Cisco Rfgw1d Manual

 
 
 Provisioning 
 
78-4025112-01 Rev H0 117 
 
2 In the tree menu, select DTI Config. 
 
3 In the Port Mode drop-down box, select desired port mode (for DTI server 
redundancy). 
Note: For proper interoperation with the Cisco uBR10K, the correct setting for 
Port Mode is Auto Non Revert. 
4 In the Primary Port drop-down box, select Primary Port. 
Note: For proper interoperation with the Cisco uBR10K, the correct setting for 
Primary Port is Port 1. 
Note: Connection to the DTI Server can be verified...

 
Chapter 7    Basic M-CMTS Data Specific Operation  
 
 
118 78-4025112-01 Rev H0 
Generally, a service group will first be implemented using a single existing 
downstream primary from the CMTS RF linecard (i.e. the 5x20 linecard).  When 
cable modems come online using the local 5x20 primary downstream, they will 
exhibit a timing offset value that is indicative of processing delays in the 5x20 
and other characteristics of the physical plant (i.e. length of cables, temperatures, 
etc.).  Incidentally,...

 
 
 Status Monitoring 
 
78-4025112-01 Rev H0 119 
 
Status Monitoring 
Introduction 
This section provides information for status monitoring for DOCSIS compliant M-
CMTS operation. 
The RF Gateway 1 provides utilities for monitoring: 
 Input streams (i.e., stream activity, input bitrate)  
 Output streams (i.e., per carrier stream mapping, provisioned bitrate)  
 Data specific monitoring (i.e., DOCSIS sync presence) 
 DTI server connectivity and status  
Monitoring 
To View Input Monitoring 
1...

 
Chapter 7    Basic M-CMTS Data Specific Operation  
 
 
120 78-4025112-01 Rev H0 
Result: Input monitoring is shown for each GbE port. 
  

 
 
 Status Monitoring 
 
78-4025112-01 Rev H0 121 
 
 
To View Output Monitoring 
1 Navigate to the Monitor page. 
2 In the tree menu, select the Output/Card/RF Port. 
Result: Output monitoring is shown for each QAM Card. 
  

 
Chapter 7    Basic M-CMTS Data Specific Operation  
 
 
122 78-4025112-01 Rev H0 
 
To View Data Monitoring 
1 Navigate to the Monitor page. 
2 In the tree menu, select Data. 
Result: Data monitoring is revealed for each GbE port. 
  

 
 
 Status Monitoring 
 
78-4025112-01 Rev H0 123 
 
 
To View Input Details 
Additional input information (for the output stream) can be retrieved by pressing 
the Input/Details button on the output monitoring screen. 
Result: The following screen is displayed. 
  

 
Chapter 7    Basic M-CMTS Data Specific Operation  
 
 
124 78-4025112-01 Rev H0 
 
To View DTI Monitoring 
1 Navigate to the Monitor page. 
2 In the tree menu, select DTI. 
Result: DTI monitoring is shown for each DTI server port. 
 
Note: DTI timestamp increments (updated ~5s) can be displayed using the Refresh 
button in the top right-hand corner of the page. 
To View Tunnel Details 
1 Navigate to the Monitor page. 
2 In the tree menu, navigate to DEPI details and select tunnels 
Result: DEPI...

 
 
 Status Monitoring 
 
78-4025112-01 Rev H0 125 
 
Note: The session Button would display the list of sessions pertaining to each tunnel. 
The statistics button would display the statistics for the sessions associated with each 
tunnel. 
To View Session Details 
1 Navigate to the Monitor page. 
2 In the tree menu, navigate to DEPI details and select Sessions 
Result: DEPI sessions is shown for QAM channel. 
 
Note: The statistics button would display the statistics for this session. 
To View DEPI QAM...