Cisco Rfgw1d Manual

 
 
 Steps To Take 
 
78-4025112-01 Rev H0 197 
 
Result: The entry is highlighted as shown in the following screen. 
 
2 Click Apply to accept change or Reset to abort.  
Descriptor Rule Parameters 
The following table describes the Descriptor Rule parameters. 
Parameter Description 
Name Identification of the descriptor rule. 
Type Allows you to select the rule type. 
 Add Private Data -  add data to the standard descriptor. 
 Do Not Insert - prevents updating the CA descriptor in the PMT if 
the...

 
Chapter 13    Encryption and Scrambling  
 
 
198 78-4025112-01 Rev H0 
Event Information Schedulers 
The EIS provides the SCS with SCGs containing relevant information to scramble 
services.  To establish communication between the EIS and the SCS, a TCP 
connection should be made followed by a channel set up.  Once the connection is 
made, the SCS of the RFGW-1 receives SCGs from the EIS. To set up a TCP 
connection between the EIS and the RFGW-1, the EIS requires the knowledge of the 
IP address and...

 
 
 Steps To Take 
 
78-4025112-01 Rev H0 199 
 
Result: The following page is displayed. 
 
3 Click Add New EIS. 
Result: The new EIS is added to the table. 
 
4 Click Apply to accept change, or Reset to abort.  
Removing an EIS 
Follow the instructions below to remove an EIS. 
1 Select the check box next to the Rule you want to remove. 
Result: The row is highlighted.  
2 Click Apply to accept change or Reset to abort.  

 
Chapter 13    Encryption and Scrambling  
 
 
200 78-4025112-01 Rev H0 
  
EIS Parameters 
The following table describes the EIS parameters. 
Parameter Description 
EIS Name Identifies the EIS  in the CA System. 
TCP Port Listening port number used by the RFGW-1 to establish TCP 
connection with the EIS. 
Note: The TCP listening port number must be unique and cannot be 
used by an EMM Generator or a PSI Generator. 
EIS Port Selection The Ethernet port to use for communication with the EIS. 
Overrule...

 
 
78-4025112-01 Rev H0 201 
 
This chapter describes the Cisco RF Gateway 1 security features 
including GUI authentication, HTTPS and SFTP support.  
 
 
14 Chapter 
14 
Secuirty Features 
In This Chapter 
 Security Features Overview .............................................................. 202 
 Authentication ..................................................................................... 203 
 Enabling HTTPS on the RF Gateway 1 ............................................ 210 
 SFTP...

 
Chapter 14    Secuirty Features  
 
 
202 78-4025112-01 Rev H0 
Security Features Overview 
The following features are supported in software version 6.1.x. 
 Local and remote authentication for accessing RFGW GUI. 
 HTTPS support 
 SFTP support (SSHv2 with DSA key supported). 
 DSA key download for SFTP. 
 SFTP client support to perform release management, backup/restore 
configuration, license management, and SSL/SSH key download. 
 Firewall settings to enable or disable SFTP, FTP, HTTPS, HTTP,...

 
 
 Authentication 
 
78-4025112-01 Rev H0 203 
 
Authentication 
Password-based authentication is available for RF Gateway 1 users operating 
software release 06.1.x. This chapter describes how to configure user authentication 
capabilities. The unit can be operated without authentication enabled (default 
factory setting) or enabled in two user-settable (Local and Remote) modes of 
operation.  
Authentication Configuration 
The RF Gateway 1 is shipped to customers with the authentication default...

 
Chapter 14    Secuirty Features  
 
 
204 78-4025112-01 Rev H0 
Result: The login UI screen is displayed. 
 
Local user names can be entered as one of the following: admin, rfgw1, rfgw2, 
rfgw3, rfgw4 and rfgw5. Note: admin is a read-write user. The other users are 
read-only users. 
4 Enter 0000 as the default password. 
5 Click Login. 
Result: The following screen is displayed. 
 
6 Click OK.  
Read-Only/Read-Writer User 
1 In the Login UI, login as rfgw1 (local user). 
2 Edit the configurations in...

 
 
 Authentication 
 
78-4025112-01 Rev H0 205 
 
The following screen is displayed. 
 
4 Login as admin. 
5 Edit the configurations in RF Gateway 1 web pages and click Apply. Note: Only 
admin user can make changes to RF Gateway 1 configurations, save the 
configuration or reboot the RF Gateway 1. 
6 The settings are applied. 
To Change Timeout 
1 Navigate to the System/Authentication page. 
2 Click the dropdown box for Timeout and select the appropriate timeout value. 
  
To Change Default Password 
1...

 
Chapter 14    Secuirty Features  
 
 
206 78-4025112-01 Rev H0 
Result: The following page is displayed. 
 
3 Change your password. 
4 Click Apply.  
5 Click Save on the main menu bar to save your settings.  
To Edit Local Users 
1 Login as admin. 
2 Navigate to the System/Authentication page. 
3 Click the + sign and select Edit Local Users. 
Result: The following page is displayed. 
 
4 Select the Login-id to edit. 
5 Enter the value for Rename login-id to. 
6 Enter New password and Confirm password....