Cisco Rfgw1d Manual

 
 
 Status Monitoring 
 
78-4025112-01 Rev H0 97 
 
Status Monitoring 
Introduction 
This section provides information for status monitoring for video streams using the 
RF Gateway 1 web page. 
The RF Gateway 1 provides utilities for monitoring: 
 Input streams (i.e., stream type, status, IP, UDP, input bitrate) 
 Output streams (i.e., session ID, destination QAM channel)   
Monitoring 
To View Input Monitoring 
1 Navigate to the Monitor page. 
2 In the tree menu, select the Input/GbE port. 
Result:...

 
Chapter 4    Table-Based Video Specific Operation  
 
 
98 78-4025112-01 Rev H0 
 
To View Output Monitoring 
1 Navigate to the Monitor page. 
2 In the tree menu, select the Output/Card/RF Port. 
Result: Output monitoring is shown for each QAM Card. 
 
To View Input Details 
Additional input information (for the output stream) can be retrieved by clicking the 
Input/Details button on the output monitoring screen. 
Result: The following screen is displayed. 
 
  

 
 
78-4025112-01 Rev H0 99 
 
This chapter provides information for provisioning the RF Gateway 1 
for Switched Digital Video (SDV) operation.  
 
 
5 Chapter 5 
Switched Digital Video 
Specific Operation 
In This Chapter 
 Provisioning ......................................................................................... 100 
 Status Monitoring ............................................................................... 103  

 
Chapter 5    Switched Digital Video Specific Operation  
 
 
100 78-4025112-01 Rev H0 
Provisioning 
This section provides information for provisioning the RF Gateway 1 for SDV 
operation. 
Prerequisite Configurations:  
 GbE input ports, including Video/Data IP address 
 QAM outputs 
 Channel Application Mode = SDV 
Once a carrier is in SVD mode, it should be used with an SRM (e.g., USRM, DNCS) 
and SDV Server configured with all the required video sessions.  
Channel Application Mode 
To Verify...

 
 
 Provisioning 
 
78-4025112-01 Rev H0 101 
 
Result: SRM Configuration page is shown.  
 
2 Enter a valid SRM IP Address. 
3 Set the ‘GQI Announce Mode’ to Enabled, if the RFGW-1 must send the GQI 
Announce Messages to the SRM to indicate the events on the Video Plane.  
Legacy Mode 
Legacy mode is intended to make older DNCS software versions (greater than 4.5) to 
support the RFGW-1 by spoofing the DNCS into thinking the RFGW-1 is a GQAM. 
A DNCS crash is likely if the Legacy Mode is selected with...

 
Chapter 5    Switched Digital Video Specific Operation  
 
 
102 78-4025112-01 Rev H0 
Result: QAM Channel Configuration is displayed. 
 
3 Select SDV for Channel Application Mode. 
4 Enter a unique integer as the Transport Stream ID. 
5 Click Apply. 
6 Click Save. 
  

 
 
 Status Monitoring 
 
78-4025112-01 Rev H0 103 
 
Status Monitoring 
For information on Status Monitoring, refer to Status Monitoring (on page 97). 
  

 
 
78-4025112-01 Rev H0 105 
 
This section provides information for provisioning the RF Gateway 1 
for Cisco Wideband operation.  
 
 
6 Chapter 6 
Wideband Data Specific 
Operation 
In This Chapter 
 Provisioning ......................................................................................... 106 
 Status Monitoring ............................................................................... 109  

 
Chapter 6    Wideband Data Specific Operation  
 
 
106 78-4025112-01 Rev H0 
Provisioning 
This section provides information for provisioning the RF Gateway 1 for Cisco 
Wideband operation. 
Prerequisite Configurations:  
 GbE input ports, including Video/Data IP address 
 QAM outputs 
 Channel Application Mode  
Channel Application Mode 
To Verify Channel Application Mode 
1 Navigate to the Maps page. 
2 In the tree menu, select Map Configuration. 
Result: Channel Application Mode is revealed for...