Comdial Dsu II LCD Speakerphone System Reference Manual

Conferencing Calls
7.1 Conferencing Telephones Together
When your telephone is joined together with several other telephones
on the same call, the effect is called conferencing. You can make
conference calls that involve up to five parties, including you as the
originating party, in any combination of outside lines and intercom
parties. For example, you can conference three outside lines and two
intercom parties or four outside lines and one intercom party or five
intercom parties—the combinations are up...

·To retrieve a line from hold and bring that party back
into the conference,
1. PressTRANSFER/CONFERENCE.
2. Press line button.
3. PressTRANSFER/CONFERENCE.
NOTE: If all the conference circuits are busy, you will not be able to
add a party to the conference. The message “Conference Full” will
appear in your display.
7.2 Making Unsupervised Conference Calls
·To drop out of a conference call between you and two outside
lines (creating an unsupervised conference),
1. Dial # and hang up (lines remain...

Using The Other
Telephone Features
Chapter 8 details the features that enhance the basic operation of your
telephone. All of the features in this chapter are listed in alphabetical
order for your convenience.
8.1 Adjusting The Display Contrast
You can adjust the contrast of the display to darken or lighten it for best
viewing.
·To adjust the display contrast,
1. PressOPTIONS.
2. PressNEXTuntilDISPappears.
3. PressDISP(display reads “contrast level”).
4. PressLIGHTorDARKto change contrast level...

8.2 Blocking Voice Announce Calls
You can prevent voice announcements from sounding over your
telephone speaker. This feature also blocks subdued off-hook voice
announcements as well.
·To block voice-announced calls,
1. PressOPTIONS.
2. PressNEXT.
3. PressVA B.
4. PressON.
5. PressSPEAKERto end.
·To un-block voice-announced calls,
1. PressOPTIONS.
2. PressNEXT.
3. PressVA B.
4. PressOFF.
5. PressSPEAKERto end.
·To block a SOHVA while you are on a call,
1. PressBLOCK.
Using The Other Telephone Features...

8.3 Displaying The Functions Of Your
Station’s Buttons (Button Query)
You can use the interactive buttons on your LCD speakerphone to
access the button query feature. With this feature, you can cause your
station’s display to show the function of each of its buttons.
·To activate the button query feature,
1. PressOPTIONSuntilQUERYappears.
2. PressQUERY.
3. Press any button and read its function in your LCD speakerphone’s
display.
NOTE: Use the SHIFT to access autodial numbers that you have
stored under...

8.4 Entering Account Codes
If your installer has arranged your system for account code entry to
enhance the SMDA reports, you may be told to enter an account code
before calling a number or after answering one. Code entry is either
forced or voluntary. If the codes are forced, you must enter the account
code to place a call; if the codes are voluntary, the call will still go
through if you do not enter a code (pre-programmed Emergency
numbers will automatically go through even with forced account...

8.5 Forwarding Calls
You can forward calls that normally ring at your telephone to another
telephone for answering. You can forward just your prime line and
intercom calls or you can forward any calls that ring at your telephone.
NOTE: You can program a special call forward button if you need
quick access to the feature. See the programming section of
this user’s guide for details.
·To forward your calls,
1. PressOPTIONS.
2. PressNEXTuntilCFWDappears.
3. PressCFWD.
4. PressPERSfor prime line and intercom...

8.6 Activating The Call Forward
Outside System (CFOS) Feature
The Call Forward Outside System (CFOS) feature gives DSU II station
users the ability to forward line calls to a remote location outside the
system. CFOS remains in effect in the event of a loss of power or a
system reset.
·To activate the CFOS feature,
1. PressINTERCOMS07.
2. Press the speed dial button programmed with the target number,
—OR—
Press a line button,
—OR—
Dial0for the Prime line or last used line,
—OR—
Dial1–4Line Group number....

8.7 Identifying Your Telephone
With Automatic Set Relocation
If your installer has equipped your system with automatic set
relocation, you can move your telephone to another location and be
given a choice (through a display prompt) as to whether you want to
keep your previous programming or use the programming in the new
location. Respond to the prompt according to your need.
·To maintain the extension number and programming features
from the old location,
1. Connect the telephone line cord to the new...

8.8 Listening To A Call Over The
Speaker (Group Listening)
You can turn on the telephone speaker while you have the telephone
handset lifted if you wish. The distant party’s voice then sounds over
the telephone speaker as well as the handset; however, only your
handset microphone is active.
·To do this while on a call,
1. Press and holdSPEAKERfor two seconds.
—OR—
press pre-programmed group listening button.
·To cancel group listening,
1. Press and releaseSPEAKERto end.
8.9 Making A Call Non-Private
You...