Cisco Rfgw1d Manual

 
 
78-4025112-01 Rev H0 147 
 
Introduction 
A new Alarm Configuration page has been added to the Web user 
interface to allow for editing of the alarm configuration.  
 
 
10 Chapter 
10 
Alarm Configuration 
In This Chapter 
 Configuring Alarm Settings .............................................................. 148  

 
Chapter 10    Alarm Configuration  
 
 
148 78-4025112-01 Rev H0 
Configuring Alarm Settings 
This new page is accessible from the System tab, and appears as shown in the 
following example: 
 
  
Alarm Details 
 Alarm Name – Name of the Alarm for which the row settings apply.  
 Enable – Enables the Alarm notification for a particular alarm type; this will 
enable the log by default.  
 Log Enable – Enables the log for particular alarm; editable only when the Alarm  

 
 
 Configuring Alarm Settings 
 
78-4025112-01 Rev H0 149 
 
is disabled.  
 Severity – Enables the user to set the severity of alarms (Minor, Major, Critical, 
Warning).  
 Set Threshold/Clear Threshold/Units – Helps to generate or clear alarms based 
on threshold values specified for some alarms.  
This page also contains three additional settings: 
 Apply - Sets any changes made in the Alarm Configuration page (either 
Enable/Severity/Threshold). 
 Reset - Cancels any changes made in the Alarm...

 
 
78-4025112-01 Rev H0 151 
 
Introduction  
Variable Fan Speed is based on the temperature. Currently, the fan 
runs at full speed (setting is 255) irrespective of temperature.  When 
this feature is enabled, the fan speed changes based on the measured 
temperature.  
 
 
11 Chapter 
11 
Variable Fan Speed 
In This Chapter 
 GUI Feature Option ............................................................................ 152 
 Feature Design Details...

 
Chapter 11    Variable Fan Speed  
 
 
152 78-4025112-01 Rev H0 
GUI Feature Option 
GUI option Smart Fan Control is added on the System page of the RFGW-1. 
It has two options: 
 Enabled: The Fan speed changes based on the measured temperatures. 
 Disabled: The Fan always runs at FULL Speed. 
Note: This feature is DISABLED by default. 
 
  

 
 
 Feature Design Details 
 
78-4025112-01 Rev H0 153 
 
Feature Design Details 
When Smart Fan Control changes to Enable there will be a 30 second delay before 
changing the FAN Speed to avoid any FAN related alarms. 
Disabling the Smart Fan Control will make all fans operate at full speed 
immediately. 
This feature flag is unit specific and will not be carried forward to other units when 
using the backup configuration file. 
Based on the temperature, the fan control settings will vary from...

 
 
78-4025112-01 Rev H0 155 
 
Introduction 
To utilize certain software features, a software license is required in 
software releases after 01.02.20.  The license is resident on the chassis, 
and is easy to install using an FTP server.  No license server is 
required after installation. This section describes various applications 
that require a license file and also explains how to install, activate and 
verify the license file on the RF Gateway 1. 
Note: The screens in this section are...

 
Chapter 12    Licensing  
 
 
156 78-4025112-01 Rev H0 
Applications Requiring a Software License 
To access the following features, a license is required after software release 01.02.20.  
 Data streams requiring use of the DOCSIS Timing Interface 
 DVB Encryption 
 PowerKey Encryption 
Note: It is recommended that the user backup the configuration of the RF Gateway 1 
before performing any software upgrade, including license file installation. 
RFGW Licenses  
All of the licenses on the RFGW-1 can...