Operation IMI 66-031 ’ 
SMDR AND COS PRINTOUT U 
When a data printer is connected to the printer port to print station 
message detail recording (SMDR), 
it can also be commanded to print the 
class of service (COS) programming configuration for the System, 
lines, 
and stations. 
Partial or complete printouts can be obtained. 
When the printer is being used to obtain a COS printout, the SMDR 
function is temporarily halted. SMDR data collection is continued 
by 
the system during a COS printout...

Operation 
IMI 66-031 
SYSTEM COS TOLL RESTRICTION TABLES 
PAUSE TIME 
2.0 SEC 
PULSE DIAL 20 PPS 
FLASH TIME 
720 MSEC 
HOLD RECALL 240 SEC TABLE 1 DENY 
11 
2 0 
3 
4 
LINE COS 
LINE PRV 
RLS 
1 
C.O. 
2 C.O. 
3 C.O. 
4 x C.O. 
5 x 
AUX 
6 
NONE 
7 
PABX X 
8 x PABX X  TYPE PU- 
HOLD TOLL 
LSE 
50MS TABLES 
STATION 13 
TOLL RESTRICTION 
P.A. ENABLE 
PRIME LINE 
LINE 
123 
RING X 
DELAY RING X 
NITE RING 
ACCESS DENY 
ORIGIN DENY 
PRIVACY RLS 123 6 
123 6 
123 6 
123 6 
78 
X 
456 
X 456 
123 
1 
45678...

;, !I .> 
,.I 1,,(, , ,.,/_ 
LINE NUMBER 
PRINTOUT 
LINE 
, I 
1 
lLlNEFEEDj 
2 [CARRIAGE RETuRNIILINEIZE~ 
1. 
2. 
1 DIALED DIGITS - UP TO MAXIMUM OF 32 
(ACCOUNT CODES ARE ISOLATED BY l OR # SYMBOLS) 
NOTES 
CARRIAGE RETURN AND LINE FEED IMMEDIATELY 
FOLLOW LAST PRINTED CHARACTER ON EACH LINE. 
OUTGOING CALL MUST BE OFF HOOK FOR 20 
SECONDS MINIMUM OR NO RECORDING OCCURS. 
- MONTHtDAYNEAR 
INITIATE TIME - HOUR : MINUTE 
(24 HOUR REAL TIME CLOCK) 
CALL DURATION TIME - MINUTES. TENTHS 
(NO ANSWER, PRINT...

Programming IMI 66-031 . 
_. 
; CHAPTER 4 
SYSTEM PROGRAMMING 
I GENERAL INFORMATION 
aClass Of Service (COS) programming consists of setting the Class Of 
Service (COS) operating-condition&. COS programming Is divided into 
the following three major categories: General System COS, Line COS, 
and Station COS. 
0 
l 
l 
/ 
c. 
l 
0 
All COS programming commands must originate at station 10. 
No COS 
programming commands can be accepted from any other station 
connected to the system. 
COS programming...

Programming 
IMI 66-031 
SYSTEM COS 
The System COS programming sets the following system characteristics: 
-DTMF or pulse tone dialing 
-System default conditions 
-Type of signalling first attempted during an intercom call 
-Time interval for a programmed pause used with auto/speed dial 
-Parame.ters for pulse dialing 
-Hookswitch flash time/dial tone recall interval 
-Time out time interval for hold recall 
-Toll restriction table entries 
1. 
Perform the base level program entry procedure: 
Press the...

Programming IMI  66-031 ’ 
-All  lines  either  DTMF  or  Pulse/Tone  switchable  (per step  2b.) 
-Voice  signalling  attempted  first when  intercom call  is made 
-1 sec.  pause  time  -2  sec. dial  tone  recall  time 
-30  sec.  recall  from hold 
-All  lines  private 
-All  lines  are CO  lines 
-No  toll  restriction  set  -300  msec.  held call  abandon  time -No  ringing  line preference  enabled 
-No prime  line  is chosen  -DSS/BLF  port  is disabled 
-PA port  is disabled 
-No  delayed...

r Programming IMI 66-031 , 
4. Select the &+a eiazksax~a iha 0 Jila%sa~~d i2i3YSt; l 
a. Press the 4 B 0 key on the keypad. The dial tone will stop. 
b. Press a key on the keypad to select a time interval from the 
following chart. 
A tone burst will sound to confirm to 
selection. 
3 1.5 8 10.0 
4 2.0 9 15.0 
5 3.0 0 20.0 
. 
5. Press the *i 0 key. The dial tone will sound. 
6. 
Select the a&U &U&U %Wx&W S&U&%&3&S* 
a. 
Press the 
0 5i key on the keypad. The dial tone will stop. 
b. Press a key on the...

Programming IMI 66-031 , 
Press the 0 6 M a. 
8 key on the keypad. The dial tone will stop. 
b. 
Press a key on the keypad to select a time interval per the 
following chart. A tone burst will sound to confirm the 
selection. 
9. Press the *g 0 key on 
10. Select the J-&&d sa&J 
I 0 3.0 SEC. 
J 
the keypad. The dial tone will sound. 
U?& ;ie&rza& 
a. Press the 7 c 
0 key on the keypad. The dial tone will stop. 
 b . Press a key on the keypad to select a time interval from the 
following chart. 
A tone...

Programming 
IMI 66-031 * 
12. Select the ba &wtm~g &&be, g~$&a . Refer to the 
programming table (Table 2d) found at the end of the chapter to 
preselect the entry requirements. 
Figure 8, 
shown below, 
illustrates the keys and keys used to perform the toll restriction 
table entries. 
--,-, SELECTS YMLE 1 CT8 TABLE 0 
82uc?2 melt 2 LECYI ENYRY 1 
8nJm-s TAM.2 2 CYS ENTRY 2 
8LL2CYS TrnLE 1 cls ENYRY 2 
SELECTS PAWE 1 
Cl2ENYRY4 
8ELLcT2 Yull.E 0 
ETS ALLOW TABLE 
EY2 
DENY TABLE 
Figure 8. 
Toll...

Programming 
IMI 66-031 II 
13. 
14. 
/- 15. Press the 
MONITOR 
U key to exit the programming mode.  maximum of 16 digits. 
entered, When the maximum number of digits are 
the system sounds a fast ringhack dial tone and steps 
to the next entry point on a table or to the next table. 
e. If less than the maximum number of digits are required as part 
of a table entry, 
select the next entry location with the 
proper memory key. 
input is required. Select each entry location even if no 
entry is erased....