Cisco Rfgw1d Manual

 
 
78-4025112-01 Rev H0 127 
 
Introduction 
This section provides information for provisioning the RF Gateway 1 
for DOCSIS complaint M-CMTS operation using the DEPI control 
plane.  
 
 
8 Chapter 8 
M-CMTS Data DEPI-CP 
Operation 
In This Chapter 
 Provisioning ......................................................................................... 128 
 Channel Application Mode ............................................................... 129 
 Status Monitoring...

 
Chapter 8    M-CMTS Data DEPI-CP Operation  
 
 
128 78-4025112-01 Rev H0 
Provisioning 
This section provides information for provisioning the RF Gateway 1 for M-CMTS 
operation using DEPI - Control plane. 
Prerequisite configurations:  
 GbE input ports, including Video/Data IP address 
 QAM outputs 
 Channel Application Mode   

 
 
 Channel Application Mode 
 
78-4025112-01 Rev H0 129 
 
Channel Application Mode 
To Verify Channel Application Mode 
1 Navigate to the QAMs page and scroll to the bottom of the page. 
Result: Channel Application Mode is revealed for each output carrier.  
Note: The correct setting is DEPI Remote / DEPI Learn. 
 
  
Depi-Remote 
This is very similar to the DEPI remote static mode where the User can configure the 
QAM PHY parameters and only on match with the corresponding config on the M-
CMTS would...

 
Chapter 8    M-CMTS Data DEPI-CP Operation  
 
 
130 78-4025112-01 Rev H0 
Note: The RF-port 1/1 is not editable as all the QAM channels are in DEPI-Learn 
mode. 
 
Connecting to DTI Server 
Please refer to Connecting to DTI Server (on page 116). 
   

 
 
 Status Monitoring 
 
78-4025112-01 Rev H0 131 
 
Status Monitoring 
Introduction 
This section provides information for status monitoring for DOCSIS compliant M-
CMTS operation. 
 The RF Gateway 1 provides utilities for monitoring: 
 Input streams (i.e., stream activity, input bitrate)  
 Output streams (i.e., per carrier stream mapping, provisioned bitrate)  
 Data specific monitoring (i.e., DOCSIS sync presence) 
 DTI server connectivity and status  
Monitoring 
To View Input Monitoring 
1...

 
Chapter 8    M-CMTS Data DEPI-CP Operation  
 
 
132 78-4025112-01 Rev H0 
Result: Input monitoring is shown for each GbE port. 
  

 
 
 Status Monitoring 
 
78-4025112-01 Rev H0 133 
 
 
To View Output Monitoring 
1 Navigate to the Monitor page. 
2 In the tree menu, select the Output/Card/RF Port. 
Result: Output monitoring is shown for each QAM Card. 
  

 
Chapter 8    M-CMTS Data DEPI-CP Operation  
 
 
134 78-4025112-01 Rev H0 
 
To View Data Monitoring 
1 Navigate to the Monitor page. 
2 In the tree menu, select Data. 
Result: Data monitoring is revealed for each GbE port. 
  

 
 
 Status Monitoring 
 
78-4025112-01 Rev H0 135 
 
 
To View Input Details 
Additional input information (for the output stream) can be retrieved by pressing 
the Input/Details button on the output monitoring screen. 
Result: The following screen is displayed. 
  

 
Chapter 8    M-CMTS Data DEPI-CP Operation  
 
 
136 78-4025112-01 Rev H0 
 
To View DTI Monitoring 
1 Navigate to the Monitor page. 
2 In the tree menu, select DTI. 
Result: DTI monitoring is shown for each DTI server port. 
 
Note: DTI timestamp increments (updated ~5s) can be displayed using the Refresh 
button in the top right-hand corner of the page. 
To View Tunnel Details 
1 Navigate to the Monitor page. 
2 In the tree menu, navigate to DEPI details and select tunnels 
Result: DEPI tunnels are...