Comdial Dsu II Digital Telephone System Instructions Manual

3.17 Specialized Route Access (SRA)
The SRA feature allows the system to select a line group based on the digits the user has dialed. By doing
this, it matches calls with their ideal routes. The feature provides a table-driven routing scheme where the
numbers the users dial cause the system to chose a line group after comparing the dialed number with
entries in an office code table, and area code table or, four special area code tables.
You should make a record in Chapter 4 of all programming decisions...

3.17.2 Enable SRA Office Code And Area Code Tables
Description:The office code table matches a dialed office code with one of the office codes that you
have entered in the table, and routes the call over the line group that you have entered for
that office code. The area code table matches a dialed area code with one of the area
codes that you have entered in the table, and routes the call over the line group that you
have entered for that area code.
NOTE: When programming the tables, note that all table...

Area Code Table
To program:1. TypeIS746Sand pressRETURN.
2. From the main menu, type1and pressRETURNfor system COS menu.
3. From the system COS menu, type16for specialized route access menu
and pressRETURN.
4. From specialized route access menu, type3for area code table menu
and pressRETURN.
5. Type1–4for line group to match area codes and pressRETURN.
6. Type area code(s) for routing over programmed group number and pressRETURN.
(type nnn or nnn,nnn,nnn,nnn for one code or several codes or typeALLto...

3.17.3 Enable Special SRA Area Code Tables
Description:The four special area code tables must first match a dialed area code and then match the
dialed office code with office code entries in the matched table. With a complete match
found, the system routes the call over the line group that you have assigned to the
matched office code in the matched special area code table.
NOTE: When programming the special area code tables, note that all office code
entries are defaulted to line group 1; therefore, to...

Assigning line groups to the special office code entries,
To Program:1. From the system COS menu, type16for specialized route access menu and press
RETURN.
2. From specialized route access menu, type4for special area code table menu
and pressRETURN.
3. Type1–4for special table 1–4 and pressRETURN.
4. Type1–4to choose line group 1–4 and pressRETURN.
5. Type all office code(s) that require call routing over the line group that you set in step
4, and pressRETURN(type
nnn ornnn,nnn,nnn,nnn for one code or...

3.17.4 Insert Digits For SRA
Description:You may program the system, on a per line group basis, to insert up to 8 digits before a
dialed number. This feature is useful if the dialed number must match a specific format
for the group being used. You may insert numbers 0–9,S, #, or P for pause.
To Program:1. TypeIS746Sand pressRETURN.
2. From the main menu, type1and pressRETURNfor system COS menu.
3. From the system COS menu, type16for specialized route access menu
and pressRETURN.
4. Type8for assign insert...

3.17.5 SRA Overflow Line Group
Description:You can assign an overflow line group that the system can route calls over when no lines
are free in the line group assigned to the matching entry; otherwise, the system will return
busy tone to the caller when this condition exists.
NOTE: If you arrange for the system to insert digits on a particular line group, an
overflow group will take on the characteristics of the line group that is rolling
over to it including the insert digits.
To Program:1....

3.17.6 SRA Wait Time
Description:Once a caller begins to dial digits, he or she has a certain period of time in which to dial
each new digit. After the caller has stopped dialing digits and the end of the time-out
period has occurred, the system analyzes the dialed digits and routes the call by following
the table-driven routing scheme. Use this procedure to select the SRA wait time.
To Program:1. TypeIS746Sand pressRETURN.
2. From the main menu, type1and pressRETURNfor system COS menu.
3. From the...

3.18 Station Message Detail
Accounting/Reporting (SMDA/SMDR)
The system produces five different call cost reports for printing:
1. Detailed report of all stations.
2. Detailed report of all accounts.
3. Trunk summary report.
4. Department summary report.
5. All records.
The system generates reports automatically for printing whenever it detects that its records storage area is
95 percent full. You can use class of service programming to choose the reports that you want the system
to generate. It...

3.18.1 SMDA Department Numbers
Description:Use this programming feature to define different SMDA department numbers
To Program:1. Dial75.“SMDA PROGRAMMING”
2. Dial04to define department numbers.“SMDA DEPARTMENTS”
3. Dial1–8for department 1–8.“DEPT X”
4. Dial0000–9999for department number.“DEPT X YYYY”
5. DialSfor next department, and repeat steps 3–7 until all departments are numbered.
6. DialSSfor next SMDA feature.
7. DialSSSfor configuration mode.
To change setting, repeat procedure and make different...