Cisco Rfgw1d Manual

 
 
 Provisioning 
 
78-4025112-01 Rev H0 107 
 
Note: Once a carrier is in data mode, Data Map becomes active for that carrier.  The 
Data Map serves as a routing table which maps incoming data to unique output 
carriers. 
To Configure the Data Map 
1 Navigate to the Maps page. 
2 In the tree menu, select Data Map. 
 
3 Configure the Stream Type to be MPEG for the desired carrier.  
Note: The Stream Type setting of the RFGW-1-D is dependent upon the rf-
channel configuration for the relevant controller...

 
Chapter 6    Wideband Data Specific Operation  
 
 
108 78-4025112-01 Rev H0 
4 Select the Allowable Ingress Ports which receives the flows from the CMTS.  
The correct GbE port (independent mode) or port-pair (port-pair mode) will 
have its GbE port physical address (independent mode) or Video/Data IP 
address (port-pair mode) under the System/IP Network web view configured to 
match the eQAM IP address in the CMTS. 
5 Enter the Destination UDP Port for the input stream to be mapped out to the...

 
 
 Status Monitoring 
 
78-4025112-01 Rev H0 109 
 
Status Monitoring 
Introduction 
This section provides information for status monitoring for video streams using the 
RF Gateway 1 web page. 
The RF Gateway 1 provides utilities for monitoring: 
 Input streams (i.e., stream type, status, IP, UDP, input bitrate) 
 Output streams (i.e., session ID, destination QAM channel)   
Monitoring 
To View Input Monitoring 
1 Navigate to the Monitor page. 
2 In the tree menu, select the Input/GbE port. 
Result:...

 
Chapter 6    Wideband Data Specific Operation  
 
 
110 78-4025112-01 Rev H0 
 
To View Output Monitoring 
1 Navigate to the Monitor page. 
2 In the tree menu, select the Output/Card/RF Port. 
Result: Output monitoring is shown for each QAM Card. 
  

 
 
 Status Monitoring 
 
78-4025112-01 Rev H0 111 
 
 
To View Data Monitoring 
1 Navigate to the Monitor page. 
2 In the tree menu, select Data. 
Result: Data monitoring is revealed for each GbE port. 
  

 
Chapter 6    Wideband Data Specific Operation  
 
 
112 78-4025112-01 Rev H0 
 
To View Input Details 
Additional input information (for the output stream) can be retrieved by pressing 
the Input/Details button on the output monitoring screen. 
Result: The following screen is displayed. 
 
 
  

 
 
78-4025112-01 Rev H0 113 
 
Introduction 
This section provides information for provisioning the RF Gateway 1 
for DOCSIS compliant M-CMTS operation.  
 
 
7 Chapter 7 
Basic M-CMTS Data Specific 
Operation 
In This Chapter 
 Provisioning ......................................................................................... 114 
 Status Monitoring ............................................................................... 119  

 
Chapter 7    Basic M-CMTS Data Specific Operation  
 
 
114 78-4025112-01 Rev H0 
Provisioning 
This section provides information for provisioning the RF Gateway 1 for M-CMTS 
operation. 
Prerequisite configurations:  
 GbE input ports, including Video/Data IP address 
 QAM outputs 
 Channel Application Mode  
Channel Application Mode 
To Verify Channel Application Mode 
1 Navigate to the Maps page. 
2 In the tree menu, select Map Configuration. 
Result: Channel Application Mode is revealed for each...

 
 
 Provisioning 
 
78-4025112-01 Rev H0 115 
 
Note: Once a carrier is in data mode, the Data Map becomes active for that carrier.  
The Data Map serves as a routing table which maps incoming data to unique output 
carriers. 
To Configure the Data Map 
1 Navigate to the Maps page. 
2 In the tree menu, select Data Map. 
Result: The following window is displayed. 
 
3 Configure the Stream Type to be DOCSIS MPT without UDP for the desired 
carrier.  
Note: The Stream Type setting of the RFGW-1-D is...

 
Chapter 7    Basic M-CMTS Data Specific Operation  
 
 
116 78-4025112-01 Rev H0 
4 Select the Allowable Ingress Ports which receives the flows from the CMTS.  
The correct GbE port (independent mode) or port pair (port-pair mode) will have 
its GbE port physical address (independent mode) or Video/Data IP address 
(port-pair mode) under the System/IP Network web view configured to match 
the eQAM IP address in the CMTS. 
5 Enter the Destination UDP Port for the input stream to be mapped out to the...