Cisco Rfgw1d Manual
Have a look at the manual Cisco Rfgw1d Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 53 Cisco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
78-4025112-01 Rev H0 127 Introduction This section provides information for provisioning the RF Gateway 1 for DOCSIS complaint M-CMTS operation using the DEPI control plane. 8 Chapter 8 M-CMTS Data DEPI-CP Operation In This Chapter Provisioning ......................................................................................... 128 Channel Application Mode ............................................................... 129 Status Monitoring ............................................................................... 131 DEPI Feature Highlights .................................................................... 138
Chapter 8 M-CMTS Data DEPI-CP Operation 128 78-4025112-01 Rev H0 Provisioning This section provides information for provisioning the RF Gateway 1 for M-CMTS operation using DEPI - Control plane. Prerequisite configurations: GbE input ports, including Video/Data IP address QAM outputs Channel Application Mode
Channel Application Mode 78-4025112-01 Rev H0 129 Channel Application Mode To Verify Channel Application Mode 1 Navigate to the QAMs page and scroll to the bottom of the page. Result: Channel Application Mode is revealed for each output carrier. Note: The correct setting is DEPI Remote / DEPI Learn. Depi-Remote This is very similar to the DEPI remote static mode where the User can configure the QAM PHY parameters and only on match with the corresponding config on the M- CMTS would the session be set-up Note: The RF-port 1/1 is now editable as all the QAM channels are in DEPI-Remote mode DEPI-Learn This mode is similar to the DEPI remote learn mode where the QAM PHY parameters cannot be configured by the user and would be “learnt” from the configuration on the M-CMTS.
Chapter 8 M-CMTS Data DEPI-CP Operation 130 78-4025112-01 Rev H0 Note: The RF-port 1/1 is not editable as all the QAM channels are in DEPI-Learn mode. Connecting to DTI Server Please refer to Connecting to DTI Server (on page 116).
Status Monitoring 78-4025112-01 Rev H0 131 Status Monitoring Introduction This section provides information for status monitoring for DOCSIS compliant M- CMTS operation. The RF Gateway 1 provides utilities for monitoring: Input streams (i.e., stream activity, input bitrate) Output streams (i.e., per carrier stream mapping, provisioned bitrate) Data specific monitoring (i.e., DOCSIS sync presence) DTI server connectivity and status Monitoring To View Input Monitoring 1 Navigate to the Monitor page. 2 In the tree menu, select the Input/GbE port.
Chapter 8 M-CMTS Data DEPI-CP Operation 132 78-4025112-01 Rev H0 Result: Input monitoring is shown for each GbE port.
Status Monitoring 78-4025112-01 Rev H0 133 To View Output Monitoring 1 Navigate to the Monitor page. 2 In the tree menu, select the Output/Card/RF Port. Result: Output monitoring is shown for each QAM Card.
Chapter 8 M-CMTS Data DEPI-CP Operation 134 78-4025112-01 Rev H0 To View Data Monitoring 1 Navigate to the Monitor page. 2 In the tree menu, select Data. Result: Data monitoring is revealed for each GbE port.
Status Monitoring 78-4025112-01 Rev H0 135 To View Input Details Additional input information (for the output stream) can be retrieved by pressing the Input/Details button on the output monitoring screen. Result: The following screen is displayed.
Chapter 8 M-CMTS Data DEPI-CP Operation 136 78-4025112-01 Rev H0 To View DTI Monitoring 1 Navigate to the Monitor page. 2 In the tree menu, select DTI. Result: DTI monitoring is shown for each DTI server port. Note: DTI timestamp increments (updated ~5s) can be displayed using the Refresh button in the top right-hand corner of the page. To View Tunnel Details 1 Navigate to the Monitor page. 2 In the tree menu, navigate to DEPI details and select tunnels Result: DEPI tunnels are shown for each GbE port.