Comdial Americom LCD Speakerphone System Instructions Manual

Sending And Receiving Non-Verbal Messages 
Display 1 
Display 2 
Cwait Over 
MS3 
44  

VY,,“,,,Y I .,,Y . .“W..S IV. .a .._.. _ -.--. ...----.Q-- 
LCD Messaging 
You can set system-supplied messages to be received or displayed 
by a calling LCD speakerphone. These messages give informa- 
tion on your telephone status. Get a list of the available messages 
from the attendant and write them on the blank listing chart on the 
next page. 
To turn message on, 
l press ITCM, 
l dial+%OO, 
l dial the desired code number from your message list. The 
default messages of “Back At” and “Call” may be...

Sending And Receiving Non-Verbal Messages 
LCD MESSAGE LIST 
(Write Attendant-Provided Messages Here) 
0 
1 Back At 
2 call 
4 
5 
6 
7 
8 
9 
Assist Button Messaging 
If you have preprogrammed an ASSIST button on your telephone, 
you can use it to send a message to your supervisor, asking for 
assistance while you am on a call. Your message shows in the 
supervisor’s telephone display. 
To send a message for assistance, 
l press ASSIST button that you have preprogrammed, 
l press DSS or dial extension...

“cz,,“,, qj ,~.I IU , ,““I. r.. .a ._-.- _ ---_.~ ” 
Station-To-Station Messaging 
When you call another telephone and no one answers, you may 
leave a reminder that you have called. Do this by turning on the 
BLF light at the called telephone. To allow this to take place, your 
telephone must have previously been stored as a DSWBLF button 
at the called telephone. If your telephone is not stored as a DSS 
at the called telephone, your messaging call goes to the central 
message desk, if one is...

Programming Your Telephone 
Programming For Automatic Dialing 
Automatic dialing is a feature that lets you: 
l dial lengthy numbers using one or two buttons, 
0 store frequently used feature codes, 
l store intercom extension numbers of frequently called 
telephones. 
You can store numbers for automatic dialing at the following 
locations: 
l at any programmable button that is not now assigned as 
a line button or otherfeature by the system ad- 
ministrator or installer, 
l on a secondary level under a...

Autodial Numbers 
1 13 
14 
4 
17 
6 18 
7 
19 
8 20 
21 
11 
23 
12 
Personal Speed Dial Number (Keypad Buttons) 
0 5 
2 
7 
3 
49  

Programming Your Telephone 
Storing Autodial And Speed Dial Numbers 
To store an outside number or a feature code as an autodial or 
speed dial number, follow the display prompts and proceed as 
follows: 
l press OPTIONS, 
l press NEXT three times, 
l press ADIAL 
or SDIAL to choose autodial or speed dial 
programming, 
l press programmable button or keypad button to choose 
storage location, 
l press line button to dial out on or press ITCM, 

l if your system provides line groups, dial 1,2,3, or 4 
for...

Display 1 
DATE TIME 
OPTIONS 
Display 2 
NEXT 
Display 5 
ADIAL SOW NEXT 
Display 6 
Select Location 
Display 7 
Display 8 
Enter Number 
Display 9 
Dwa 
51  

Programming Your Telephone 
Storing A DSS Number 
E;Fflzw~ intercom extension number as a DSS number, proceed 
. 
. 
l press OPTIONS, 
l press NEXT four times, 
l pressDSS, 
l press programmable button to choose location, 
l dial extension number, 
l press next location button and store next DSS number, 
l repeat the previous step until all DSS numbers are stored, 
q 
l press SPKR to end. 
CAUTION: Do not attempt to program interactive buttonr; doing so can 
cause 
features to be made unavailable. If...

Display 6 
uJzi=zRJg 
Display 7 
Select Location 
Display 8 
Dial Extension 
PREV 
53